• 전기화학회지
• /
• 제13권2호
• /
• pp.110-115
• /
• 2010

The plasticized polymer electrolytes based on polyvinylidene fluoride-co-hexafluoropropylene (P(VdF-co-HFP)), tetra (ethylene glycol) dimethyl ether (TEGDME), and lithium perchlorate ($LiClO_4$) are prepared for the lithium sulfur batteries by solution casting with a doctor-blade. The polymer electrolyte with EO : Li ratio of 16 : 1 shows the maximum ionic conductivity, $6.5\;{\times}\;10^{-4}\;S/cm$ at room temperature. To understand the effect of the salt concentration on the electrochemical performance, the polymer electrolytes are characterized using electrochemical impedance spectroscopy (EIS), infrared spectroscopy (IR), viscometer, and differential scanning calorimeter (DSC). The optimum concentration and mobility of the charge carriers could lead to enhance the utilization of sulfur active materials and the cyclability of the Li/S unit cell.

• Bulletin of the Korean Chemical Society
• /
• 제28권6호
• /
• pp.1015-1020
• /
• 2007

A simple approach to prepare arrays of Au/TiO2 composite nanoparticles by using Au-loaded block copolymers as templates combined with a sol-gel process is described. The organic-inorganic hybrid films with closely packed inorganic nanodomains in organic matrix are produced by spin coating the mixtures of polystyrene-block-poly(ethylene oxide) (PS-b-PEO)/HAuCl4 solution and sol-gel precursor solution. After removal of the organic matrix with deep UV irradiation, arrays of Au/TiO2 composite nanoparticles with different compositions or particle sizes can be easily produced. Different photoluminescence (PL) emission spectra from an organic-inorganic hybrid film and arrays of Au/TiO2 composite nanoparticles indicate that TiO2 and Au components exist as separate state in the initial hybrid film and form composite nanoparticles after the removal of the block copolymer matrix.

• Nuclear Engineering and Technology
• /
• 제32권5호
• /
• pp.514-520
• /
• 2000

The mechanism of corrosion behavior has to be understood clearly to select an optimum material for handling molten salts to be used in the oxide reduction process of PWR spent fuel. In this study, the oxidation states of corrosion products on the surface of Inconel 600 and 800H as well as their chemical compositions and structural informations were determined by using XPS, ICP-AES, AAS, EPMA and XRD after the corrosion experiment with lithium molten salts at 75$0^{\circ}C$ for 25 hours. Nickel and oxygen were detected from the corrosion products on the surface of Inconel plates and chromium was found to be dissolved out into lithium molten salts leaving cracks on the surface. The corrosion products were identified as metal oxides such as Fe$_2$O$_3$, Cr$_2$O$_3$, NiO, NiFe$_2$O$_4$and MnO by using XPS and XRD.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2000년도 추계학술발표논문집
• /
• pp.15-21
• /
• 2000

In chlorine dioxide delignification and bleaching the formation of chlorate is undesirable because it does not react with lignin and is harmful to the environment. Chlorate is mainly formed from the in-situ generated hypochlorus acid which is also the main reason for AOX formation. In previous literature scavengers of hypochlorous acid such as sulfamic aicd, DMSO, and hydrogen peroxide have been added to bleaching stages to reduce AOX formation but less attention has been paid to chlorate reduction. This paper thus focuses on the reduction of chlorate content caused by the following additives, sulfamic acid, DMSO, hydrogen peroxide, and oxalic acid. The results show that only sulfamic acid and DMSO reduce chlorate formation under our chlorine dioxide prebleaching conditions. Results by UV spectroscopy and pH adjustment show that scavengers react with hypochlorous acid much faster than with chlorine. Hydrogen peroxide and oxalic acid react with HClO/$Cl_2$much slower than DMSO and sulfamic acid do. The reason for the ineffectiveness of hydrogen peroxide and oxalic acid is ascribed to their slow reaction rates with HClO compared to that of chlorate formation. The fact that only 30-35% of the chlorate can be reduced by sulfamic acid and DMSO when charged in same mole ratio to chlorine dioxide, suggested that the reaction rate of DMSO and sulfamic acid with hypochlorous aicd are of the same magnitude as that of chlorate formation.

• Membrane and Water Treatment
• /
• 제15권1호
• /
• pp.21-29
• /
• 2024

1H,1H,2H,2H-perfluorodecytriethoxysilane (C₁₆H₁₉F₁₇O₃Si) be successfully applied to the hydrophobic modification of Al₂O₃ tubular ceramic membrane. Taking the concentration of modification solution, modification time, and modification temperature as factors, orthogonal experiments were designed to study the hydrophobicity of the composite membranes. The experiments showed that the modification time had the greatest impact on the experimental results, followed by the modification temperature, and the modification solution concentration had the smallest impact. Concentration of the modified solution 0.012 mol·L^-1, modification temperature 30 ℃ and modification time 24 h were considered optimal hydrophobic modification conditions. And the pure water flux reached 274.80 kg·m^-2·h^-1 at 0.1MPa before hydrophobic modification, whereas the modified membrane completely blocked liquid water permeation at pressures less than 0.1MPa. Air gap membrane distillation experiments were conducted for NaCl (2wt%) solution, and the maximum flux reached 4.20 kg·m^-2·h^-1, while the retention rate remained above 99.8%. Given the scarcity of freshwater resources in coastal areas, the article proposed a system for seawater desalination using air conditioning waste heat, and conducted preliminary research on its freshwater production performance using Aspen Plus. Finally, the proposed system achieved a freshwater production capacity of 0.61 kg·m^-2·h^-1.

