• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2007.04a
• /
• pp.379-382
• /
• 2007

Laser scanning technology with high positional accuracy and high density automation will be widely applied in vast range of fields including geomatics. Especially, the development of laser scanning technology enabling long range information extraction is increasing its full use in civil engineering. The purpose of this study is to extract accurate highway geometric information taking the advantages of scanning technology. Fulfilling this goal, the information of target highway's three-dimensional data was obtained through terrestrial laser scanning technology. In accordance with the result from target highway's geometric information extraction using the information above, laser scanning technology showed faster speed and better accuracy on highway geometric information extraction with reduced cost compared to traditional methods.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.3
• /
• pp.171-179
• /
• 2004

Micro-stereolithography technology has made it possible to fabricate a freeform 3D microslructure. This technology is based on conventional stereolithography, in which a UV laser beam irradiates the open surface of a UV-curable liquid photopolymer, causing it to solidify. In micro-stereolithography, a laser beam of a few $\mu m$ diameter is used to solidify a very small area of the photopolymer. This is one of the key technological elements, and can be achieved by using a focusing lens. Thus, the solidification phenomena of the liquid photopolymer must be carefully investigated. In this study, the photopolymer solidification phenomena in response to variations in the scanning pitch of a focused laser beam was investigated experimentally. The effect of layer thickness on the solidification width and depth was also examined. These studies were conducted under the conditions of relatively lower laser power and relatively higher scanning speed. Moreover, the photopolymer solidification phenomena for the relatively higher laser power and lower scanning speed was investigated, too. In this case, comparing to the case of lower laser power and higher scanning speed, the photopolymer absorbed large amount of irradiation energy of the laser beam. These results were compared with those obtained from a photopolymer solidification model. From these results, a new laser-scanning scheme was proposed according to the shape of the 3D model. Samples by each method were fabricated successfully.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.943-946
• /
• 2004

We report the laser scanning display as an emerging technology. We show demonstration system of laser TV, Video image is made by using a high speed MEMS scanning mirror and a direct-modulated red diode laser. We designed and fabricated MEMS scanning mirror. The first demonstration system showed a NTSC-resolution video image with the image size of 5 inches. The successful development of compact laser TV will open a new area of home application of the laser light.

• Korean Journal of Computational Design and Engineering
• /
• v.16 no.2
• /
• pp.126-136
• /
• 2011

The existing approaches to freeform building construction cause many problems. However, recent BIM technique development based on parametric modeling method and improvement of freeform materials manufacturing technology using IT technology encouraged many advanced countries to try experimental projects. Thus, laser scanning technique is in the limelight as a new alternative in the field of freeform building construction and inspection. This study selected a domestic small freeform building and practiced laser scanning and as-planned modeling by using Reverse Engineering. Then each deviation was comparatively analyzed through figures which extracted data by numerically analyzing the newly modeled as-built and Excel spread sheet. Through the process, limits and follow-up research subjects are discussed as well.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.26 no.1
• /
• pp.108-113
• /
• 2017

In this paper, we proposed a three-dimensional(3D) scanning system based on laser vision technique for 3D model reconstruction. The proposed scanning system consists of line laser, camera, and turntable. We implemented the 3D scanning system using low quality elements. Although these are low quality elements, we reduced the 3D data reconstruction errors greatly using two methods. First, we developed a maximum brightness detection algorithm. This algorithm extracts the maximum brightness of the line laser to obtain the shape of the object. Second, we designed a new laser control device. This device helps to adjust the relative position of the turntable and line laser. These two methods greatly reduce the measuring noise. As a result, point cloud data can be obtained without complicated calculations.

