• Environmental Engineering Research
• /
• v.21 no.1
• /
• pp.15-21
• /
• 2016

Magnesium potassium phosphate cement (MKPC) is an effective agent for solidification/stabilization (S/S) technology. To further explore the mechanism of the S/S by MKPC, two kinds of Cd including $Cd(NO_3)_2$ solution (L-Cd) and municipal solid waste incineration fly ash (MSWI FA) adsorbed Cd (S-Cd), were used to compare the effects of the form of heavy metal on S/S. The results showed that all the MKPC pastes had a high unconfined compressive strength (UCS) above 11 MPa. For L-Cd pastes, Cd leaching concentration increased with the increase of Cd content, and decreased with the increase of curing time. With the percentage of MSWI FA below 20%, S-Cd pastes exhibited similar Cd leaching concentrations as those of L-Cd pastes, while when the content of MSWI FA come up to 30%, the Cd leaching concentration increased significantly. To meet the standard GB5085.3-2007, the highest addition of S-Cd was 30% MSWI FA (6% Cd contained), with the Cd leaching concentration of 0.817 mg/L. The S/S of L-Cd is mainly due to chemical fixation, and the hydration compound of Cd was $NaCdPO_4$, while the S/S of S-Cd is due to physical encapsulation, which is dependent on the pore/crack size and porosity of the MKPC pastes.

• Resources Recycling
• /
• v.15 no.6 s.74
• /
• pp.33-40
• /
• 2006

Leaching behavior of copper using electro-generated chlorine was investigated in hydrochloric acid solutions. When leached copper concentration was lower than 3.6g/L, the utilization efficiency of the electro-generated chlorine was close to 100% at $10mA/cm^2,\;25^{\circ}C$, 400 rpm in 1M HCl solutions. The concentration ot the leached copper over 3.6g/L caused the electrode potential to drop quietly, leading to a change or leaching mechanism. The leaching rate oi copper began to decrease at the concentration of copper 5.2g/L. This is probably due to the formation of a layer of CuCl on Cu metal in 1M HCl solutions. The leaching rate, however, was not retarded in a solution ot high chloride concentration. The high solubility of CuCl in the solution may prevent the formation of CuCl on Cu metal.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.6
• /
• pp.217-221
• /
• 2005

The evaporation amounts of volatile Cd, Pb and Zn were characterized by measuring their total concentrations in the EAF dust-clay bodies with various mixing ratio and heat treatment temperature. TCLP test was conducted for evaluating the chemical stabilities of the heavy metal elements. Evaporation amounts and leaching concentrations of heavy metal components were strongly dependent on the mixing ratio and heat treatment temperature. The evaporation of the heavy metal components in EAF dust was effectively suppressed by increasing the clay content. The leaching concentrations of heavy metal components were decreased with increasing clay content and temperature. 20 wt% EAF dust-80 wt% clay sample shows nearly zero evaporation and leaching concentrations of heavy metal components. XRD analysis showed that peak intensities of major crystalline phases such as franklinite and quartz were decreased with increasing the heat treatment temperature which means that the stabilization mechanism of the heavy metals was related with the vitrification process of the $SiO_2$ in the clay.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.586-591
• /
• 2001

This research investigated the feasibility of the accelerated carbonation of cement waste forms with carbon dioxide in a supercritical state. Hydraulic cement has been used as a main solidification matrix for the immobilization of radioactive and/or hazardous wastes. As a result of the hydration reaction for major compounds of portland cement, portlandite (Ca(OH)$_2$) is present in the hydrated cement waste form. The chemical durability of a cement form is expected to increase by converting portlandite to the less soluble calcite (CaCO$_3$). For a faster reaction of portlandite with carbon dioxide, SCCD (supercritical carbon dioxide) rather than gaseous $CO_2$, in ambient pressure is used. The cement forms fabricated with an addition of slated lime or Na-bentonite were cured under ambient conditions for 28days and then treated with SCCD in an autoclave maintained at 34$^{\circ}C$ and 80atm. After SCCD treatment, the physicochemical properties of cement matrices were analyzed to evaluate the effectiveness of accelerated carbonation reaction. Conversion of parts of portlandite to calcite by the carbonation reaction with SCCD was verified by XRD (X-ray diffraction) analysis and the composition of portlandite and calcite was estimated using thermogravimetric (TG) data. After SCCD treatment, tile cement density slightly increased by about 1.5% regardless of the SCCD treatment time. The leaching behavior of cement, tested in accordance with an ISO leach test method at 7$0^{\circ}C$ for over 300 days, showed a proportional relationship to the square root of the leaching time, so the major leaching mechanism of cement matrix was diffusion controlled. The cumulative fraction leached (CFL) of calcium decreased by more than 50% after SCCD treatment. It might be concluded that the enhancement of the characteristics of a cement matrix by an accelerated carbonation reaction with SCCD is possible to some extent.

• Resources Recycling
• /
• v.31 no.2
• /
• pp.49-55
• /
• 2022

In the present study, the thermodynamic evaluation of the sulfate-roasting process was conducted to extract vanadium from the Korean vanadium titano-magnetite ore. The leaching efficiency of vanadium and other impurities was analyzed for varying roasting temperatures and addition of Na₂SO₄. In the case of sulfate roasting, the roasting temperature was 200 ℃ higher than that previously observed Na₂CO₃ roasting. However, the higher leaching efficiency of vanadium and lower leaching efficiency of other impurities, such as aluminum and silicon, were observed. The high selectivity for the extraction of vanadium in sulfate roasting would result from the reaction mechanism between SO₂ gas and vanadium concentrate.