• 대한화학회지
• /
• 제39권8호
• /
• pp.589-597
• /
• 1995

물과 에탄올 혼합 용매에서 전도도법으로 염의 한계 당량 전도도를 구한 후, TATB법으로 이온의 당량전도도를 구하고 Nightingale법으로 이온의 보정 유효반지름을 얻고, 이온에 용매화된 용매의 부피를 계산하여 몇가지 용매화수를 제안하고 이들중에서 해당 이온에 가장 타당한 용매화수$(h_{H_2O}/+h_o)$를 구하고, 해당 이온에 대한 등용매화점을 얻었다. 물과 에탄올 혼합 용매에서의 해당 이온에 대한 등용매화점이 물과 메탄올 혼합 용매에서의 해당 이온에 대한 등용매화점보다 높은 곳에서 나타남을 알 수 있었다. 이는 용매의 $E_T$의 경향과 잘 일치했으며, 이 경향으로 결과 해석이 가능했다. 그리고 해당 이온에 가장 타당한 용매화수로부터 물과 에탄올 혼합 용매의 조성이 바뀜에 따라 해당 이온에 선택적으로 용매화하는 용매를 알았다.

• Bulletin of the Korean Chemical Society
• /
• 제35권7호
• /
• pp.1965-1969
• /
• 2014

A new tetranuclear Mn(III) complex $[Mn^{III}{_4}(sae)_4({\mu}_3-O)({\mu}_{1,1}-N_3)(OH)(H_2O)_2]{\cdot}H_2O$ (1) ($H_2sae$ = 2-salicylideneamino-1-ethanol) has been synthesized by the reaction of $MnCl_2{\cdot}4H_2O$, $H_2sae$ and sodium azide in the mixed solvent of methanol, acetonitrile and water. The X-ray diffraction analysis shows that the four Mn(III) ions in complex 1 have a unique adamantine arrangement, whereas the coordination environment of each Mn(III) ions is different. Magnetic studies indicate that complex 1 manifests antiferromagnetic behaviors. The magnetic susceptibilities of complex 1 have been fitted by two magnetic models based on the suitable analysis of its magnetic structural topology.

• 전기화학회지
• /
• 제2권1호
• /
• pp.1-4
• /
• 1999

리튬이차전지는 충방전의 반복 동안의 액체전해질과 리튬음극과의 반응으로 수지상결정의 성장으로 리튬이 차전지에 있어서 안전성의 문제를 일으킨다. 고분자 전해질은 수지상 결정 형성을 억제하며 전해질에 성능을 향상시키는 연구가 활발히 진행중이다. 본 연구에서는 겔 전해질에 $Al_2O_3$를 첨가하여 전해질의 표면구조와 임피던스 특성을 조사하였다. 리튬이온의 수율은 $10wt\%\;PAN-Al_2O_3$ 전해질에 5mV의 전압을 인가했을 때 0.29였고 전해질의 이온전도도는 상온에서$2.3\times10^{-4} S/cm$였다. 무기 충진제가 고분자 전해질에 첨가되었을 때 이온전도도 및 이온수율은 무기 충진제가 첨가되지 않은 것보다 높게 나타났다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1034-1038
• /
• 1995

The purpose of this study is to research and develop $TiS_2$ composite cathode for lithium polymer battery(LPB). $TiS_2$ electrode represent a class of insertion positive electrode used in Li secondary batteries. In this study, we investigated preparation of $TiS_2$ composite cathode and AC impedance response of $TiS_2$ composite/SPE/Li cells as a function of state of charge(SOC) and cycling. The resistance of B type cell using $TiS_2PEO_8LiClO_4PC_5EC_5$ composite cathode was lower than that of A type cell using $TiS_2PEO$ composite cathode. The cell resistance of B type cell is high for the first few percent discharge, decreases for midium discharge and then increases again toward the end of discharge. We believe the magnitude of the cell resistance is dominated by passivation layer impedance and small cathode resistance. AC impedance results indicate that the cell internal resistance increase with cycling, and this is attributed to change of passivation layer impedance with cycling. The passivation layer resistance($R_f$) of B type cell decreases for the 2nd cycling and then increases again with cycling. Redox coulombic efficiency of B type cell was about 141% at 1st cycle and 100% at 12th cycle. Also, $TiS_2$ specific capacity was 115 mAh/g at 12 cycle.

• 방사성폐기물학회지
• /
• 제8권1호
• /
• pp.33-39
• /
• 2010

산화물 사용 후 핵연료를 처리하는 전해환원공정에서는 LiCl 용융염계에서 산소가 생성되는 반응을 수반하게 되며, 생성된 산소로 인해 반응기의 구조재료를 상당히 부식시킬 수 있는, 화학적으로 심각한 반응환경을 조성한다. 따라서, 고온 용융염을 다루는 전해환원 공정장치를 위해서는 최적의 재료를 선택하는 것이 필수적이다. 본 연구에 서는 리튬용융염, $675^{\circ}C$, 216시간동안 산화분위기에서 코팅이 안 된 초합금과 코팅된 초합금 시편의 고온 부식연구를 수행하였다. IN713LC 초합금 시편에 aluminized NiCrAlY bond 코팅 후 $Y_2O_3$ top 코팅을 하였다. 코팅이 안 된 초합금은 부식층의 빠른 성장응력과 열적응력에 의한 부식층의 박리로 명확한 무게손실을 보인다. 탑 코팅의 화학적 및 열적 안정성으로 인해 고온 리튬용융염을 다루는 구조재료의 부식 저항성이 증가함을 확인할 수 있었다.