• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.10
• /
• pp.2563-2573
• /
• 1993

The measurements of monochromatic line-of-sight flame emission and light transmission in the same path having small spatial resolution were performed in an axisymmetric laminar propane $C_{3}H_{8}$ diffusion flame. The light wavelengthes of 632 nm, 800nm, 900nm were used. From these measurements, local point soot radiances (by Kirchhoff's law) and absorption coefficients were reconstructed by tomography. Thus local point soot temperatures and concentrations were obtained. The reconstructed soot temperatures and concentrations of local points have no differences between the case of visible range (632 nm) and the case of infrared range (800 nm and 900 nm). In these ranges, the scattering coefficient is much lower than the absorption coefficient. Soot mean temperature over the path also matches well with local soot temperature in outer region of the flame. Temperature measurement by thermocouple with different bead diameters $(222{\mu}m and 308{\mu}m)$ was carried in the same flame. Rapid insertion technique was used and radiation effect was considered. Radiation correction in the sooting region was carried out and the corrected result was in good agreement with the local soot temperature.

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.10a
• /
• pp.103-104
• /
• 2009

We proposed the laminate thin film asymmetric Extruded-closed-polygon diffusion pattern that was able to improve the performance of back light unit. Developed a pattern of brightness and bright line, half-power angle attribute the improved performance in the uniform, and through the formation of a thin film stackable diffusion layer 970% improved perpendicularity brightness, and 580% improved horizontality brightness.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.769-775
• /
• 2002

The results gained as part of the study on weldability of compositions from steels, aluminium, titanium alloys in various combinations including similar and dissimilar metal bonding variants with reference to solution of specific practical problems are presented in this work. It has been shown that in the case of HIP/DB carried out with direct interaction of bonding surfaces of the most dissimilar material combinations under study, formation of high-quality joints is not assured due to various reasons. That is why development of special bonding techniques was required. The bonding techniques developed and used for HIP/DB of dissimilar steels, "Steel-bronze", "Titanium-niobium"; "Titanium-steel" and other compositions under study ensured vacuum-tight microvoid-free joints strength of a which was equal to the milder parent metal, including those obtained at reduced welding pressures. Examples of new products manufactured by HIP/DB using the technologies developed are presented.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.11
• /
• pp.136-141
• /
• 1994

In this paper, we implemented an opto-electronical signal processing system for the edge detection using the diffusion neural network. The diffusion neural network performs a Gaussian and DOG operation efficiently by the diffusion process. The diffusion neural network is more efficient than the LOG masking method in hardware implementation because it has a few connections and the connection weights are fixed-valued. We implemented a diffusion neural network using the characteristics of the light intensity distribution function which is similar to the Gaussian function. We have shown that the system can detect the edge of an image exactly through the experimental results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.510-513
• /
• 2003

Our Zn diffusion into n-type $GaAs_{0.40}P_{0.60}$ used ampoule-tube method to increase IV. N-type epitaxial wafers were preferred by $H_2SO_4$-based pre-treatment. $SiO_2$ thin film was deposited by PECVD for some wafers. Diffusion times and diffusion temperatures respectability are 1, 2, 3 hr and 775, $805^{\circ}C$. LED chips were fabricated by the diffused wafers at Fab. The peak wavelength of all chips showed about $625{\sim}650\;nm$ and red color. The highest IV is about 270 mcd at the diffusion condition of $775^{\circ}C$, 3h for the wafers which didn't deposit $SiO_2$ thin films. Also, the longer diffusion time is the higher IV for the wafers which deposit $SiO_2$ thin films.

• Restorative Dentistry and Endodontics
• /
• v.39 no.1
• /
• pp.32-38
• /
• 2014

Objectives: In this study, we evaluated the antibacterial activity of self-etching adhesive systems against Streptococcus mutans using the agar diffusion method. Materials and Methods: Three 2-step systems, Clearfil SE Bond (SE, Kuraray), Contax (CT, DMG), and Unifil Bond (UnB, GC), and three 1-step systems, Easy Bond (EB, 3M ESPE), U-Bond (UB, Vericom), and All Bond SE (AB, BISCO) were used. 0.12% chlorhexidine (CHX, Bukwang) and 37% phosphoric acid gel (PA, Vericom) were used as positive controls. Results: The antibacterial activity of CHX and PA was stronger than that of the other groups, except SE. After light activation, the inhibition zone was reduced in the case of all 2-step systems except CT. However, all 1-step systems did not exhibit any inhibition zone upon the light activation. Conclusions: SE may be better than CT or UnB among the 2-step systems with respect to antibacterial activity, however, 1-step systems do not exhibit any antibacterial activity after light curing.

