• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.3
• /
• pp.273-278
• /
• 2012

The use of Al alloys instead of fiber-reinforced plastic(FRP) in ship construction has increased because of the advantages of Al-alloy ships, including high speed, increased load capacity, and ease of recycling. This paper describes the effects of probe diameter on the optimum friction stir welding conditions of 5456-H116 alloy for leisure ship, measured by a tensile test. In friction stir welding using a probe diameter of 5 mm under various travel and rotation speed conditions, the best performance was achieved with a travel speed of 61 mm/min. Using a probe diameter of 6 mm, rotation speeds of 170-210 rpm, and a travel speed of 15 mm/min produced a rough surface and voids because of insufficient heat input produced by the low rotation speed. At 500-800 rpm, chips were observed, although there were no voids, and the weld surface was excellent. However, at 1100-2500 rpm, many chips were produced due to excessive heat input. Heat effects were very evident on the bottom. For a travel speed of 15 mm/min, heat input caused by friction increased as the rotation speed increased. The mechanical characteristics were degraded by accelerated softening due to increasing heat input.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.4
• /
• pp.804-810
• /
• 2017

Distress accidents occur annually by and failure of sea rescue and time delay lead to fatal accident. In the event of maritime distress, most of the equipments used for search and rescue are in responsible for the position of ships. An MOB equipment is a representative equipment for lifesaving and uses AIS communication method. However, the MOB equipment has problems of interference with existing vessel traffic process and it is difficult to apply because there is no proper certification standard. Therefore, this paper proposes a maritime search and rescue supporting system using smartphone. Utilizing the widely constructed IT infrastructure, it collects position information of the fishing boat and leisure ship using GPS embedded in the smartphone. Also the developed system supports to participate in the rescue by sending the information about the occurrence of the survivor in a certain area to the ship operator.

• Journal of Environmental Health Sciences
• /
• v.49 no.4
• /
• pp.190-200
• /
• 2023

Background: Gunsan has been constantly affected by pollutants generated by the Saemangeum development and the construction industry since the completion of the Saemangeum seawall on April 27, 2010. However, there are limitations to its study, such as taking into consideration weather conditions, geographical factors, and foreign inflows. Objectives: In this study, we compared the Existing-CAPSS emissions of Gunsan with Recalculated-CAPSS emissions data to analyze the differences in emissions characteristics by year (2016~2019). Methods: Using Existing data on CAPSS emissions (2016~2019) and Recalculated-CAPSS emissions (2016~2019) for Gunsan, which were Recalculated following the improvement of emissions calculations for 2020, we organized CO, NO_X, SO_X, PM₁₀, VOC_S, and NH₃ emissions by substance and investigated the differences and characteristics of the Recalculated emissions by year. Results: For Re-CO and Re-PM₁₀, the emission characteristics of CO were examined as energy industry combustion and PM₁₀ emission characteristics were examined as ship cargo from non-road transportation sources, as ship leisure sources were excluded from non-road transportation source emissions. Conclusions: Comparing the emissions of Existing-CAPSS and Recalculated-CAPSS in Gunsan, the emissions of Recalculated-CAPSS by substance decreased by 39.76% for CO, 9.98% for PM₁₀, 5.53% for VOC_S, and 9.24% for NH₃, while Re-NO_X increased by 2.86% and Re-SO_X increased by 1.97%. On the other hand, when comparing the emissions characteristics of Existing-CAPSS and Recalculated-CAPSS in Gunsan, Jeonju, and Iksan, the emission characteristics of Re-NO_X, Re-SO_X, Re-VOC_S and Re-NH₃ were similar to those of Ex-NO_X, Ex-SO_X, Ex-VOC_S, and Ex-NH₃. As such, Gunsan, Iksan, and Jeonju, showed differences in the comparison of different emission characteristics due to the geographical characteristics of the region (population, area, topography, weather factors) and the characteristics of the industrial complex (metal, petrochemical).

