• The Korean Journal of Health Service Management
• /
• v.10 no.4
• /
• pp.61-73
• /
• 2016

Objectives : The aim of this study was to investigate the satisfaction determinants of rehabilitation care group inpatients in rehabilitation long-term care hospitals. Methods : A survey was conducted with 262 patients from 6 rehabilitation long-term care hospitals located in Busan Kyungnam. Data were collected from June 2016 to July 2016 with a structured questionnaire and analyzed with SPSS 23.0. Results : The significant factors affecting the overall satisfaction score were disease group and 5 quality indices of medical services(Medical service quality, Rehabilitation services quality, Hospital reputation, External physical environment, and Internal physical environment). Additionally, the significant factors affecting intention to revisit were age, disease group, length of hospital stay and the 5 quality indices of medical services. Conclusions : The results of this study indicate that rehabilitation long-term care hospitals should try to improve the overall satisfaction of inpatients, especially focusing on the internal physical environment and the quality of the rehabilitation services and medical services, which will lead to a high level of intention for patients to revisit.

• Journal of Korea Foundry Society
• /
• v.30 no.6
• /
• pp.210-216
• /
• 2010

The aim of this study is to characterize a thixoextruded 7075 Al wrought alloy bar in terms of its isotropic behavior through the optical microscope, mechanical test and electron back scattered diffraction. It is also discussed of the extrudability improvement for 7075 Al wrought alloy by thixoextrusion, with emphasis on controlling thixoextrusion parameters. Hot extrusion shows that the maximum extrusion pressure depends on their characteristics in terms of flow stress and hot workability. In the contrary, thixoextrusion demonstrates that the maximum extrusion pressure is almost uniform regardless of the experimental parameters, such as initial ram speed, die bearing length and thixoextrusion temperature. The hot extruded microstructures become elongated to extrusion direction, while the thixoextruded microstructures are isotropic and homogeneously distributed due to the existence of liquid phase between solid grains during the process. The grain refinement due to dynamic recrystallization during thixoextrusion has been also occurred. Subsequent recrystallization would lead to the strengthening of mechanical properties, as observed in the study. The important point is that the values of tensile, yield strength and elongation of the thixoextruded bar without plastic deformation are similar to those of the hot extruded bar with severe plastic deformation.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.341-348
• /
• 2009

Various types of micro cone penetrometers have been developed by using strain gages for the layered soil detection. Strain gages, however, are affected by several factors such as temperature, self heating and lead wire length. In this study, micro cone penetrometers with 3~7mm in diameter, are developed by using FBG sensor to overcome the defects of the strain gage, and compensate the effect of temperature during penetration. In order to verifiy the accuracy and reliability of the developed FBG cone, the cone penetration test is performed on the layered soil. The tip resistance of FBG snesor shows excellent sensitivity, and can detect the interface of the layered soils with higher resolution. In addition, the 3mm micro cone penetrometer which is impossible cone diameter by using strain gages presents much higher sensitivity than the 7mm cone penetrometer. This study suggests that FBG sensor is a useful sensor for manufaturing the ultra small sized cone, and effectively detects the interface of the layered soil.

• Journal of The Korean Astronomical Society
• /
• v.37 no.4
• /
• pp.225-232
• /
• 2004

Shocks are ubiquitous in astrophysical environments and cosmic-rays (CRs) are known to be accelerated at collisionless shocks via diffusive shock acceleration. It is believed that the CR pressure is important in the evolution of the interstellar medium of our galaxy and most of galactic CRs with energies up to ${\~}\;10^{15}$ eV are accelerated by supernova remnant shocks. In this contribution we have studied the CR acceleration at shocks through numerical simulation of 1D, quasi-parallel shocks for a wide range of shock Mach numbers and shock speeds. We show that CR modified shocks evolve to time-asymptotic states by the time injected particles are accelerated to moderately relativistic energies, and that two shocks with the same Mach number, but with different shock speeds, evolve qualitatively similarly when the results are presented in terms of a characteristic diffusion length and diffusion time. We find that $10^{-4} - 10^{-3}$ of the particles passed through the shock are accelerated to form the CR population, and the injection rate is higher for shocks with higher Mach number. The time asymptotic value for the CR acceleration efficiency is controlled mainly by shock Mach number, and high Mach number shocks all evolve towards efficiencies ${\~}50\%$, regardless of the injection rate and upstream CR pressure. We conclude that the injection rates in strong quasi-parallel shocks are sufficient to lead to significant nonlinear modifications to the shock structures, implying the importance of the CR acceleration at astrophysical shocks.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.12
• /
• pp.1335-1340
• /
• 2003

In this paper, a single balanced diode Mixer for the homodyne FMCW radar to detect distance and velocity of a vehicle target is designed and implemented using a microstrip line and two schottky barrier beam lead diodes. This mixer is optimally designed to have less a conversion loss within the 100 MHz bandwidth with a little LO injection power and a higher LO isolation as soon as possible through the embedded electrical length of microsrtrip line placed between the coupler and diode matching, considering together LO matching condition. The measured results show 6 dB of conversion loss, 23 dB LO/RF isolation and 3 dBm of input 1l dB, respectively.

