• The Journal of the Korean dental association
• /
• v.44 no.2 s.441
• /
• pp.115-122
• /
• 2006

Objective : The purpose of this study was to evaluate the dimensional errors between real tooth, 3D CT image and CARP model. Materials and Methods : Two maxilla and two mandible block bones with intact teeth were taken from two cadavers. Computed tomography was taken either in dry state and in wet state. After then, all teeth were extracted and the dimensions of the real teeth were measured using a digital caliper at mesio-distal and bucco-lingual width both in crown and cervical portion. 3D CT image was generated using the V-works $4.0^{TM}$ (Cybemed Inc., Seoul, Korea) software. Twelve teeth were randomly selected for CARP model fabrication. All the measurements of 3D Ct images and CARP models were made in the same manner of the real tooth group. Dimensional errors between real tooth, 3D CT image model and CARP model was calculated. Results : 1) Average of absolute error was 0.199 mm between real teeth and 3D CT image model, 0.169 mm between 3D CT image model and CARP model and 0.291 mm between real teeth and CARP model, respectively. 2) Average size of 3D CT image was smaller than real teeth by 0.149 mm and that of CARP model was smalier than 3D CT image model by 0.067mm. Conclusion : Within the scope of this study, CARP model with the 0.291 mm average of absolute eror can aid to enhance the success rate cf autogenous tooth transplantation due to the increased accuracy of recipient bone and donor tooth.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.68.2-68.2
• /
• 2017

인체접촉시 니켈도금의 알러지 반응을 억제하기 위한 대체 도금기술인 비 시안계 Cu-Sn 합금도금을 개발함에 있어서, 황산구리5수화물과 황산제일주석을 금속염으로 하여 황산 및 계면활성제, 유화제 등을 포함한 각종 유기첨가제를 포함하였고 특히 은백색조의 외관 색상과 안정적인 Cu-Sn 합금전착을 위해 2종의 착화제인 EDTP (Ethylenediaminetetrapropanol, $C_{14}H_{32}N_2O_4$)와 TEA (Triethanolamine)를 첨가한 비 시안계 Cu-Sn 합금 도금액을 도출하였다. Cu-Sn 합금도금 피막 조성의 균일화를 도모하기 위해서는 합금 도금액중의 Cu와 Sn 금속이온 농도를 일정하게 유지하는 것이 필요하다. 그러나 합금 도금액 중 2가 주석이온($Sn^{2+}$)은 수용액 중에서 4가 주석이온($Sn^{4+}$)으로 산화됨으로써 도금액 색상이 백탁이 되고 Stannic Hydroxide($Sn(OH)_4$, $SnO_2{\cdot}2H_2O$)이 생성되어 대량의 침전물이 침강하는 문제점이 발생되는 등시간 경과에 따른 도금액의 경시 변화가 발생되었다. 상기 침전물은 연속여과에 의해 제거 가능하나 합금 도금액 중 $Sn^{2+}$ 농도가 지속적으로 감소하게 된다. 이는 합금 도금액 중 금속이온 비율이 변동함으로써 합금도금 피막의 조성비를 일정하게 유지하는 것이 곤란해진다. 이에 $Sn^{4+}$ 침전물 생성을 방지하기 위한 산화방지제를 개발하고 또한 산화방지제의 첨가에 따른 도금 피막 외관에 미치는 영향을 평가하여 외관 개선을 위한 광택제를 개발하고자 한다. 본 연구의 결과를 토대로 니켈도금과 동등 이상의 기능 특성을 갖는 비 시안계 Cu-Sn 합금도금액을 개발하여 실용화하는 것을 목적으로 하였다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.05a
• /
• pp.976-979
• /
• 2008

As internet occupies a great deal of portion in our life, a lot of mental diseases become the points at issue relating to internet addiction. The purpose of this study is to examine whether internet addiction is related with Attention Deficit Hyperactivity Disorder that is characterized with sustained inattention, hyperactivity and impulsivity and then find out which sub-factors of internet addiction are influencing effective on Attention Deficit Hyperactivity Disorder. As result of applying reliability analysis, frequency analysis, cross tabulation analysis, t-test, ANOVA, Pearson's correlation analysis and multiple regression analysis, it shows the following research results.

