• Journal of Biosystems Engineering
• /
• 제33권4호
• /
• pp.224-229
• /
• 2008

This study was aimed to minimize the impact force and vibration transmitted to the transporting materials from the trailer and wheel shaft by installing the leaf spring suspension device at the space between the wheel shaft and frame of power tiller trailer. The developed trailer equipped with leaf spring suspension device was compared to the existing trailer without suspension device, in order to identify the vibration absorption effect of the leaf spring. The results of this study could be summarized as follows; (1) The length and the maximum bending amount of the leaf spring were designed as 1,000 mm and 42 mm, respectively, considering the possible space for installing at below the trailer. When 4 leaf springs were installed on both wheel shafts, the allowable maximum load was identified as 9,418 N. (2) The average vibration accelerations for the frequency less than 20 Hz, where the severe transporting loss could be represented, were $0.017\;m/s^2$ and $0.133\;m/s^2$ for the developed and the existing trailer, respectively, showing the vibration absorption effect of about 87%. And the average vibration accelerations on the driver's seat for the frequency less than 20 Hz were $0.01\;m/s^2$ and $0.20\;m/s^2$ for the developed and the existing trailer, respectively, which showed the similar vibration absorption effect. (3) The change of the average vibration accelerations for the frequency from 20 Hz to 80 Hz showed the similar tendency with the result for the frequency less than 20 Hz, but the effect for developed trailer was reduced slightly. And the effect of vibration absorption for the above 80 Hz was reduced highly. However, by installing the leaf spring suspension device at the trailer, the low frequency below 40 Hz, which could affect on transporting loss severely, could be reduced highly. (4) The maximum vibration acceleration for the frequency less than 20 Hz were $0.027\;m/s^2$ and $1.267\;m/s^2$ for the developed and the existing trailer, respectively. And the change of maximum acceleration between 20 Hz and 120 Hz was showed similar tendency with the result for the frequency less than 20 Hz, but the width of change was reduced highly.

• Journal of Biosystems Engineering
• /
• 제37권6호
• /
• pp.359-364
• /
• 2012

Purpose: This study was conducted to analyze the vibration absorption effect for the agricultural product transportation-trailer equipped with vibration absorbable connecting hitch, leaf spring suspension, and shock absorber simultaneously (HLS), comparing with the trailer equipped with vibration absorbable connecting hitch only(H), trailer equipped with connecting hitch and leaf spring suspension (HL), and existing trailer with no vibration absorption device (E). Methods: Vertical accelerations were measured at driver seat and front, middle, rear parts of trailer bottom with no load for 4 types of transportation-trailer, and analyzed using FFT analyzer. Results: The magnitude of average vibration accelerations occurred up to 20 Hz, at this low frequencies the severe damage for agricultural products could be represented, was lower (maximum 6 times) for HLS trailer compared with H trailer. And vibration absorption effect for HLS trailer was also higher up to 40-80 Hz and 80-100 Hz, but the difference was less. At driver seat, the vibration absorption effect was high severely for HL and HLS trailer, and the magnitude of vibration acceleration was showed less difference in comparing at trailer bottom. Conclusions: From the test results, it could be recommended that the agricultural products transportation trailer should be equipped with vibration absorption device of HLS.

• 드라이브 ㆍ 컨트롤
• /
• 제18권2호
• /
• pp.38-45
• /
• 2021

In recent years, the demand for an onboard scale system which can directly monitor load distribution and overload of vehicles has increased. Depending on the suspension type of the vehicle, the onboard scale system could use different types of sensors, such as, angle sensors, pressure sensors, load cells, etc. In the case of a vehicle equipped with leaf spring suspension system, the load of the vehicle is measured by using the deflection or displacement of the leaf spring. Leaf springs have hysteresis characteristics that vary in displacement depending on the load state. These characteristics cause load measurement errors when moving or removing cargoes. Therefore, this study aimed at developing an onboard scale device for cargo vehicles equipped with leaf springs. A sectional modeling method which can reduce measurement errors caused by hysteresis characteristics was also proposed.