• Carbon letters
• /
• v.8 no.1
• /
• pp.12-16
• /
• 2007

Molecular sieving carbon (MSC) for separating $O_2-N_2$ and $CO_2-CH_4$ has been prepared through chemical vapor deposition (CVD) of methane and benzene on activated carbon spheres (ACS) derived from polystyrene sulfonate beads. The validity of the material for assessment of molecular sieving behavior for $O_2-N_2$ and $CO_2-CH_4$ pair of gases was assessed by the kinetic adsorption of the corresponding gases at $25^{\circ}C$. It was observed that methane cracking on ACS lead to deposition of carbon mostly in whole length of pores rather than in pore entrance, resulting in a reduction in adsorption capacity. MSC showing good selectivity for $CO_2-CH_4$ and $O_2-N_2$ separation was obtained through benzene cracking on ACS with benzene entrantment of $0.40{\times}10^{-4}\;g/ml$ at cracking temperature of $725^{\circ}C$ for a period of 90 minutes resulting in a selectivity of 3.31:1.00 for $O_2-N_2$ and 8.00:1.00 for $CO_2-CH_4$ pair of gases respectively.

• Korean Journal of Bronchoesophagology
• /
• v.6 no.2
• /
• pp.177-180
• /
• 2000

Backgrounds： Patients with respiratory failure may require prolonged mechanical ventilation. The purpose of this study was to determine the optimal time for tracheostomy and complications of tracheostomy. Methods : All medical records of 27 patients who underwent tracheostomy in department of thoracic & cardiovascular surgery at Yondong Severance hospital between January 1, 1990 and December 31, 1998, were reviewed. Variables analyzed include underlying disease, primary indication of tracheostomy, interval from 1st intubation to tracheostomy, duration from tracheostomy to weaning ventilator, duration of decannulation, and complication. There were 18 men and 9 women. Mean age at the time of the tracheostomy was 54 years (rage, 11 to 64 yeras). Results : Underlying diseases included lung cancer in 14 patients (51.9%), trauma in 8 patients (29.6%), and TE fistula in 2 patients. The indication for tracheostomy were as follows: prolonged mechanical ventilation in 13 patients, purpose of bronchial toilet in 9 patients, and tracheal stenosis in 5 patients. The mean interval between the first intubation and tracheostomy was 8.1 days. The mean duration from tracheostomy to weaning ventilator was 10.1 days. Conclusions : Timing of tracheostomy Is very important. Tracheostomy may benefit patients because it can accelerate the process of weaning and thus lead to a reduction in the duration of ventilation, length of hospitalization, and cost.

• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.2
• /
• pp.93-102
• /
• 2018

Quantitative Risk Assessment (QRA) has been used in shipping and offshore industries for many years, supporting the decision-making process to guarantee safe running at different stages of design, fabrication and throughout service life. The assessments of a risk perspective are informed by the frequency of events (probability) and the associated consequences. As the number of offshore platforms increases, so does the length of subsea pipelines, thus there is a need to extend this approach and enable the subsea industry to place more emphasis on uncertainties. On-board operations can lead to objects being dropped on subsea pipelines, which can cause leaks and other pipeline damage. This study explains how to conduct hit frequency analyses of subsea pipelines, using historical data, and how to obtain a finite number of scenarios for the consequences analysis. An example study using probabilistic methods is used.

• Korean Journal of Veterinary Research
• /
• v.14 no.2
• /
• pp.151-157
• /
• 1974

This study was carried out to investigate on the morphology, distribution and stainability of the mast cells in the Korean Native goat. For the study, the experimental animals were anesthetized with pentobarbital sodium and opened the anterior abdomianl wall to remove immediately the specimens with a minimum of mechanical effects. The mesenteries were fixed in 10% neutral formalin, 4% basic lead acetate, absolute alcohol and ethlene glycol monoethyl ether. Following 24 hours of fixation, the toto preparation stained with 0.4% toluidine blue, 1% methylene blue, 1.5% bismark brown, saturated thionine and thionlne-methylene blue complex solution. The preparation were observed from 10 microscopic field with 450 magnification. The results were as follows: 1. The form of the mesenteric mast cell was found 2 types. One was spindle form in larger number around vessels, the other was ovoid or spherical form in connective tissue far from blood vessels. 2. The average size was $18.63{\pm}5.75{\mu}m$ in length, $10.61{\pm}3.39{\mu}m$ in width and number was $105.50{\pm}18.45$. 3. Ethylene glycol monoethyl ether was particularly useful in preserving the mast cell granules. 4. Thione-methylene blue complex solution might be recommended to stain of granules.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.2
• /
• pp.178-182
• /
• 2011

Generally in order to reduce the steel weight of stiffened plate, stiffener spaces tend to be narrow and the plate gets thin. However, it will involve more fabrication cost because it can lead to the increase of welding length and the number of structural members. In the yard, the design which is able to reduce the total fabrication cost is needed, although it requires more steel weight. The purpose of this study is to find optimum stiffener spaces to minimize the fabrication cost for the cargo tank of LPG Carriers. Global optimization methods such as ES(Evolution Strategy) and GA(Genetic Algorithm) are introduced to find a global optimum solution and the sum of steel material cost and labor cost is selected as main objective function. Convergence degree of both methods in according to the size of searching population is examined and an efficient size is investigated. In order to verify the necessity of the optimum design based on the cost, minimum weight design and minimum cost design are carried out.