• 대한교통학회지
• /
• 제23권2호
• /
• pp.107-116
• /
• 2005

교통정보 제공 측면에서 여행시간에 대한 정보는 교통관리 영역 내에서 교통혼잡을 효과적으로 분산시킬 수 있는 핵심정보 중 하나이다. 특히 여행시간에 대한 정보는 운전자가 운전 중 경로선택을 의사결정하는데 있어서 주요한 요소로서 현실적인 신뢰도 확보를 전제로 한다. 본 연구는 남산권 교통정보시스템의 일환으로 총 연장도로 6.1km를 대상으로 구성된 6개의 교통축(corridor)을 대상으로 혼잡시 VMS, ARS, WEB을 이용한 정보 제공을 목적으로 도착예정시간 알고리즘을 개발하였다. 시스템의 공간적 범위는 각 축별 2~3.5km 범위내의 구간을 대상으로 하며, 각 교통축의 출발 및 도착지점에 신호교차로가 존재하여 단순한 연속교통류 특성이외 단속류 교통특성이 교통류내에 포함되어 있다. 목표 알고리즘은 ILD기초자료를 활용하여 수요교통량과 대기길이정보를 이용한다. 수요교통량은 각 지점간 밀도추정을 대상으로 하였으며 이를 위하여 Greenburg Model이 채택되었다. 대기길이 정보는 각 지점별 속도와 밀도에 의하여 산출된다. 연구모형은 단위시간당 변동성을 안정화하기 위하여 전략적으로 번호판 매칭기법에 의한 AVI를 도입하였으며, 이를 통한 관측 된 여행시간 정보를 이용하였다. AVI여행시간 정보는 1일 1회 대기길이에 따른 교통류 특성을 구분하여 ILD에 의한 여행시간을 생성하는데 기반모수로 적용될 수 있도록 Hybrid Model로 구성하여 적용시켰다. 본 연구에 의한 알고리즘 적용결과, 혼잡상황하에서 84% 그리고 전체평균 88%이상의 정확성을 도출하는 것으로 나타났으며, 이러한 정보들은 남산권 교통정보시스템을 이용하는 운전자들에게 유용한 것으로 조사되었다.

• 대한기계학회논문집B
• /
• 제21권11호
• /
• pp.1485-1495
• /
• 1997

The present study investigates heat/mass transfer around film cooling jets and circular cylinders to compare the characteristics of each other. Experiments are conducted to obtain the detailed heat/mass transfer coefficients of flat plate with injections through an array of holes and for flows around an array of protruding circular cylinders using the naphthalene sublimation technique. The inclination angles of cylinders are set to the same ones of jets; a, the angle between the jet and the surface is fixed at 30 deg. through the whole experiments and .betha., the angle between the projection of the jet on the surface and the direction of main stream is adjusted to 0 deg., 45 deg. and 90 deg. to investigate the effect of variation of injection angles. The influence of blowing rates of jets and those of cylinder length to diameter ratios are also investigated. The results indicate that the increase of angle .betha. influences the spanwise uniformity of heat/mass transfer remarkably for both jets and cylinders, but that variation of cylinder length to diameter ratios has weaker effects on heat/mass transfer coefficients than that of blowing rates.

• 대한약침학회지
• /
• 제12권4호
• /
• pp.51-62
• /
• 2009

Objective & Methods : The purpose of this study was to observe the effects of herbal-acupuncture with Rosae Laevigatae Fructus extact(RLF-HA) at KI10(Umgok) on osteoporosis in ovariectomized( OVX) ddy mice. We carried out several experimental items to analyze the changes in body weight, uterine weight, uterus index, tibial length, the ash bone weight, tibial BMD, serum ALP, serum osteocalcin, serum Ca, and the levels of Ca, P, Ca/P ratio in tibia, and we performed histological and histomorphological analysis as well. Results : 1. Herbal-acupuncture with Rosae Laevigatae Fructus at KI10(Umgok) and saline injection at KI10(Umgok) significantly inhibited the reduction of tibial calcium level in ovariectomized mice. 2. Herbal-acupuncture with Rosae Laevigatae Fructus at KI10(Umgok) significantly inhibited the increase of tibial osteoclast cells in ovariectomized mice. 3. Herbal-acupuncture with Rosae Laevigatae Fructus at KI10(Umgok) significantly inhibited the reduction of tibial trabecular bone thickness(TBT) in ovariectomized mice. 4. Herbal-acupuncture with Rosae Laevigatae Fructus at KI10(Umgok) significantly inhibited the overgrowth of tibial growth plate length(GPL) in ovariectomized mice. Conclusion : These results suggested that herbal-acupuncture with Rosae Laevigatae Fructus at KI10(Umgok) has a therapeutic effect on osteoporosis, and to be put to practical use in the future osteoporosis clinic.

