• 융복합기술연구소 논문집
• /
• 제3권2호
• /
• pp.39-43
• /
• 2013

Titanium has been used to satisfy various applications such as bio engineering, aerospace, electronics, automobile. Recently, micro fabrication technologies of metals such as titanium have been required to satisfy many conditions in various fields. To satisfy these demands, micro electrochemical process using laser marking can be an alternative method because it is one of the precision machining and efficient process. Micro electrochemical process using laser marking needs to accomplish form of the oxidized recast layer on metal surface by laser marking. The laser beam marking conditions such as average power, pulse repetition rate and marking speed should be properly selected to form oxidized recast layer. So, the characteristics of titanium surface according to laser marking conditions was investigated through SEM(scanning electron microscope), EDS(energy dispersive spectrometer) and surface roughness analysis.

• 대한기계학회논문집A
• /
• 제20권3호
• /
• pp.891-900
• /
• 1996

The vision sensor which is based on the optical triangulation theory with the laser as an auxiliary light source can detect not only the seam position but the shape of seam. In this study, a vision sensor using the scanning laser beam was investigated. To design the vision sensor which considers the reflectivity of the sensing object and satisfies the desired resolution and measuring range, the equation of the focused laser beam which has a Gaussian irradiance profile was firstly formulated, Secondly, the image formaing sequence, and thirdly the relation between the displacement in the measuring surface and the displacement in the camera plane was formulated. Therefore, the focused beam diameter in the measuring range could be determined and the influence of the relative location between the laser and camera plane could be estimated. The measuring range and the resolution of the vision sensor which was based on the Scheimpflug's condition could also be calculated. From the results mentioned above a vision sensor was developed, and an adequate calibration technique was proposed. The image processing algorithm which and recognize the center of joint and its shape informaitons was investigated. Using the developed vision sensor and image processing algorithm, the shape informations was investigated. Using the developed vision sensor and image processing algorithm, the shape informations of the vee-, butt- and lap joint were extracted.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.20-20
• /
• 2010

The effect of excimer laser annealing on the structural and dielectric behaviors of $PbZr_{0.52}Ti_{0.48}O_3$ (PZT) thin films has been investigated. The amorphous PZT thin films were prepared on Pt/Ti/$SiO_2$/Si substrates by a sol-gel method. The PZT precursor was prepared from lead acetate, zirconium acetylacetonate, and titanium isopropoxide. The starting materials were dissolved in n-propanol and 1,3-propanediol. After, the amorphous PZT thin films were laser-annealed (using KrF excimer laser) as a function of the laser energy density and the number of laser pulse. Structural properties of PZT thin films are characterized by using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The dielectric characterization was done on a RT66A test system and a Agilent 4294A impedance analyzer. The PZT thin films show that excimer laser irradiation drastically improved the crystallization and dielectric properties of the PZT thin films, depending on the energy density and the pulse number.

• Journal of Korean Vacuum Science & Technology
• /
• 제6권2호
• /
• pp.101-104
• /
• 2002

Er doped SiOx films have been synthesized by ion beam assisted deposition (IBAD). The morphology and microstructure of films and their annealing behaviors have been examined by using scanning electron microscopy and x-ray diffraction. The composition and properties of films have been systematically investigated.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1501-1506
• /
• 2005

This paper presents the design of a multiple beam optical tweezers instrument used for manipulating micro/nano-sized components. The basic equations used in designing the optical tweezers are derived and the stable and time-sharing multiple beam optical tweezers are constructed with scanning mirrors. The laser beam passes through a series of optical components such as lenses, mirrors, and scanning mirrors, and overfills the entrance aperture of microscope objective, which gives a stable trap. By rotating the laser beam with the scanning mirror, the focal positions are translated in the specimen plane and multiple micro/nano-sized objects can be moved. The constructed optical tweezers is used to manipulate cells and liposomes simultaneously and to trap multiple nano-wires. The experiments prove that the developed optical tweezers can be a very versatile manipulation tool for studying gene therapy and nano device fabrication.