• Journal of Information Display
• /
• v.2 no.3
• /
• pp.72-77
• /
• 2001

Amorphous silicon thin-film transistors (a-Si TFTs) were incorporated into Mo-tip-based triode-type field emitters and diode-type ones of carbon nanotubes for an active-matrix cathode (AMC) plate of field emission displays. Also, we developed a novel surface-treatment process for the Mo-tip fabrication, which gleatly enhanced in the stability of field emission. The field emission currents of AMC plates on glass substrate were well controlled by the gate bias of a-Si TFTs. Active-matrix field emission displays (AMFEDs) with these AMC plates were demonstrated in a vacuum chamber, showing low-voltage matrix addressing, good stability and reliability of field emission, and highly uniform light emissions from the anode plate with phosphors. The optimum design of AMFEDs including a-Si TFTs and a new light shield/focusing grid is discussed.

• Journal of the Korea Institute of Building Construction
• /
• v.5 no.1 s.15
• /
• pp.69-74
• /
• 2005

The construction of house in Korea firstly has been made up quantitative supply and margin of confined land until the latest. But, residents interest of living environment, demand of high-quality has varied with the latest elevation of life quality Specially, the interest for environment-friendly architecture is increased by the recent well-being trend in 2002, So, construction company and construction materials manufacturing industry are trying to offer more healthy and agreeable indoor aerial environment. Related circles do their best to commercialize and develop environment-friendly finish materials which influence indoor aerial environment. Therefore, in this study, that developing raw material and productive system that can minimize hazardous article quality discharge with formaldehyde in development of correction of deformities board such as plywood that is used mainly by a environment-friendly materials indoor finish, and examines application possibility of construction correction of deformities board through properties of matter examination by purpose, do.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.377-383
• /
• 2011

The paper is to perceive accurately speed of the train through redundant processor operation. When Slip/slide is occurred at the axle, the train is applied brake force using the Tachometer and the Doppler sensor which assistance equipment. One of the main features of railway signaling system is that rolling stock is made stop to avoid collision with the rolling stock ahead when the rolling stock exceeds its maximum operating speed in line. In addition, in the case of the rolling stock with automatic train operation, it carries out activities such as braking and propulsion using the difference between its actual speed and target speed at the point. To perform these functions, it is essential to calculate the exact speed of the rolling stock in signaling equipment on vehicles. Train speed detection unit are composed of the Tachometer and the Doppler sensor, and speed information is sent to the SDU unit. The processor of SDU unit calculates the speed of the train using compare logic the received speed information. Even if there are Slip/Slide, signaling system is available to apply exact braking, to improve stop on position and to guarantee the safety of trains.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.145-153
• /
• 2011

In the system necessary for safety such as the train control system, to make train control information be sent correctly is very important to enable organic movement between trains. In the case of the system such as RF-CBTC (Radio Frequency Communication Based Train Control) the control related information is sent through wireless transmission between on-board system of a train and wayside transmitter. The wayside transmitter collects the running information such as location, velocity from the on-board system and operates the optimizing control by sending the control information such as the target, limited velocity to the on-board system. But, when the communication disconnect or train failure, the critical hazard such as train collision or derailment may be possible because the RF-CBTC depends on the information through wireless communication. This paper discribes of performing Fall-Back system to detect train position in the case of rail break or communication failure to avoid train accident and allows train to be operated safely. It can be implemented with ATP function through track circuits using active-type transformers and axle counters, and allows train to be operated manually in emergency status.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.246-246
• /
• 2012

