• Laser Solutions
• /
• v.12 no.4
• /
• pp.12-16
• /
• 2009

The engineering ceramic is one of the materials advantageous in various conditions with high strength, endurance at high temperature, abrasion resistance and corrosion resistance, etc. However, due to high strength and high brittleness, ceramic incurs high costs and long time on finishing process required after sintering. So a process for obtaining wanted measurements of them has been studied using the high temperature which makes ceramics softened and heat affected recently. This study makes an estimate of laser-assisted machining (LAM) if an economically practical process for manufacturing precision silicon nitride ceramic parts using laser beam. In this study, mechanical properties of silicon nitride at high temperature were observed. And during the LAM, it was observed that cutting force and tool wear were reduced and oxidation of machined surface was increased according to a increase of laser power.

• Journal of Welding and Joining
• /
• v.32 no.2
• /
• pp.63-69
• /
• 2014

Dual laser heat sources were used for polymer based material joining. An infrared camera and thermocouple DAQ system were used to correlate the temperature distribution to computer simulation. A 50 degree tilted pre-heating laser source was acting as a heating source to promote the temperature to minimize thermal shock by the following a welding heat source. Based on the experimental result, the skin depth was empirically estimated for computer simulation. The offsets of 3mm, 5mm and 10mm split by weld and preheat were effectively used to control the temperature distribution for the optimal laser joining process. The closer offset resulted in an excessive melting or burning caused by sudden temperature rising. The laser power was split by 50%, 75% and 100% of the weld power, and the best results were found at 50% of preheating. To accurately simulate the physical laser beam absorption and joining optical properties were experimentally measured for the computer FEM simulation. The simulation results showed close correlation between theoretical and experimental results. The developed dual laser process is expected to increase productivity and minimize the cost for the final products.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.4 s.181
• /
• pp.183-190
• /
• 2006

Digital 3D Real Object Duplication System (RODS) consists of 3D Scanner and Solid Freeform Fabrication System (SFFS). It is a device to make three-dimensional objects directly from the drawing or the scanning data. In this research, we developed an office type SFFS based on Three Dimensional Printing Process and an industrial SFFS using Dual Laser. An office type SFFS applied sliding mode control with sliding perturbation observer (SMCSPO) algorithm for control of this system. And we measured process variables about droplet diameter measurement and powder bed formation etc. through experiments. In case of industrial type SFFS, in order to develop more elaborate and speedy system for large objects than existing SLS process, this study applies a new Selective Dual-Laser Sintering (SDLS) process and 3-axis Dynamic Focusing Scanner for scanning large area instead of the existing f lens. In this process, the temperature has a great influence on sintering of the polymer. Also the laser parameters are considered like that laser beam power, scan speed, and scan spacing. Now, this study is in progress to evaluate the effect of experimental parameters on the sintering process.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.2
• /
• pp.66-75
• /
• 1993

This paper proposes a monitoring method for nondestructive and in-process measurement of the case depth in LASER surface heat treatment process. The method is essentially an eddy-current method, and measures sensing coil's electrical impedance which varies with the changes of the material microstructure due to hardening. To investigate te validity of the proposed method a series of experiments were performed for various hardning depths. The results show that the relationship between the eddy- current sensor output and the changes in case depth is almost linear. This indicates that the eddy-current measuring method can be used as one of the possible monitoring method for mesauring the hardened depth in LASER heat treatment processes.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.1
• /
• pp.79-84
• /
• 2003

A light guide panel is an element of the LCD backlight module that is often used for the display of compact electronic devices. In this study, a laser marking system is proposed to fabricate light guide panel, which can replace other manufacturing methods such as silk printing, stamping, or v-cutting methods. The objective of this research is to evaluate the process parameters of the laser marking system. Light guide patterns were marked with a 50W $CO_2$ laser (CW) to understand the effects of average power and scanning speed on the geometry and quality of groove pattern. The width of the fabricated grooves increases with increasing laser power and decreasing scan speed. In order to analyze surface characteristics and optical properties (luminance, uniformity), SEM photography and BM7 (luminance measuring system) were used. As a result, the optimal conditions of the process parameters were determined.