• Fire Science and Engineering
• /
• v.24 no.6
• /
• pp.170-175
• /
• 2010

The effect of carbon dioxide addition on soot formation was investigated in jet diffusion flames in coflow. Flame temperature were measured with R-type thermocouple and the boundary temperature between blue and yellow flame was confirmed. Light-extinction method was introduced for the relative soot density (1-I/$I_0$) in the in-flame region. He-Ne laser with wave length at 632.8 nm was used for the light source, and the signal attenuated by absorption and scattering was detected directly. Oxidizer velocity effect on soot formation was studied to know that the thermal influence for soot formation. The results showed that the temperature of both blue and yellow flame were decreased according to the dilution of carbon dioxide but boundary temperature was nearly constant. The relative soot density was lower when carbon dioxide was added in oxidizer stream and oxidizer velocity increased. These were caused by the reduction of flame temperature and shorter residence time for soot growth. Also carbon dioxide addition enhanced the instability of jet flames like flickering, so the flame length was a little longer than pure ethylene/air flame.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2011.05b
• /
• pp.99-104
• /
• 2011

Daylighting system is an alternative to the energy crisis and environment change. And it is possible improvement system of Architectural Space Environment. Accordingly, it is very useful system. Because Daylight Duct System of Daylighting System gives high performance for its price, distribution rate is very high. But Daylighting Duct System is hard to accurate control. Accordingly, it is difficult to maintain continuously Daylight Environment in Interior Spaces. Lighting Diffusion System has been developed that it is Applying the principle of Reflector and prism diffuser for maximize the efficiency of lighting of Daylight Duct Systems through this study. And then compare lighting performance of Existing System and new Lighting Diffusion System through producing a mock-up. Thus, this study was carried out for the purpose of verification for excellence. It is that installed Each Daylighting Duct System for performance evaluation in a laboratory of width 4m, length 10m, height 2.5m. And illuminance was measured at noon on winter solstice(December 22) under clean sky. The actual measurement result was in the following. Newly developed lighting Diffusion system was measured maximum illuminance 399, minimum illuminance 221, average illuminance 141. Synthetically, daylight factor, uniformity factor and illuminance distribution were improved more than existing system. As a result, it was confirmed that was improved lighting Environment in Interior Spaces.

• Transactions of Materials Processing
• /
• v.16 no.2 s.92
• /
• pp.144-149
• /
• 2007

The superplastic forming/diffusion bonding(SPF/DB) is widely used in the automotive and aerospace industry because it has great advantage to produce complex, light and strong parts. But the superplastic forming process requires much forming time and generates excessive thinning in the thickness distribution of formed part. It is necessary to minimize trial and error for SPF/DB Process. Finite element analysis using $L_{18}$ orthogonal may table of Taguchi method for 3-Sheet D/B process is carried out. Through the study, effect of process parameters, such as DH region size, thickness and friction coefficient, is evaluated and the optimum condition is derived.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.3
• /
• pp.378-386
• /
• 2009

The effect of fuel mixing on soot structure with methane, ethane, and propane to ethylene-base counterflow diffusion flames has been investigated by measuring the volume fraction, number density, and particle size of soot by adopting the light extinction/scattering techniques. The experimental result showed that the mixing of ethane and propane in ethylene diffusion flame increased soot volume fraction while the mixing of methane decreased. As compare to the ethylene-base flame, the diameters of soot particles for mixture flames are slightly smaller. While the soot number densities for the mixture flames are much higher. Thus, the increase in the soot volume fraction can be attributed to the appreciably increased soot number density by the fuel mixing.