• 생물환경조절학회지
• /
• 제21권4호
• /
• pp.437-444
• /
• 2012

본 연구에서는 현제 농가에서 사용하고 있는 진동흡수장치가 전혀 없는 트레일러(E)와 트레일러의 적재규격에 적합하게 평판스프링과 쇽업쇼바를 동시에 설계 제작한 트레일러(I)를 사용하였다. 트레일러에 360kg의 배를 4층으로 적재한 상태로 아스팔트 도로 위를 2m/s로 정속 주행하면서 발생된 평균 진동 주파수의 크기를 상호 비교하여 개발된 트레일러의 진동흡수 효과를 비교 분석하였다. 개발한 현가장치를 장착한 개량된 트레일러는 60Hz 이하와 80Hz 이하의 주파수에서 기존 트레일러에 비해 진동 가속도의 감소 효과가 매우 크게 나타났다. 기존 트레일러에 비하여 개량된 트레일러에서 평균 진동가속도의 크기는 주파수 영역에 따라서 다르긴 하지만 3분의 1까지 대폭 감소시킬 수 있었다. 후방의 상층에 적재된 농산물일수록 진동가속도의 크기가 높아 부패가 빨리 진행 된다고 보고된 논문과 일치하지 않는 이유는 전 연구자는 적재함의 길이가 14,000mm이었고 본 시험에서 사용한 적재함은 1,820mm로 비교적 짧은 것에서 얻어진 결과로 일정한 경향을 찾기가 어려웠던 것으로 판단된다. 모든 주파수의 영역에서 개량된 트레일러가 기존의 트레일러에 비하여는 진동가속도의 크기가 현저히 낮게 나타났다. 특히 40Hz에서 80Hz까지의 주파수대에서 3분의 1로 진동가속도의 크기를 줄일 수 있어서 농산물의 수송 손실을 대폭 감소시킬 수 있을 것으로 판단된다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.750-755
• /
• 2005

This paper proposes a small VCM (Voice coil motor) type actuator using curved suspensions for auto-focusing and zoom motions for mobile information devices. 1'he proposed focusing actuator adopts a nontraditional type of suspension using curved beams in order to extend output displacement within small height restriction. The curved beam is similar to the leaf spring type which is usually used in optical disk drives. In addition, three different materials are considered for the curved suspension model, and Aluminum shows the best dynamic characteristics. The proposed zoom actuator does not use a suspension supporting bobbin but a moving rail and a sloper mechanism by generating rotational force at lens holder. The sensitivity of design parameters on output performance is studied using ANSYS (3D FEM tool). Experiments using a prototype of the proposed actuator model verified the analytical prediction and performance.

• 드라이브 ㆍ 컨트롤
• /
• 제18권1호
• /
• pp.9-16
• /
• 2021

Overloaded vehicles increase the maintenance cost of road structures, and they are a major factor in causing damage to the roads and bridges. In addition, overloaded vehicles compromise the braking capability of the vehicle; thus, threatening the safety of the driver. In order to prevent overloading of vehicles, the government is cracking down on the roads by using a device that measures the weight of vehicles. But this process is inconvenient because the place where the equipment is installed is far away from where the cargo is loaded. Due to the limitations of these fixed weighing devices, there is a growing need for technology that can monitor vehicle weight distribution and overload conditions in real time. In this work, we develop an onboard scale that can measure the load (weight) of trucks in real time. The onboard scale consists of high sensors, a signal processing unit, and a display, and it measures the load using height-displacement of the vehicle's leaf spring suspension.

• 한국소음진동공학회논문집
• /
• 제18권1호
• /
• pp.11-19
• /
• 2008

This paper proposes small VCM(voice coil motor) type, auto-focusing and zoom actuators for mobile information devices. In order to meet the large output displacement within small height restriction, the proposed auto-focusing actuator adopts curved suspensions, which are similar to a leaf-spring type suspension of optical disk drives. The sensitivity of design parameters on output displacement and dynamic performance is implemented using ANSYS (3D FEM tool) to determine the optimal geometry and stiffness of the curved suspensions. This paper also investigates a new zoom actuator without a suspension supporting a bobbin. The zoom actuator uses a moving rail and a stoper mechanism by generating rotational force at lens holder. Magnetic flux density of the zoom actuator are calculated by both the FEM and permeance method. Experiments using prototypes of the proposed focusing and zoom models show that both actuators meet the required displacement and performance.

• Design & Manufacturing
• /
• 제13권1호
• /
• pp.55-60
• /
• 2019

Smart-phone in the recently released high-end applied to the camera module is equipped with the most features auto focusing camera module. Also, auto focusing camera module is divided into voice coil motor, encoder, and piezo according to type of motion mechanism. Auto focusing camera module is composed of voice coil motor (VCM) as an actuator and leaf spring as a guide and suspension. VCM actuator is made of magnet, yoke as a metal, and coil as a copper wire. Recently, the assembly as yoke and magnet is made by human resources. These process has a long process time and it is difficult to secure quality. Also, These process is not economical in cost, and productivity is reduced. Therefore, an automatic assembly as yoke and magnet is needed in the present process. In this paper, we have developed an automatic assembly device that can automatically assemble yoke and magnet, and performed verifying performance. Therefore, by using the developed automatic assembly device, it is possible to increase the productivity and reduce the production cost.