• Journal of Korean Port Research
• /
• v.11 no.2
• /
• pp.321-337
• /
• 1997

Rapid change in the technological environment of marine transportation and the development of the ocean shipping industry have fostered a revolution in the port system. This in turn has caused major changes in the function and use of port in Korea. Aside from this. Mokpo Port, however continues to decline, because the existing port facilities and related subsystem are already obsolete with no chance of regaining operational effectiveness and treatment for proper implementation. Although a few studies have been done on the Mokpo Port, has not been found, any reseach for the analytical approach to the transportation system of it. This paper aims to make an extensive analysis of the physical distribution system in Mokpo Port focusing on the coordination of subsystems such as navigational aids system, quay handling and transfer system, storage system and inland transport system. The base of introduced simulation tool here is the queueing theory. The overall findings are as follows; 1. Among those vessels called at Mokpo Port in 1994, the average size of oceangoing vessels is 4,922.1 G/T, and the domestic is 317.8 G/T. The average arrival interval and service time of the domestic vessels are 6.0 hours and 24.1 hours respectively marking the berth occupation rate over 100%. Those for oceangoing vessels are 34.5 hours, 120.0 hours and 37.2%. In order to maintainin the berth occupation rate to 70% the capacity considering the 1994 of domestic piers must be extended to 145% and oceangoing vessels must be increased to 165% year called. 2. The capacity of approaching channel is enough to handle the total traffic volume. 3. Tugs are sufficiently being provided to handle all ships requiring their services 4. The capacity of storage and inland transportation systems are sufficient to handle the throughput and the yard stroage utilization rate of No.1 $\cdots$ No.5 is 4.5% and No.6 1S 30% of 1993's. 5. The utilization rate of LLc(Level Looping Crane) and PNT(PNeumaTic) are 2.7% and 18.8%, respectively. Practical solution and proposal for improvement of Transportation System in Mokpo Port are as follows; 1. To avoid the congestion in domestic pier introduction of a new port operation system is necessary allowing the domestic vessel to use the oceangoing pier. 2. To establish the port management information system to improve the efficiency of port operation. 3. To build a new storage system for high valued cargos including modernization of the present storage and handling system. 4. To insure the safety of navigation in approaching channel, The Vessel Traffic System including separation scheme is introduced. 5. To interest enormously on public relation to ship owner's association, shippers and consignees by showing that they can save cost and ship turnaround time in order to promote the call to Mokpo Port. At last, to be strategically change the function of Mokpo Port to the Leisure, Fishing & Ferry as well as Maritime port.

• Corrosion Science and Technology
• /
• v.9 no.1
• /
• pp.48-55
• /
• 2010

The many vessels are built with FRP(Fiber-Reinforced Plastic) material for small boats and medium vessels. However, FRP is impossible to be used for recyclable material owing to environmental problems and causes large proportion of collision accidents because radar reflection wave is so weak that large vessels could not detect FRP ships during the sailing. Hence, Al alloy comes into the spotlight to solve these kinds of problems as a new-material for next generation instead of FRP. Al alloy ships are getting widely introduced for fish and leisure boats to save fuel consumption due to lightweight. In this study, it was selected 6061-T6 Al alloy which are mainly used for Al-ships and carried out various electrochemical experiment such as potential, anodic/cathodic polarization, Tafel analysis, potentiostatic experiment and surface morphologies observation after potentiostatic experiment for 1200 sec by using the SEM equipment to evaluate optimum corrosion protection potential in sea water. It is concluded that the optimum corrosion protection potential range is -1.4 V ~ -0.7 V(Ag/AgCl) for 6061-T6 Al alloy, in the case of application of ICCP(Impressed current cathodic protection), which was shown the lowest current density at the electrochemical experiment and good specimen surface morphologies after potentiostatic experiment for Al-Mg-Si(6061-T6) Al alloy in seawater environment.

• Journal of the Korea Safety Management & Science
• /
• v.19 no.1
• /
• pp.237-243
• /
• 2017

Currently, Korea is actually increasing and increasing demand for leisure such as parts for A/S of automobile parts of the car, as well as trends in borrowing and finished parts are also required a steady increase in automobile traffic daetsu. There is one car and want to be driving a car A/S parts supplier smoothly for many years and that it is often the case if it is not supplied in a timely fashion, it is a reality that many eonseong hear from customers. These symptoms can be confirmed that the logistics systems of a system of selling auto parts supplier but above all a problem for several reasons, which will be considered as areas for improvement should be done urgently. Enterprises internally cooperation automotive supplier, but the need to get out to re-examine urgently complemented by the logistics system of systems to allow better respond to complex environmental changes of our customers grow, and now also the proliferation of small ship-run screen and Darvin, there is increasing distribution and logistics services, including logistics costs as a lack of work force that the company is itgetda can be called by the reality that the chances of getting a lot of jeyakreul own growth. Given this situation, the procurement of logistics enterprises. In-house logistics. Classified as sales logistics examined the long-term improvement of logistics distribution networks based on this part to derive into the problems of logistics and parts distribution system of Korean auto parts dealer.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2009.10a
• /
• pp.241-242
• /
• 2009