최근의 디스플레이 시장에서는 고효율 저전력, 자발광 소자인 OLED가 차세대 디스플레이 시장의 블루칩으로써 연구되고 개선되어 왔다. 고효율, 고휘도 구현이 가능한 OLED 소자는 초기 발광 시 수명감소, 저전류 구동 효율 개선 및 소자의 유기 재료 개선의 문제점에 직면해 있기 때문에 많은 가능성을 아직 현실화 하지 못하고 있다. 본 연구에서는 전기적 스트레스를 가한 OLED 소자의 전기적, 광학적 성질을 측정함으로써 열화에 따른 소자의 특성 변화를 확인하여 문제점을 개선하는데 기여하고자 한다. $2{\times}2$ inch Glass에 $2{\times}2$ mm 크기의 발광면적을 갖는 Red OLED 소자를 제작한 후 Source Measure Unit을 이용, 8 V의 과전압을 72시간 동안 인가하여 소자의 열화현상을 가속시켰다. 이후 I-V-L 장비를 이용하여 전기적 특성 및 휘도 특성을 측정하였다. 측정된 결과는 휘도가 8 V에서 10,620 cd/$m^2$ ＞ 9,849 cd/$m^2$ (약 7.2% 감소)로 변화한 것을 확인 하였으며, 휘도 효율과 전력 효율을 측정해본 결과 8 V 에서의 소비전력 효율 역시 16%에서 ＞ 15%로(약 1%감소) 변화하였으나 안정적으로 발광이 유지되는 3 V~6 V 구간에서는 효율이 약 13%가 감소하였다. 또한 휘도 효율은 8 V 기준으로 1% , 3 V~6 V 구간에서는 약 8% 감소하였다. 본 연구 결과를 통하여 OLED 소자의 열화 현상은 소자의 휘도 감소뿐만 아니라 소비전력증가, 열화현상의 촉진으로 이어지는 것으로 확인 되었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.199-199
• /
• 2009

Recently, polymeric microlens arrays have become important elements in many applications. Microlens arrays have been used to enhance luminance efficiency and luminance power efficiency of light-emitting diodes (LEDs) and organic LEDs. Many processes for fabrication of microlens array are studied. Though the MLA has been fabricated by electroformed mold, LIGA process and reflow method, these methods were required masks, multiple process steps and post processing. In this paper, we proposed rapid and direct UV laser direct fabrication process using colorless liquid photopolymer, NOA60 for polarization activated microlens. The microlens arrays are formed on the NOA60 on glass, after the focused laser energy was irradiated to the material. The diameter of MLA was varied from 42 to 88 ${\mu}m$, and the height from 0.9 to 1.6 ${\mu}m$. The MLA fabricated using NOA60 shows more then 85% transmittance as well as good hardness for optical module.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.215.2-215.2
• /
• 2016

플라즈마는 현대 산업에서 다양한 고부가가치 산업 분야에 걸쳐 이용되고 있다. 이러한 플라즈마를 정밀하게 진단하고 제어하는 기술이 공정의 수율을 증대하고 생산성을 높이는데 크게 기여함은 자명하다. 플라즈마를 진단하는 방법은 크게 광학적 진단 방법과, 전기적 진단 방법으로 나눌 수 있는데 광학적 진단 방법은 방전시 발생하는 방출광을 통해 플라즈마의 현재 상태를 예측하는 방법이고, 전기적 진단 방법은 플라즈마 내로 직접 탐침을 접촉하여 전기적 물리량을 측정하는 방법이다. 각각은 정성적, 정량적 진단을 하는 데에 장점이 있다. 공정 모니터링은 주로 광학적 진단 방법에 의해 이루어지는데 전기적 진단 방법은 플라즈마와 직접 접촉하기 때문에 플라즈마에 대한 간섭현상이 발생하므로 부적합하다. 해당 실험에서는 유도 결합형 플라즈마 발생 용기에 아르곤, 산소 혼합 유체를 유입하여 방전하며 광학적 진단 방법을 통해 플라즈마를 관측하며 실험을 진행하였다. 측정 장치는 3채널 광학 진단이 가능한 시스템을 구성하여 공정중 발생하는 방출광의 특정 피크 변화를 공정 변수 변화로 인지하여 질량 유량 제어기를 조작, 피크를 초기상태로 되돌리는 공정 제어가 가능하도록 시스템을 구성하였다. 이를 통해 플라즈마를 이용한 공정 중 공정 변화에 자동으로 대응하는 공정제어 시스템을 시험 하였다.