• 비파괴검사학회지
• /
• 제35권6호
• /
• pp.389-397
• /
• 2015

Recently, wave propagation imaging based on laser scanning-generated elastic waves has been intensively used for nondestructive inspection. However, the proficiency of the conventional software based system reduces when the scan area is large since the processing time increases significantly due to unavoidable processor multitasking, where computing resources are shared with multiple processes. Hence, the field programmable gate array (FPGA) was introduced for a wave propagation imaging method in order to obtain extreme processing time reduction. An FPGA board was used for the design, implementing post-processing ultrasonic wave propagation imaging (UWPI). The results were compared with the conventional system and considerable improvement was observed, with at least 78% (scanning of $100{\times}100mm^2$ with 0.5 mm interval) to 87.5% (scanning of $200{\times}200mm^2$ with 0.5 mm interval) less processing time, strengthening the claim for the research. This new concept to implement FPGA technology into the UPI system will act as a break-through technology for full-scale automatic inspection.

• Applied Microscopy
• /
• 제50권
• /
• pp.24.1-24.11
• /
• 2020

The development of the femtosecond laser (fs laser) with its ability to provide extremely rapid athermal ablation of materials has initiated a renaissance in materials science. Sample milling rates for the fs laser are orders of magnitude greater than that of traditional focused ion beam (FIB) sources currently used. In combination with minimal surface post-processing requirements, this technology is proving to be a game changer for materials research. The development of a femtosecond laser attached to a focused ion beam scanning electron microscope (LaserFIB) enables numerous new capabilities, including access to deeply buried structures as well as the production of extremely large trenches, cross sections, pillars and TEM H-bars, all while preserving microstructure and avoiding or reducing FIB polishing. Several high impact applications are now possible due to this technology in the fields of crystallography, electronics, mechanical engineering, battery research and materials sample preparation. This review article summarizes the current opportunities for this new technology focusing on the materials science megatrends of engineering materials, energy materials and electronics.

• Architectural research
• /
• 제21권4호
• /
• pp.111-116
• /
• 2019

The premise of this research is the recent advancement of Building Information Modeling(BIM) Technology and Laser Scanning Technology(3D Scanning). The purpose of the paper is to amplify the potential offered by the combination of BIM and Point Cloud Data (PCD) for structural analysis. Today, enormous amounts of construction site data can be potentially categorized and quantified through BIM software. One of the extraordinary strengths of BIM software comes from its collaborative feature, which can combine different sources of data and knowledge. There are vastly different ways to obtain multiple construction site data, and 3D scanning is one of the effective ways to collect close-to-reality construction site data. The objective of this paper is to emphasize the prospects of pre-scanning and post-scanning automation algorithms. The research aims to stimulate the recent development of 3D scanning and BIM technology to develop Scan-to-BIM. The paper will review the current issues of Scan-to-BIM tasks to achieve As-Built BIM and suggest how it can be improved. This paper will propose a method of coordinating and utilizing PCD for construction and structural analysis during construction.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.142-145
• /
• 2004

More complex geometric shapes, including freeform surfaces, are adopted for the design of products to emphasize styling or aesthetics. Modeling of these products is extremely difficult, and often impossible. Reverse engineering is an emerging technology that can resolve this problem by generating CAD models from the physical mockups or prototype models. The laser scanner if often used to acquire the surface information of the part, but is limited in its measuring direction, which if fixed only along the z-axis. A Designed fixture of new shape to supplement these problems in this paper. The new fixture using several joints and an tooling ball holder is designed considering the convenience of the part set-up and the accuracy of the registration. The location of the tooling balls can be arranged to avoid the occlusion of the part and to minimize the registration error. The new fixture is apply to an object part having freeform surfaces to verify the effectiveness of the proposed design.

• 소성∙가공
• /
• 제18권3호
• /
• pp.262-267
• /
• 2009

Selective laser sintering is a kind of rapid prototyping process whereby a three-dimensional part is built layer wise by laser scanning the powder. This process is highly influenced by powder and laser parameters such as laser power, scan rate, fill spacing and layer thickness. Therefore a study on fabricating Fe-Ni-Cr powder by selective laser sintering has been performed. In this study, fabrication was performed by experimental facilities consisting of a 200W fiber laser which can be focused to 0.08mm and atmospheric chamber which can control atmospheric pressure with argon. With power increase or energy density decrease, line width was decreased and line surface quality was improved with energy density increase. Surface quality of quadrangle structure was improved with fill spacing optimization.