• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.187-192
• /
• 2002

Applicability of laser micro welding process to the fabrication of medical devices was investigated. Austenitic stainless steel wire (SUS304) was spot melted and crosswise welded, which is one of the most possible welding process for the fabrication of medical devices, by using a Nd-YAG laser. Effects of welding parameters on the microstructure, tensile strength and corrosion resistance were discussed. In the spot melting, melted metal width decreased with decreasing the input energy and pulse duration. Controlling the laser wave to reduce laser noise which occurred in the early stage of laser irradiation made reasonable welding condition wider in the welding condition of small pulse duration such as 2ms. The microstructure of the melted metal was a cellular dendrite structure and the cell size of the weld metal was about 0.5~3.5 ${\mu}{\textrm}{m}$. Tensile strength increased with the decrease of the melted metal width and reached to a maximum about 660MPa, which is comparable with that for the tempered base metal. Even by immersion test at 318K for 3600ks in quasi biological environment (0.9% NaCl), microstructure of the melted metal and tensile strength hardly changed from those for as melted material. In the crosswise welding, joints morphologies were classified into 3 types by the melting state of lower wire. Fracture load increased with input energy and melted area of lower wire, and reached to a maximum about 80N. However, when input energy was further increased and lower wire was fully melted, fracture load decreased due to the burn out of weld metal.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.252-255
• /
• 2003

The pulsed laser deposition process modeling is investigated using neural networks based on radial basis function networks and multi-layer perceptron. Two input factors are examined with respect to the PL intensity. In order to minimize the joint confidence region of fabrication process with varying the conditions, D-optimal experimental design technique is performed and photoluminescence intensity is characterized by neural networks. The statistical results were then used to verify the fitness of the nonlinear process model. Based on the results, this modeling methodology can be optimized process conditions for pulsed laser deposition process.

• Journal of Welding and Joining
• /
• v.26 no.3
• /
• pp.30-36
• /
• 2008

A flip-chip bonding system using IR laser with a wavelength of 1064 nm was developed and associated process parameters were analyzed using Taguchi methods. An infrared laser beam is designed to transmit through a silicon chip and used for transferring laser energy directly to micro-bumps. This process has several advantages: minimized heat affect zone, fast bonding and good reliability in the microchip bonding interface. Approximately 50 % of the irradiated energy can be directly used for bonding the solder bumps with a few seconds of bonding time. A flip-chip with 120 solder bumps was used for this experiment and the composition of the solder bump was Sn3.0Ag0.5Cu. The main processing parameters for IR laser flip-chip bonding were laser power, scanning speed, a spot size and UBM thickness. Taguchi methods were applied for optimizing these four main processing parameters. The optimized bump shape and its shear force were modeled and the experimental results were compared with them. The analysis results indicate that the bump shape and its shear force are dominantly influenced by laser power and scanning speed over a laser spot size. In addition, various effects of processing parameters for IR laser flip-chip bonding are presented and discussed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.5 no.1
• /
• pp.51-58
• /
• 2006

The objective of this research work is to investigate into heat transfer characteristics of the laser cutting of CSP 1N sheet using high power CW Nd:YAG laser. In order to investigate the heat transfer characteristics, three dimensional quasi stationary and steady-state heat transfer analysis has been carried out. The laser heat source is assumed as a volumetric heat source with a gaussian heat distribution in a plane. Through the comparison of the results of analyses with those of experiments, the proper finite element model has been obtained. In addition, characteristics of the three-dimensional heat transfer and temperature distribution have been estimated by the finite element model. Finally, the minimum temperature at the center for cutting of the material has been estimated.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.105.1-105.1
• /
• 2011

To enhance the performance of photovoltaic a-Si:H solar cells with a hybrid-type light absorbing structure of single crystal silicon nanoparticles (Si NPs) in a-Si:H matrix, single crystal Si NPs were produced by laser pyrolysis. The Si NPs were synthesized by $SiH_4$ gas decomposition using a $CO_2$ laser. The properties of Si NPs were controlled by process parameters such as $CO_2$ laser power, reactive gas pressure, and $H_2/SiH_4$ gas flows. The crystalline properties and sizes of Si NPs were analyzed by High Resolution Transmission Electron Microscopy (HRTEM). The sizes of Si NPs were controllable in the range of 5-15 nm in diameter and the effects of process parameters of laser pyrolysis were systematically investigated.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1159-1165
• /
• 2003

The Nd:YAG laser process is known to have high speed and deep penetration capability to become one of the most advanced welding technologies. In spite of its good mechanical characteristics, SM45C carbon steel has a high carbon contents and suffers a limitation in the industrial application due to the poor welding properties. The major process parameters studied in the present laser welding experiment were position of focus, travel speed and laser power.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.748-751
• /
• 2000

Microlens made by laser radiation method have advantages in the easiness of their fabrication. The process is based on the projection of a chromium-on-quartz reticle on to the Polymer using a pulsed 248nm KrF excimer laser. Fabrication process is a fluence-dependent rate and density. The lens shape is defined by a rotationally symmetric sluence distribution with smooth radial variation in the image plane of the reticle. A typical lens of 50㎛ diameter was fabricated by irradiating 2000 laser pulses within 40 seconds. The experimental results show microlens fabrication by UV laser is possible and well worth studying further.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.616-619
• /
• 2003

Photochemical and photothermal effects have correlation with each other and depend on laser wavelength. Multi-scanning laser ablation process of polymer with DPSS(Diode Pumped Solid State) 3rd harmonic Nd:YVO$_4$ laser with wavelength of 355nm is applied to fabricate three-dimensional micro shape. The DPSSL photomachining system can rapidly and cheaply fabricate 2D pattern or 3D shape with high efficiency because we only use CAD/CAM software and precision stages instead of complex projection mask. Photomachinability of polymer is highly influenced by laser wavelength and its own chemical structure. So the optical characteristics of polymers for 355nm laser source is investigated by experimentally and theoretically.

• Laser Solutions
• /
• v.11 no.1
• /
• pp.7-11
• /
• 2008

Decapsulation technology is useful to inspect EMC of package device and the etching technology enable to check inside of device by removing plastic molding. Chemical etching method is used widely to fabricate a lot of semiconductor. But the method has some disadvantage due to wet process. Proposed method in this paper shows the application possibility such as fast processing time, processing accuracy and dry process. These result was obtained by directly removing of packed EMC using UV laser.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.7 s.172
• /
• pp.38-46
• /
• 2005

In laser machining such as drilling with $CO_2$ or Nd:YAG laser, and etching or ablation with Excimer laser, one of the most important parameters affecting the machining is known to be beam characteristics. In this paper a numerical study is performed to investigate the effects of beam parameters, especially in the process of excimer laser ablation of polymers. Results of different beam conditions reveal that if the ablated depth is small compared to beam size the simple photochemical etching model is suitable to predict the etched shape, and that the importance of precise alignment becomes large as beam quality factor becomes larger.