• Bulletin of the Korean Chemical Society
• /
• v.23 no.8
• /
• pp.1144-1148
• /
• 2002

We prepared the polyaniline (Pani) film and powder by chemical polymerization and doping with different dopants and also investigated the capability of Li//polyaniline cells after assembling. The oxidation/reduction potentials and electrochemical reaction of Li//polyaniline cells were tested by cyclic voltammetry technique. The Li//Pani-HCl cells with 10% and 20% conductors show a little larger specific discharge capacities than that without conductor. The highest discharge capacity of almost 50 mAh/g at 100th cycle is also achieved. However, Li//Pani-LiPF6 with 20% conductor shows a remarkable performance of ~90 mAh/g at 100th cycle. This is feasible value for using as the positive electrode material of lithium ion secondary batteries. It is also proved that the powder type electrode of Pani is better to use than the film type one to improve the specific discharge capacity and its stability with cycle.

• Bulletin of the Korean Chemical Society
• /
• v.29 no.9
• /
• pp.1695-1698
• /
• 2008

• Journal of the Korean Institute of Intelligent Systems
• /
• v.23 no.3
• /
• pp.214-219
• /
• 2013

This paper proposes the robust high-gain observer based SOC estimatro for uncertain RC model of Li-Ion batteries. In general, RC battery model has inevitable uncertainties and it cause some negative effect to estimate the accurate SOC of Li-Ion batteries. The proposed estimator overcomes such weakness with two techniques; high-gain observer design technique and sliding mode control technique. A high-gain observer provides the robustness against model uncertainties to the proposed estimator. A sliding mode control technique helps the proposed estimator by reducing the side effect of adopting a high-gain observer such as peaking phenomenon and perturbation. The performance of the proposed estimator is verified by some simulation.

• Journal of Hydrogen and New Energy
• /
• v.28 no.4
• /
• pp.407-418
• /
• 2017

Battery heat management is essential for high power and high energy battery system because it affects its performance, longevity, and safety. In this paper, we investigated the temperature of the 18650 Lithium Ion Battery Module used in a Energy Storage System (ESS) and the cooling method to minimize cell-to-cell temperature variation of battery module. For uniform temperature distribution within a battery module, the flow direction of the coolant in a battery module has been changed according to the time interval, and studied the effect of the cooling method on the temperature uniformity in a battery module which includes a number of battery cells. The experimental results show that bi-directional battery cooling method can effectively reduce the cell-to-cell temperature variation compared with the one-directional battery cooling. Furthermore, it is also found that bi-directional battery cooling can reduce the maximum temperature in a battery module.

• Polymer(Korea)
• /
• v.26 no.1
• /
• pp.45-52
• /
• 2002

The separator made from the blends of high density polyethylene (HDPE) and ultrahigh molecular weight polyethylene (UHMWPE) was prepared by wet processing to use as Li-ion secondary battery. We investigated effects of the blending of the polymers and the film extension on the mechanical properties of the separator. The mechanical strength of separator increased with increasing molecular weights and contents of UHMWPE, for instance about $1000 kg/\textrm{cm}^2$ with the five times extended film of 6 wt% UHMWPE. The pores of the separator were very uniform with the size of 0.1~$0.12\mu\textrm{m}$. The shut-down characteristic quickly increased at around $130^{\circ}C$ and the fusion temperature was $160^{\circ}C$, so it could be applied to the lithium ion secondary battery.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.2
• /
• pp.69-74
• /
• 1999

Graphite and carbonaceous materials intercalate and deintercalate Li-ion reversibly into their layered structures. These materials show an excellent capacity for using a negative electrode in Li-ion batteries, because the electrochemical potential of Li-ion intercalated carbon is almost identical with that of lithium metal. Carbon used in this study was obtained by the pyrolysis of petroleum pitch, and heat-treated at the several temperatures between $700^{\circ}C$ and $1300^{\circ}C$. XRD analysis revealed that crystallization of carbon increased with increasing the heat treatment temperature. Charge/discharge properties were studied by a constant-current step at the rate of 0.1C, and the interfacial reaction between the electrolyte and the surface of carbon electrode was studied by cyclic voltammetry. Cell capacities were investigated in terms of the heat treatment temperature and the cycle number. Reversible capacity increased with the heat treatment temperature up to $1000^{\circ}C$, thereafter decreased continuously. Also, charge capacity decreased with the cycle number, while the reversibility improved with it.