• Structural Engineering and Mechanics
• /
• 제60권4호
• /
• pp.567-594
• /
• 2016

The main objective of the current research is estimating the flexural behavior of ferrocement Ribbed Plates reinforced with composite material. Experimental investigation was carried out on fifteen plates; their dimensions were kept constant at 1200 mm in length, 600 mm width and 100 mm thick but with different volume fraction of steel reinforcement and number of ribs. Test specimens were tested until failure under three line loadings with simply supported conditions over a span of 1100 mm. Cracking patterns, tensile and compressive strains, deformation characteristics, ductility ratio, and energy absorption properties were observed and measured at all stages of loadings. Experimental results were compared to analytical models using ANSYS 10 program. Parametric study is presented to look at the variables that can mainly affect the mechanical behaviors of the model such as the change of plate length. The results showed that the ultimate strength, ductility ratio and energy absorption properties of the proposed ribbed plates are affected by the volume fraction and the type of reinforcement, and also proved the effectiveness of expanded metal mesh and woven steel mesh in reinforcing the ribbed ferrocement plates. In addition, the developed ribbed ferrocement plates have high strength, ductility ratio and energy absorption properties and are lighter in weight compared to the conventional RC ribbed plates, which could be useful for developed and developing countries alike. The Finite Element (FE) simulations gave good results comparing with the experimental results.

• Archives of Reconstructive Microsurgery
• /
• 제5권1호
• /
• pp.106-111
• /
• 1996

Purpose : Propose a surgical technique in donor harvesting method in free vascularized proximal fibular epiphysis. Methodology : Concerned about growth potentials of the transplanted epiphysis in our long term results of the epiphyseal transplanted 13 cases more than 4 years follow-up, anterior tibial artery which contains anterior tibial recurrent artery is most reliable vessel to proximal fibular epiphysis which is the best donor of the free vascularized epiphyseal transplantation. In vascular anatomical aspect proximal fibular epiphysis norished by latearl inferior genicular artery from popliteal, posterior tibial recurrent artery and anterior tibial recurrent artery from anterior tibial artery and peroneal artery through metaphysis. The lateral inferior genicular artery is very small and difficult to isolate, peroneal artery from metaphysis through epiphyseal plate can not give enough blood supply to epiphysis itself. The anterior tibial artery which include anterior tibial recurrent and posterior tibial recurrent artery is the best choice in this procedure. But anterior tibial recurrent artery merge from within one inch from bifucating point of the anterior and posterior tibial arteries from popliteal artery. So it is very difficult to get enough vascular pedicle length to anastomose in recipient vessel without vein graft even harvested from bifucating point from popliteal artery. Authors took recipient artery from distal direction of anterior tibial artery after ligation of the proximal popliteal side vessel, which can get unlimited pedicle length and safer dissection of the harvesting proximal fibular epiphysis. Results : This harvesting procedure can performed supine position, direct anterolateral approach to proximal tibiofibular joint. Dissect and isolate the biceps muscle insertion from fibular head, micro-dissection is needed to identify the anterior tibial recurrent arteries to proximal epiphysis, soft tissue release down to distal and deeper plane to find main anterior tibial artery which overlying on interosseous membrane. Special care is needed to protect peroneal nerve damage which across the surgical field. Conclusions : Proximal fibular epiphyseal transplantation with distally directed anterior tibial artery harvesting technique is effective and easier dissect and versatile application with much longer arterial pedicle.

• 한국농공학회지
• /
• 제24권2호
• /
• pp.49-55
• /
• 1982

The purpose of this study is to classify the factors influenced on the damages of head works suffered from the storm flood occurred on July 22 1980 in both Musim and Bochong rivers and to find out an integral counter measures against the causes influenced on the disaster of head works in the engineering aspect of planning, design, construction and maintenance. In this survey, number of samples was taken 25 head Works, and the counter measures against the causes of their disasters summarized was as follows, 1. In the aspect of planning a. As the flood water level after the establishment of head works is more increased than the level before setting of head works owing to having more gentle slope of river bed between the head works than nature slope of river bed. Number of head works should be reduced for the appropriate annexation of them b. In the place where head works is established on the curved point of levee, the destruction of levee becomes severe by the strong deflective current. Therefore the setting of head works on the curved point should be kept off as long as possible and in case of unavoidable circumstances the construction method such as reinforced concrete wall or stone wall filed with concrete and anchored bank revetments should be considered. 2. In the aspect of design a. As scoring phenomena at up stream is serious around the weir Where the concentration of strong current is present in such a place, up stream apron having impermeability should be designed to resist and prevent scoring. b. As the length of apron and protected bed is too short to prevent scoring as down stream bed, the design length should be taken somewhat more than the calculated value, but in the case the calculated length becomes too long to be profitable, a device of water cushion should be considered. c. The structure of protected river bed should be improved to make stone mesh bags fixed to apron and to have vinyl mattress laid on river bed together with the improvement for increasing the stability of stone mesh bags and preventing the sucked sand from the river bed. d. As the shortage of cut-off length, especialy in case of the cutoffs conneting both shore sides of river makes the cause of destruction of embankment and weir body, the culculation of cut-off length should be taken enough length based on seepage length. 3. In the aspect of design and constructions a. The overturing destruction of weir by piping action was based on the jet water through cracks at the construction and expansion joints. therefore the expansion joint should be designed and constructed with the insertion of water proof plate and asphalt filling, and the construction joint, with concaved shape structure and steel reinforcement. b. As the wrong design and construction of the weep holes on apron will cause water piping and weir destruction, the design and construction of filter based on the rule of filter should be kept for weep holes. c. The wrong design and construction of bank revetment caused the severe destruction of levee and weir body resulting from scoring and impulse by strong current and formation of water route behind the revetment. Therefore bank revetment should be designod and constructed with stone wall filled with concrete and anchored, or reinforced concrete wall to prevent the formation of water flow route behind the wall and to resist against the scoring and impulse of strong stream. 4. In the aspect of maintenance When the damaged parts occurred at head works the authorities and farmers concerned should find and mend them as soon as possible with mutual cooperation, and on the other hand public citizen should be guided for good use of public property.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 춘계학술대회 논문집
• /
• pp.48-53
• /
• 2002