• Journal of Welding and Joining
• /
• v.13 no.4
• /
• pp.113-121
• /
• 1995

This study deals with the quality and the optimum range of laser cutting process. Cold rolled steel sheets for automobile application were cut by a high power CO$_{2}$ laser system with beam quality of TEM$_{\infty}$ mode. Both process parameters such as travel speed and assist gas pressure, and quality factors were considered to optimize the laser cutting. It was revealed that the thinner the sheet thickness, the less effect of oxidation energy for contributing the cutting process. High speed photographs demonstrated that molten spot on the cut surface moved in a random and vigorous manner according to its viscosity and the flowing direction of assist gas, which resulted in so called striation. Laser cutting produced a very smooth surface of average roughness(Ra) about less than 1.5.mu.m at the optimum range. It was also shown that the characteristics of dross formation was influenced by the flowing durection of assist gas and the fluidity of molten metal drop..

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.1
• /
• pp.33-38
• /
• 2012

An experimental study was carried out to observe the characteristics of impingement of assist gas from a rectangular supersonic nozzle on kerf surface in laser machining. A micro-scale supersonic (Mach number 2.0) rectangular nozzle system was designed and fabricated for the purposes, and hot tests of the performance of the nozzle system was proceeded in the ITI corporation laboratory. For various related parameters such as laser powers, nozzle pressures and cutting speeds, the quality of the frontal view of cut edge surfaces was observed by a microscope. In the study, it was shown that the application of the present micro-rectangular supersonic nozzle in an off-axis configuration made it possible to cut a mild steel, by combinations of relatively low laser - powers, large standoff distances, and assist gas with no oxygen, which was not achieved by conventional laser cutting processes.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.612-615
• /
• 2003

Maskless laser patterning process is developed using 3rd harmonic Diode Pumped Solid State Laser with near visible wavelength of 355 nm. Photo-sensitive curable polymer is irradiated by UV laser and developed using polymer solvent to obtain quasi-3D patterns. We performed basic experiments for the various process conditions such as laser power, writing speed, laser focus, and polymer optical property to gain the optimal conditions. Experimentally, the patterns of trapezoidal shape were manufactured into dimension of 8${\mu}{\textrm}{m}$ width and 5.4${\mu}{\textrm}{m}$ height. This process could be applied to fabricate a single mode waveguide without expensive mask projection method.

• Laser Solutions
• /
• v.10 no.1
• /
• pp.19-27
• /
• 2007

Previous studies demonstrated that laser ablation under transparent liquid can result in ablation enhancement and particle removal from the surface. Although the ablation enhancement by liquid is already known for semiconductor and metal, the phenomena of polymer ablation have not been studied. In this work, tile liquid-assisted excimer laser ablation process is examined for polymer materials, such as polyethylene terephthalate (PET), polymethyl methacrylate (PMMA) with emphasis on ablation enhancement and surface topography. In the case of PET and PMMA, the effect of liquid is analyzed both for thin water film and bulk water. The results show that application of liquid increases the ablation rate of PMMA while that of PET remains unchanged even in the liquid-assisted process. However, the surface roughness is generally deteriorated in the liquid-assisted process. The surface topography is found to be strongly dependent on the method of liquid application, i.e., thin film or bulk liquid.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.22-22
• /
• 2009

Laser forming is a promising technology in manufacturing, such as in the shipbuilding, automobile, microelectronics, aerospace and other manufacturing industries. This process forms the sheet metal by utilization of laser-induced thermal stresses. Laser forming process has been studied extensively for rectangular shape geometry. This basic study presents the change in deformation behavior of sheet metal during transition from linear to curved geometries and irradiations as well. A series of experiments have been conducted on a wide range of specimen geometries such as quarter-circular and half circular plate. The reasons for this behavior have been analyzed. Results are compared and analyzed by simulations using ABAQUS. Influence of developed stresses on the bending has been investigated. This study provides the more understanding of forming mechanism influenced by geometry effect.