• Resources Recycling
• /
• v.28 no.4
• /
• pp.30-36
• /
• 2019

In this study, Li powder was recovered from the by-product of LNO ($Li_2NiO_2$) process, which is the positive electrode active material of waste lithium ion battery, through the $CO_2$ thermal reaction process. In the process of recovering Li powder, the $CO_2$ injection amount is 300 cc/min. The $Li_2NiO_2$ award was phase-separated into the $Li_2CO_3$ phase and the NiO phase by holding at $600^{\circ}C$ for 1 min. After this, the collected sample:distilled water = 1:50 weight ratio, and after leaching, the solution was subjected to vacuum filtration to recover $Li_2CO_3$ from the solution, and the NiO powder was recovered. In order to increase the purity of Ni, it was maintained in $H_2$ atmosphere for 3 hours to reduce NiO to Ni. Through the above-mentioned steps, the purity of Li was 2290 ppm and the recovery was 92.74% from the solution, and Ni was finally produced 90.1% purity, 92.6% recovery.

• Applied Chemistry for Engineering
• /
• v.18 no.3
• /
• pp.273-278
• /
• 2007

The honeycomb adsorbents and adsorption process for carbon dioxide removal from fuel gas were investigated. Zeolite paper was made with Na-X zeolite powder and ceramic fiber as raw materials. $Li^+$, $Ca^{2+}$ or $K^+$ ion exchanges for Na-X zeolite and additional Na-X coating were performed on zeolite paper for increasing the carbon dioxide adsorption capacity, after that the adsorption characteristics of the samples were analyzed. Among the ion exchanged samples, $Li^+$ ion exchanged zeolite paper was most promising but its carbon dioxide adsorption capacity was less than expected for process application. However, additional Na-X coating was found to be an effective method for increasing the carbon dioxide adsorption capacity of the zeolite paper for process application. The carbon dioxide breakthrough test of the honeycomb adsorbent prepared with the zeolite paper was studied, and fuel gas treatment capacity was calculated when the honeycomb adsorbent was used in the rotary adsorption process.

• Korean Chemical Engineering Research
• /
• v.55 no.3
• /
• pp.430-435
• /
• 2017

$Li_4Ti_5O_{12}$ (LTO) is an anode material for lithium ion battery, and the cycle performance is very good. The volume change of LTO during insertion and deinsertion of lithium ion is very small, so the cyclibility is very high. In this experiment graphene and CNT was added to increase the low conductivity of LTO which is the weak point of LTO. When graphene was located on the surface of LTO the conductivity did not increase so much because of the nano size LTO. Addition of CNT increased the conductivity because of the formation of the conducting network between LTO particle and the graphene. Carbon material addition was changed before and after the LTO manufacturing, and the capacity and the cyclibility was compared.

• Journal of Electrochemical Science and Technology
• /
• v.7 no.4
• /
• pp.306-315
• /
• 2016

Amorphous vanadium titanates (aVTOs) are examined for use as a negative electrode in lithium-ion batteries. These amorphous mixed oxides are synthesized in nanosized particles (<100 nm) and flocculated to form secondary particles. The $V^{5+}$ ions in aVTO are found to occupy tetrahedral sites, whereas the $Ti^{4+}$ ions show fivefold coordination. Both are uniformly dispersed at the atomic scale in the amorphous oxide matrix, which has abundant structural defects. The first reversible capacity of an aVTO electrode ($295mAhg^{-1}$) is larger than that observed for a physically mixed electrode (1:2 $aV_2O_5$ | $aTiO_2$, $245mAhg^{-1}$). The discrepancy seems to be due to the unique four-coordinated $V^{5+}$ ions in aVTO, which either are more electron-accepting or generate more structural defects that serve as $Li^+$ storage sites. Coin-type Li/aVTO cells show a large irreversible capacity in the first cycle. When they are prepared under nitrogen (aVTO-N), the population of surface hydroxyl groups is greatly reduced. These groups irreversibly produce highly resistive inorganic compounds (LiOH and $Li_2O$), leading to increased irreversible capacity and electrode resistance. As a result, the material prepared under nitrogen shows higher Coulombic efficiency and rate capability.