• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.79-81
• /
• 1996

We fabricated SrTiO$_3$thin film capacitor on the Ag/Si-wafer by RF sputtering deposition. And I-V characteristics and structual analysis of the thin film capacitor are investigated. We found that the leakage current of the films during deposition is strongly denpent on the ambient gas and substrate temperature. Because of increase of activation energy, leakage current increased at high temperature and resistivity of the films was decreased. According to the increase of oxygen gas flow rate, the conductivity of thin film capacitor was increased and leakage current was decreased.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.4
• /
• pp.263-268
• /
• 2001

This paper describes the effects of applied bias conditions on electrochemical etch-stop characteristics. THere are a number of key issues such as diode leakage and ohmic losses which arise when applying the conventional 3-electrochemical etch-stop to fabricated some of he MEMS(microelectro mechanical system) and SOI(Si-on-insulator) structures which employ SDB(Si-wafer direct bonding). This work allows to perform anin situ diagnostic to predict whether or not an electrochemical etch-stop would fail due to diode-leakage-induced premature passivation. In addition, it presents technology which takes into account the effects of ohmic losses and allows to calculate the appropriate bias necessary to obtain a successful electrochemical etch-stop.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1452-1454
• /
• 1997

Properties of flashover in polymer insulators are very important under pollution environments. It is necessary to analyse flashover characteristics whether insulators are still safe or not. A lot of precious information can be got out of polluted polymer insulators through leakage current measurement. The behavior of partial arc discharge leads to flashover directly. It is possible to measure partial arc discharge as leakage current pulses analysis. The shape of histogram reflects degree of pollution, wetting and voltage stress level. It can be expressed by Weibull distribution function.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.71-74
• /
• 1998

In this Paper, we investigate the electrical properties of ultra-thin(70${\AA}$) nitrided(NO) and reoxidized nitrided oxide(ONO) film that ale considered to be premising candidates for replacing conventional silicon dioxide film in ULSI level integration. we studied I$\sub$g/-V$\sub$g/ characteristics to know the effect of nitridation and reoxidation on the current conduction, leakage current time-dependent dielectric breakdown(TDDB) to evaluate charge-to-breakdown(Q$\sub$bd/), and the effect of stress temperature(25, 50, 75, 100$^{\circ}C$) and compared to those with thermal gate oxide(SiO$_2$) of identical thickness. From the measurement results, we find that reoxidized nitrided oxide(ONO) film shows superior dielectric characteristics, leakage current, and breakdown-to-charge(Qbd) performance over the NO film, while maintaining a similar electric field dependence compared to NO layer. Besides, ONO film has strong resistance against variation in temperature.

• Transactions on Electrical and Electronic Materials
• /
• v.4 no.6
• /
• pp.32-37
• /
• 2003

In this paper, the trap characteristics of thin silicon oxides is investigated in the ULSI implementation with nano structure transistors. The stress and transient currents associated with the on and off time of applied voltage were used to measure the distribution of high voltage stress induced traps in thin silicon oxide films. The stress and transient currents were due to the charging and discharging of traps generated by high stress voltage in the silicon oxides. The transient current was caused by the tunnel charging and discharging of the stress generated traps nearby two interfaces. The stress induced leakage current will affect data retention in electrically erasable programmable read only memories. The oxide current for the thickness dependence of stress current, transient current, and stress induced leakage currents has been measured in oxides with thicknesses between 113.4nm and 814nm, which have the gate area 10$\^$-3/ $\textrm{cm}^2$. The stress induced leakage currents will affect data retention, and the stress current and transient current is used to estimate to fundamental limitations on oxide thicknesses.

• Smart Structures and Systems
• /
• v.16 no.1
• /
• pp.213-222
• /
• 2015

Early detection and precise location of leakage is of great importance for life-cycle maintenance and management of municipal pipeline system. In the past few years, acoustic emission (AE) techniques have demonstrated to be an excellent tool for on-line leakage detection. Regarding the multi-mode and frequency dispersion characteristics of AE signals propagating along a pipeline, the direct cross-correlation technique that assumes the constant AE propagation velocity does not perform well in practice for acoustic leak location. This paper presents an improved cross-correlation method based on wavelet transform, with due consideration of the frequency dispersion characteristics of AE wave and the contribution of different mode. Laboratory experiments conducted to simulate pipeline gas leakage and investigate the frequency spectrum signatures of AE leak signals. By comparing with the other methods for leak location identification, the feasibility and superiority of the proposed method are verified.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.16 no.2
• /
• pp.25-34
• /
• 2020

As leakage in nuclear power plants could cause a variety of problems, it is very critical to monitor leakage from the safety point of view. Accordingly, a new type of leak detection system is currently being developed and flow characteristics of the sampling and transportation system are investigated by using numerical analysis as a part of the development process in this study. The results showed that the steam mass fraction varied according to the effect of the gap between the insulation and piping component, transportation velocity, and material properties of porous media during the sampling and transportation process. The results of this study should be useful for understanding flow characteristics of the sampling and transportation system and its design and application.

• Tribology and Lubricants
• /
• v.26 no.4
• /
• pp.230-239
• /
• 2010

Mechanical face seal installed in boiler feedwater pump prevents leakage of working fluid using thin fluid film between stator and rotor. If the leakage of working fluid exceeds the allowable volume, serious malfunction of boiler feedwater pump will be happen. The thinner fluid film exists between stator and rotor, the less working fluid leaks out. However, if the thickness of fluid film is not enough, the wear of seal face will be increased. And it causes the decrease in life of mechanical face seal. Therefore appropriate design is necessary to maximize the performance and life of mechanical face seal. In this study, numerical analysis using finite volume method was conducted to investigate the static characteristics of wavy mechanical face seals which have 4 different wavy surface profiles on rotor. As a result, opening force, leakage volume of working fluid and friction torque were obtained. For the same minimum film thickness, the static characteristics of mechanical face seal were affected by the wavy surface profile which can change the thickness of working fluid film and pressure distribution.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.10
• /
• pp.82-88
• /
• 2007

This paper presents the thermal and electrical characteristics of ZnO arrester blocks under the AC voltages. The leakage currents of ZnO arrester blocks were measured as a function of the time. The temperature distributions of ZnO arrester blocks were observed by the thermal image infrared camera. The degradation and thermal runaway of ZnO arrester blocks were closely related to the temperature limit of ZnO arrester blocks which being decided heat generation and dissipation. The temperature and leakage current of ZnO arrester blocks were sensitively changed in a resistance of ZnO arrester blocks. As a result, the degradation and thermal runaway of ZnO arrester blocks depend on the temperature and leakage current of ZnO arrester blocks.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2007.09a
• /
• pp.528-541
• /
• 2007

To get the possible for management and maintenance, it was analyzed the deformation characteristics, such as crest of embankment and concrete face slab, and leakage of concrete faced rockfill dams (CFRD). There are trends that embankment deformation depends on intact strength used rockfills rather than dam height, deformation normal to concrete face slab during the first reservoir filling is occurred more than 80% of the total deformation in general, and the magnitude and trend of concrete face slab deformation is similar to post-construction crest settlement. The results showed that the range of post-construction crest settlement suggested by Sherard and Cooke (1987), and Clements (1984) had a good agreement in the cases using rockfill with very high intact strength, but it had a trend which underestimated crest settlement in the cases using rockfill with medium to high intact strength. The maximum leakage rate in general was observed during the first reservoir filling and long-term leakage rate was rapidly increased when the dam height exceeds approximately 120m.