• Smart Structures and Systems
• /
• v.22 no.2
• /
• pp.223-230
• /
• 2018

This study examines a non-contact laser scanning-based ultrasound system, called an angular scan pulse-echo ultrasonic propagation imager (A-PE-UPI), that uses coincided laser beams for ultrasonic sensing and generation. A laser Doppler vibrometer is used for sensing, while a diode pumped solid state (DPSS) Q-switched laser is used for generation of thermoelastic waves. A high-speed raster scanning of up to 10-kHz is achieved using a galvano-motorized mirror scanner that allows for coincided sensing and for the generation beam to perform two-dimensional scanning without causing any harm to the surface under inspection. This process allows for the visualization of longitudinal wave propagation through-the-thickness. A pulse-echo ultrasonic wave propagation imaging algorithm (PE-UWPI) is used for on-the-fly damage visualization of the structure. The presented system is very effective for high-speed, localized, non-contact, and non-destructive inspection of aerospace structures. The system is tested on an aluminum honeycomb sandwich with disbonds and a carbon fiber-reinforced plastic (CFRP) honeycomb sandwich with a layer overlap. Inspection is performed at a 10-kHz scanning speed that takes 16 seconds to scan a $100{\times}100mm^2$ area with a scan interval of 0.25 mm. Finally, a comparison is presented between angular-scanning and a linear-scanning-based pulse-echo UPI system. The results show that the proposed system can successfully visualize defects in the inspected specimens.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.3
• /
• pp.72-76
• /
• 2019

A Q-switched diode-pumped neodymium-doped yttrium vanadate (YVO₄, λ =1064nm) laser was used for the direct patterning of indium tin oxide (ITO) films on glass substrate. During the laser direct patterning, the laser beam was incident on the two different directions of glass substrate and the laser ablated patterns were compared and analyzed. At a low scanning speed of laser beam, the larger laser etched lines were obtained by laser beam incident in reverse side of glass substrate. On the contrary, at a higher scanning speed, the larger etched pattern sizes were found in case of the beam incidence from front side of glass substrate. Furthermore, it was impossible to find no ablated patterns in some laser beam conditions for the laser beam from reverse side at a much higher scanning speed and repetition rate of laser beam. The laser beam is expected to be transferred and scattered through the glass substrate and the laser beam energy is thought to be also dispersed and much more influenced by the overlapping of each laser beam spot.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.12
• /
• pp.1121-1126
• /
• 2014

To compensate location error of ultrasonic horn, the laser scanning system based on the galvanometer scanner is developed. It consists of the 3-Axis linear stage and the 2-Axis galvanometer scanner. To measure surface shape of three-dimensional free form surface, the dynamic focusing unit is adopted, which can maintain consistent focal plane. With combining the linear stage and the galvanometer scanner, the scanning area is enlarged. The scanning CAD system is developed by stage motion teaching and NURBS method. The laser scanning system is tested by marking experiment with the semi-cylindrical sample. Scanning accuracy is investigated by measured laser marked line width with various scanning speed.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.05a
• /
• pp.227-228
• /
• 2016

Terrestrial laser scanning (TLS) technology is being applied to various fields such as the soil volume calculation and the displacement measurement of terrain, tunnels and dams. This study develops a 3D terrain processing platform for automated earth work using a terrestrial laser scanning data as the software prototype. The developed software provides cells with geo-technical information for planning work to an integrated system.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.13 no.4
• /
• pp.49-56
• /
• 2017

It is the approach of embedded system design that finds 3D scanning technology to analyze a real object or environment to collect data on its shape and appearance. 3D laser scanning developed during the last half of 20th century in an attempt to accurately recreate the surfaces of various objects. 1960s, early scanners used lights, cameras, and projectors to carry out the scanning in the lacks of performance which encountered many difficulties with shiny, mirroring, or transparent objects. The 3D scanning technology has leveled-up with helpful of embedded software platform research and design. In this paper, First we designed the hardware of laser/camera setup and turntable moving part which is the base of object. Second, we introduced the process of scanning 3D data with software and analyzed the resulting scanned image on the web server. Last, we made the 3D scanning embedded device with 3D printing model and experimented the 3D scanning performance with Raspberry Pi.