Sheet or plate bending is one of the most important industrial metal forming processes. And considerable attention has been focused on gaining a better understanding of many of bending characteristics. One of defaults in bending process is the springback. In this study, the springback characteristics of tailor-welded strips in U-bending process was investigated. Furthermore, not only the relationships between the springback and the process variables such as the geometry of the tools and thickness combination of workpiece but also the heat effect which affects the springback due to welding process was experimentally considered. First, tailor-welded strips are joined by the laser welding process and consisted of two types of thickness combinations of the SCPI sheet, 0.8t${\times}$1.2t and 0.8${\times}$1.6t to investigate the effect of different thickness combination on the springback. Secondly, two different directionally welded strips, one was welded along the centerline of the strip-width and the other was along the centerline of strip-length, were adopted to compare the effects of the location of weld line on the springback. And three punch profile radii of 3, 9, and 15 m were used. Some cases of the experimental results were simulated by using a commercial FEM code, PAM-STAMP to compare the experimental results to the analytical ones.

• 소성∙가공
• /
• 제12권5호
• /
• pp.440-448
• /
• 2003

Sheet or plate bending is one of the most important industrial metal forming processes. Considerable attention has been focused on gaining a better understanding of bending characteristics. One of defaults in bending process is the springback. In this study, the springback characteristics of tailor-welded strips in U-bending process was investigated. Furthermore, effect of the process variables such as the geometry of the tools, thickness combination of workpiece, and welding prcoessing on springback were experimentally clarified. First, tailor-welded strips are joined by the laser welding process and consisted of two types of thickness combinations of the SCPl sheet, $0.8t{\times}1.2t$ and $0.8t{\times}1.6t$ to investigate the effect of different thickness combination on the springback. Secondly, two different directionly welded strips, one was welded along the centerline of the strip-width and the other was along the centerline of strip-length, were adopted to compare the effects of the location of weld line on the springback. Some cases of the experimental results were compared to the results simulated by using a commercial FEM code, PAM-STAMP and the theoretical results using the springback formula as well.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.363-364
• /
• 2002

Although the factors that cause the failure of orthopedic implants were not clearly determined, it was reported that the shapes of wear debris affect the tribological behavior of artificial implant. Many researches were conducted to examine the wear mechanism by debris but the role of debris shape in inflammatory reaction remains unclear. To observe the debris shape by addition of reinforcement, carbon nanotubes ( CNTs ) were added to ultra high molecular weight polyethylene ( UHMWPE ) to investigate the reinforcement effect of CNTs. CNTs which have a diameter of about 10-50 nm, while their length is about 3-5 nm were produced by the catalytic decomposition of the acetylene gas using a tube furnace. Plate on disc type wear test were performed to evaluate the tribological performance of UHMWPE composites reinforced with CNTs in lubricating condition ( bovine serum ). The wear losses of CNT added UHMWPE in bovine serum were significantly reduced. Worn surface and wear debris of UHMWPE with CNTs and without CNTs were compared to investigate the reinforcement effect of CNT on tribological behavior.

• 한국운동역학회지
• /
• 제30권3호
• /
• pp.217-223
• /
• 2020

Objective: The purpose of this study was to analyze the effect of postural sway on the kinematic variables of the putter head during golf putting and to provide information to the importance of postural sway control in the putting stroke for novice golfers. Method: The center of pressure (CoP) and Kinematics variables of the putter head were calculated during 2 m flat golf putting using 8 motion capture cameras (250 Hz) and 2 force plate (1,000 Hz). SPSS 24.0 was used to perform Pearson's correlation coefficient and simple regression analysis, and the statistically significance level was set to .05. Results: As a result of analyzing the correlation between CoP variables and the putter head rotation angle, the CoP moving length, CoP moving range (ML direction), and CoP moving velocity (ML direction) showed a positive correlation with the putter head rotation angle (yaw axis) and were statistically significant. Conclusion: Therefore, In order to perform the accurate putting stroke maintaining the ball's directionality, it is determined that it is important to control posture sway in the ML directions by minimizing the movement and velocity of the CoP.