There are marry ships and marine structures and also has marry differences on according to the shape and the interval of hulls to the purpose. the multi-submerged body needs appropriate distance between the hulls because of the optimum hull form. thus, through this paper, the flow characteristics behind the multi-submerged body according os the distance ration between the hulls and various angles of attack was conducted.

• Journal of the Institute of Convergence Signal Processing
• /
• v.22 no.3
• /
• pp.134-140
• /
• 2021

This study relates to the development of a wearable device that can identify a personal location using low-power GPS and IMU based on energy harvesting. The energy harvesting technology using a piezoelectric device was applied for the development of personal location identification, and made it possible to acquire precise personal location data using GPS and IMU. As a result of the experiment, it was confirmed that GPS and IMU data were normally received. The personal location identification device can be prepared for an accident by identifying a personal location in a disaster area, etc., and the user will be able to use it easily regardless of time, place, and environment. It is expected that it can be used in various fields such as leisure and health care.

• Journal of Navigation and Port Research
• /
• v.28 no.10 s.96
• /
• pp.899-908
• /
• 2004

The rise of income and introduction of 5 day a week working system give korean people opportunities to enjoy their leisure time. And many korean people have much interest in oceanic sports such as yachting and also oceanic leisure equipments. With the popularization and development of the equipments, the scope of oceanic activities has been expanding in Korea just as in the advanced oceanic countries. However, The current conditions for the sports in Korea are not advanced and even worse than underdeveloped countries. In order to develop the underdeveloped resources of Korean marina, we need to customize the marina models of advanced nations to serve the specific needs and circumstances of Korea As such we have carried out a comparative analysis of how Austrailia, Newzealand, Singapore, japan and Malaysia operate their marina, reaching the following conclusions. Firstly, in marina operations, in order to protect personal property rights and to preserve the environment, we must operate membership and non-membership, profit and non-profit schemes separately, yet without regulating the dress code entering or leaving the club house. Secondly, in order to accumulate greater value added, new sporting events should be hosted each year. There is also the need for an active use of volunteers, the generation of greater interest in yacht tourism, and the simplification of CIQ procedures for foreign yachts as well as the provision of language services. Thirdly, a permanent yacht school should be established, and classes should be taught by qualified instructors. Beginners, intermediary, and advanced learner classes should be managed separately with special emphasis on the dinghy yacht program for children. Fourthly, arrival and departure at the moorings must be regulated autonomically, and there must be systematic measures for the marina to be able, in part, to compensate for loss and damages to equipment, security and surveillance after usage fees have been paid for. Fifthly, marine safety personnel must be formed in accordance with Korea's current circumstances from civilian organizations in order to be used actively in benchmarking, rescue operations, and oceanic searches at times of disaster at sea.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.5
• /
• pp.566-573
• /
• 2017

The chine of high speed vessels does not only play a role in changing position when planing but also helps balancing the hull. It also has a great influence on resistance performance. However, designing a chine requires a lot of experience because it is influenced by various factors such as displacement, transom shape, draft and width. Such a design is not based on an empirical formula, but the purpose of this study is to provide basic guidelines regarding the shape of chine through calculation. This design was developed using Yacht-one, a commercial design program, and analysis was performed using Star-CCM+, also a commercial analysis program. Analysis of the hull selected in this study was carried out by Dynamic Fluid Body Interaction (DFBI) method. Analysis of the chine was carried out at chine angles of 15, 16, 17, and 19degrees, at a speed of 30knots. The result indicated that the highest trim occurred at 16 degrees among the four chine angles considered, and the highest heave occurred at 15degree. In terms of resistance performance, minimum resistance was observed at 16 degrees. Consequently, for minimum ship resistance, it is necessary to complete calculations in accordance with the chine angles, ${\pm}2$ degrees from the initial chine angle, which should be carried out a the design stage.