• Nuclear Engineering and Technology
• /
• v.56 no.5
• /
• pp.1880-1886
• /
• 2024

To elucidate the mechanism of damage caused by hyphae and organic acids produced by Aspergillus Niger on the surface and internal structure of uranium ore, direct uranium leaching, indirect uranium leaching and semidirect uranium leaching were conducted, and the surface morphology, strength, mineral crystallinity, porosity, and permeability of the ore were analyzed. The results demonstrated that the combination of biomechanical forces exerted by hyphae and the complexation effects of organic acids led to the dissolution of SiO₂ and other substances on the surface of ore, resulting in exfoliation from the exterior to the interior, thereby promoting uranium recovery. Furthermore, the proton exchange involving H⁺ and the complexation of organic acids resulted in the dissolution of cations within the ore, causing destruction to the crystal lattice structure of minerals and increasing the porosity and permeability inside the ore. The dominant factor contributing to ore damage during recovery was organic acids.

• Membrane and Water Treatment
• /
• v.7 no.6
• /
• pp.555-571
• /
• 2016

Heavy metal contamination has attracted considerable attention during recent decades due to the potential risk brought about for human beings and the environment. Several adsorbent materials are utilized for the purification of contaminated water resources among which chitosan is considered as an appropriate alternative. Copper is a heavy metal contaminants found in several industrial wastewaters and its adsorption on porous and macroporous chitosan membranes is investigated in this study. Membranes are prepared by phase inversion and particulate leaching method and their morphology is characterized using SEM analysis. Batch adsorption experiments are performed and it is found that copper adsorption on macroporous chitosan membrane is higher than porous membrane. The iso-steric heat of adsorption was determined by analyzing the variations of temperature to investigate its effect on adsorption characteristics of macroporous chitosan membranes. Furthermore, desorption experiments were studied using NaCl and EDTA as eluants. The mechanism of copper adsorption was also investigated using XPS spectroscopy which confirms simultaneous occurrence of chelation and electrostatic adsorption mechanisms.

• Asian Journal of Turfgrass Science
• /
• v.10 no.1
• /
• pp.49-59
• /
• 1996

This report is researched on the cause and mechanism of soil erosion in comparison among Kwangnung, Mt. Kaya, Mt. Chili, and Mt. Soorak by physical and chemical analyses of their for- est soils. Clay, silt, and fine sand of Mt. Soorak are far less than those of Mt. Chili, Mt. Kaya, and Kwangnung area while coarse sand is very high level. The clay ratio of soil at Mt. Soorak is the most high level in comparison with that of other area. Denudation at Mt. Soorak, therefore, is cause of erosion by the result of transportation of soil particles. The eroding velocity increase for larger particle size and stronger cohesion between soil particles. Very fine sand, silt, and clay can be present in suspension near the bottom and the size of the particles in suspension depends upon the velocity of the current near the bottom and the roughness of the bottom. Key words: Theoretical analyses, Soil erosion and conservation, Forest soils.

• Journal of Korea Foundry Society
• /
• v.11 no.4
• /
• pp.303-313
• /
• 1991

The Purification mechanism of high purity aluminum was studied through the variation of stirring speed and coolant flow rate in the stirring method. In the stirring method the degree of purification was changed as the following factors;the variation of diffusion boundary layer thickness the variation of growth rate and the solute concentration of the residual melt. The concentration of Fe and Si was decreased as the stirring speed and the radial distance increased. In a high stirring speed of 2000rpm with unidirectional stirring mode, the uniformity of solutes was obtained. On the other hand, the purification of Si was done by the combinations of stirring method, fractional melting and acid leaching. In the case of Si purification, the centrifugal force developed in the melt acted as the significant purification factor. It was possible to obtain the purified 3N grade Si crystal after the complete elimination of residual aluminum by fractional melting and acid leaching.

• Journal of the Korean Ceramic Society
• /
• v.32 no.3
• /
• pp.385-393
• /
• 1995

Akali-resistant porous glass was prepared by phase separation in Na2O-B2O3-SiO2 system containing ZrO2 and MgO. ZrO2 was added for alkali-resistance and MgO for anti-cracking during leaching. Optimal content of ZrO2 for alkali-resistance was 7wt% and devitrification by heat treatment resulted from further addition. Pore size and pore volume were decreased and specific surface area was increased with ZrO2 addition due to depression in phase separation. Addition of 3mol% MgO to mother glass containing 7wt% ZrO2 was effective for anti-crack during leaching. In this case, with phase separation at 55$0^{\circ}C$ and 5$25^{\circ}C$ for 20 hrs. crack-free porous glasses could be prepared. The relation between pore size r and heat treatment time t at 55$0^{\circ}C$ was D=25.58＋18.16t. According to measurement of gas permeability, the mechanism of gas permeation was Knudsen flow. N2 and He permeability of porous glass which was prepared by heat treatment at 55$0^{\circ}C$ for 20 hrs. were 0.843$\times$10-7mol/$m^2$.s.Pa and 2.161$\times$10-7mol/$m^2$.s.Pa respectively.