• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.3
• /
• pp.53-56
• /
• 2017

Laser cladding is a technique for forming beads by melt-sintering with a laser while directly feeding metal powder onto the base material through nozzles. This technique, which is applied in laser surface treatment technology, is useful for repairing broken or worn parts by allowing selective formation of the surface layer of the base metal material. In this paper, laser cladding process was performed on STS316L powder using high power continuous wave laser with IR wavelength and the cladding characteristics according to process conditions were experimentally analyzed.

• Laser Solutions
• /
• v.2 no.2
• /
• pp.8-17
• /
• 1999

This study includes a basic feature of laser surface alloying for enhancing the surface properties of materials. Effects of laser processing parameters such as beam power, beam size, scanning speed on the shape and composition of alloyed layer was simulated in case of moving beam conditions (2-dimensional numerical methods). Simulated results were compared with experiments, in which the plasma coating of 80% Ni ＋ 20% Cr deposited on the SS41 substrate was remelted with CO2 laser with Gaussian energy distribution. Simulation and experiments revealed that the shape (dimension)and composition of laser alloyed layer were strongly dependent upon the process parameters, especially interaction time (travel speed) as compared to beam diameter, beam power and absorptivity. The shape and composition of alloyed layervaried more or less exponentially with parameters.

• Laser Solutions
• /
• v.10 no.2
• /
• pp.17-24
• /
• 2007

We have studied a laser direct writing lithography(LDWL). This is more important to apply to micro patterning using UV laser. We demonstrate the possibility of LDWL and construct the fabrication system. We use Galvano scanner to process quickly micro patterns from computer data. And laser beam is focused with $F-{\theta}$ lens. AZ5214 and SU-8 photoresist are chosen as experimental materials and a kind of well-known positive and negative photoresist respectively. Laser ablation mechanism depends on the optical properties of polymer. In this paper, therefore we investigate the phenomenon of laser ablation according to the laser fluence variation and measure the shape profile of micro patterned holes. From these experimental results, we show that LDWL is very useful to process various micro patterns directly.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.4-4
• /
• 2009

Polycarbonate (PC) and Acrylonitrile Butadiene Styrene (ABS) was welded through a combination of a diode laser and CNC. Laser beam passed the transparent PC and was absorbed in an opaque ABS. Polymers were melted and welded by absorbed and conducted heat. Experiments were carried out by varying working distance from 44mm to 50mm for the focus spot diameter control, laser input power from 10W to 25W, and scanning speed from 100 to 400mm/min. The weld bead size and the specimen cross-section were analyzed, and tensile results were presented through the joint force measurement. With focus distance at 48mm, laser power with 20W, and welding speed at 300mm/min, experimental results showed the best welding quality which bead size was 3.75mm and the shear strength was $22.8N/mm^2$. Considering tensile strength of ABS is $43N/mm^2$, shear strength was sufficient to hold two materials. A single process was possible in CNC machining processes, surface processing, hole machining and welding. As a result, the process cycle time was reduced to 25%. Compared to a typical process, specimens were fabricated in a single process, with high precision. By combining two operations processes developed process gained 50% more efficiency.

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2000.11a
• /
• pp.23-26
• /
• 2000

This paper introduces a cleaning process for removing submicron-sized particles from NiP hard disk substrates by the liquid-assisted laser cleaning technique. Measurements of cleaning performance and time-resolved optical diagnostics are performed to analyze the physical mechanism of contaminant removal. The results reveal that nanosecond laser pulses are effective for removing the contaminants regardless of the wavelength and that a thermal mechanism involving explosive vaporization of liquid dominates the cleaning process.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.6
• /
• pp.2353-2358
• /
• 2017

A femtosecond laser pre-annealing process based on indium zinc oxide (IZO) thin-film transistors (TFTs) is fabricated. We demonstrate a stable pre-annealing process to analyze surface structure change of thin films, and we maintain electrical stability and improve electrical performance. Furthermore, dynamic electrical characteristics of the IZO TFTs were investigated. Femtosecond laser pre-annealing process-based IZO TFTs exhibit a field-effect mobility of $3.75cm^2/Vs$, an $I_{on}/I_{off}$ ratio of $1.77{\times}10^5$, a threshold voltage of 1.13 V, and a subthreshold swing of 1.21 V/dec. And the IZO-based inverter shows a fast switching behavior response. From this study, IZO TFTs from using the femtosecond laser annealing technique were found to strongly affect the electrical performance and charge transport dynamics in electronic devices.

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.3
• /
• pp.56-59
• /
• 2006

UV laser micromachining is generally used to create microstructures for micro-products through a sequence of lithography-based photo-patterning steps. However, the micromachining process is not suitable for rapid realization of complex 3D micro-products because it depends on worker experience. In addition, the cost and time required to make many masks are excessive. In this paper, a more effective and rapid micro-manufacturing process, which was developed based on laser micromachining, is proposed for fabricating micro-products directly using UV laser ablation and phase-change filling. The filling process is useful for holding the micro-products during the ablation step. The proposed rapid micro-manufacturing process was demonstrated experimentally by fabricating 3D micro-products from functional UV-sensitive polymers using 3D CAD data.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.26-29
• /
• 2003

UV laser micromachining are generally used to create microstructures for micro product through a sequence of lithography-based photopatterning steps. However, the micromachining process is not suitable for the rapid realization of complex microscale 3D product because it depends on worker experiences, excessive cost and time to make many masks. In this paper, the more effective micro rapid manufacturing process, which is developed upon the base of laser micromachining. is proposed to fabricate micro products directly using UV laser ablation and phase change filling. The filling process is useful to hold the micro product during the next ablation step. The proposed micro rapid manufacturing process is also proven experimentally that enables to fabricate the 3D microscale products of UV sensitive polymer from 3D CAD data to functional micro parts.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.11 s.176
• /
• pp.196-201
• /
• 2005

UV laser micromachining are generally used to create microstructures for micro product through a sequence of lithography-based photopatterning steps. However, the micromachining process is not suitable for the rapid realization of complex 3D micro product because it depends on worker experiences, excessive cost and time to make many masks. In this paper, the more effective micro rapid manufacturing process, which is developed upon the base of laser micromachining, is proposed to fabricate micro products directly using UV laser ablation and phase change filling. The filling process is useful to hold the micro product during the next ablation step. The proposed micro rapid manufacturing process is also proven experimentally that enables to fabricate the 3D micro products of UV sensitive polymer from 3D CAD data to functional micro parts.

• Transactions of Materials Processing
• /
• v.7 no.6
• /
• pp.519-529
• /
• 1998

In automotive industries the stamping of laser-welded blank gives many merits which bring about dimensional accuracy, strong body assembly and high productivity. However the welding of blanks with different thickness or/and different strength materials introduces many challenging formability problems for process development and tool design. in this paper the deformation characteristics for deep drawing process of laser-welded blank with different thickness sheets are investigated by experiment as well as by FEM simulation. The blank holding force ratio to avoid the movement of weld line was suggested and compared with the experimental result for cylindrical and rectangular cup drawing process. The optimal location of weld line in laser-welded blank with different thickness sheets is calculated to compensate for the movement of weld line on deep drawing process. In addition the effect of location of weld line on formability is clarified using FEM simulation.