• Wind and Structures
• /
• v.13 no.3
• /
• pp.257-273
• /
• 2010

The aerodynamic and aero-elastic model tests of the China''s highest cooling tower has been carried out in the TJ-3 Boundary Layer Wind Tunnel of Tongji University. By adopting a scanivalve system, the external wind pressure is firstly measured on $12{\times}36$ taps for a single tower, two and four grouped towers under the condition of both smooth flow and the boundary layer due to surrounding geographic and building topography. The measurements of internal wind pressure distribution of $6{\times}36$ taps are taken for a single tower under the various ventilation ratios ranging from 0% to 100% of stuffing layers located at the bottom of the tower. In the last stage, the wind tunnel tests with an aero-elastic model are carefully conducted to determine wind-induced displacements at six levels (each with eight points) with laser displacement sensors. According to the measurement results of wind pressure or vibration response, the extreme aerodynamic loading values of the single or grouped towers are accordingly analyzed based on probability correlation technique.

• Korean Journal of Optics and Photonics
• /
• v.18 no.3
• /
• pp.196-201
• /
• 2007

A theoretical study of Brillouin optical time domain analysis (BOTDA) using two pulse lasers is performed. Even though a point detection is made for a pump pulse period, the dynamic range of BOTDA using two pulse lasers is approximately 5 dB more than that of a pulse and a CW laser when the fiber length is 140 km and the Stokes power is 1 mW.

• International Journal of Fluid Machinery and Systems
• /
• v.3 no.4
• /
• pp.360-368
• /
• 2010

This paper describes the flow field and the blade pressure distribution of a horizontal axis wind turbine in various yawed flow conditions. These measurements were carried out with 2.4m-diameter rotor with pressure sensors and a 2-dimensional laser Doppler velocimeter for each azimuth angle in a wind tunnel. The results show that aerodynamic forces of the blade based on the pressure measurements change according to the local angle of attack during rotation. Therefore the wake of the yawed rotor becomes asymmetric for the rotor axis. Furthermore, the relations between aerodynamic forces and azimuth angles change according to tip speed ratio. By the experimental analysis, the flow field and the aerodynamic forces for each azimuth angle in yawed flow condition were clarified.

• Journal of the Korean Ceramic Society
• /
• v.54 no.3
• /
• pp.167-183
• /
• 2017

Zinc oxide (ZnO) is one of the most versatile semiconductors, and one-dimensional (1D) ZnO nanostructures have attracted significant interest for use in ultraviolet (UV) lasers, photochemical sensors, and photocatalysts, among other applications. It is known that 1D ZnO nanowires can be fabricated readily owing to the anisotropic growth of ZnO along the [0001] direction. However, this type of growth results in a decrease in the surface area of the (0001) plane, which plays a vital role not only in UV lasing but also in the photocatalytic process. Thus, we attempted to synthesize ZnO crystals with an increased polar surface area by controlling the crystal growth process. The purpose of this review is to propose a simple route for the synthesis of plate-like ZnO crystals with highly enhanced polar surfaces and to explore their feasibility for use in UV lasers as well as as a photocatalyst and antibacterial agent. In addition, we highlight the recent progress made in the pilot-scale synthesis of plate-like ZnO crystals for industrial applications.

• Journal of Sensor Science and Technology
• /
• v.14 no.5
• /
• pp.313-321
• /
• 2005

Spray combustion has been used in many industrial fields, for instance, such as diesel engines, gas turbines and industrial furnaces, and furthermore various measurement techniques have been applied to elucidate the phenomenon of spray combustion. In order to measure simultaneously the droplet velocity and the droplet size of spray, phase doppler anemometry (PDA) was frequently used in spray combustion. However, the measurement error is occurred due to existence of flame, which is considered as influencing the precision of measurement. Therefore, the purpose of this study is experimentally to conduct the systematic evaluation on the measurement error when PDA measurement is applied to combustion field.

• Journal of Sensor Science and Technology
• /
• v.14 no.5
• /
• pp.357-361
• /
• 2005

Low-stress silicon nitride (LSN) thin films with embedded metal line have been developed as free standing structures to keep microspheres in proper locations and localized heat source for application to a chip-based sensor array for the simultaneous and near-real-time detection of multiple analytes in solution. The LSN film has been utilized as a structural material as well as a hard mask layer for wet anisotropic etching of silicon. The LSN was deposited by LPCVD (Low Pressure Chemical Vapor Deposition) process by varing the ratio of source gas flows. The residual stress of the LSN film was measured by laser curvature method. The residual stress of the LSN film is 6 times lower than that of the stoichiometric silicon nitride film. The test results showed that not only the LSN film but also the stack of LSN layers with embedded metal line could stand without notable deflection.

• Journal of Sensor Science and Technology
• /
• v.20 no.4
• /
• pp.230-233
• /
• 2011

In this paper, highly-efficient optical gating in a junction device based on vanadium dioxide($VO_2$) thin film grown by a sol-gel method was investigated as a gate terminal of a three-terminal device using infrared light with a wavelength of ~1554.6 nm. Due to the photoinduced phase transition, the threshold voltage of the $VO_2$ junction device, at which the device current abruptly jumps, could be tuned with a sensitivity of ~96.5 V/W by adjusting the optical power of the infrared light directly illuminating the device. Compared with the tuning efficiency of the previous device fabricated using $VO_2$ thin film deposited by a pulsed laser deposition method, the threshold voltage of this device could be tuned by ~76.8 % at an illumination power of ~39.8 mW resulting in a tuning efficiency of ~1.930 %/mW, which is ~4.9 times larger than the previous device.

• Journal of Sensor Science and Technology
• /
• v.18 no.3
• /
• pp.207-209
• /
• 2009

This paper describes the characteristics of poly 3C-SiC micro resonators with $3{\times}10^{17}{\sim}1{\times}10^{19}cm^{-3}$ doping concentrations. The 1.2 ${\mu}m$ thick cantilever and the 0.4 ${\mu}m$ thick doubly clamped beam resonators with different lengths were fabricated using poly 3C-SiC thin films. The characteristics of poly 3C-SiC micro resonators were evaluated by quartz and a laser vibrometer in vacuum at room temperature. The resonant frequencies of micro resonators decreased with doping concentrations owing to reduction in the Young's modulus of poly 3C-SiC thin films. It was confirmed that the resonant frequencies of poly 3C-SiC resonators are controllable by doping concentrations. Therefore, poly 3C-SiC resonators could be applied to MEMS devices and bio/chemical sensor applications.

• Journal of Sensor Science and Technology
• /
• v.17 no.6
• /
• pp.425-428
• /
• 2008

This paper describes the resonant characteristics of polycrystalline SiC micro resonators. The $1{\mu}m$ thick polycrystalline 3C-SiC cantilevers with different lengths were fabricated using a surface micromachining technique. Polycrystalline 3C-SiC micro resonators were actuated by piezoelectric element and their fundamental resonance was measured by a laser vibrometer in vacuum at room temperature. For the $100{\sim}40{\mu}m$ long cantilevers, the fundamental frequency appeared at $147.2kHz{\sim}856.3kHz$. The $100{\mu}m$ and $80{\mu}m$ long cantilevers have second mode resonant frequency at 857.5.kHz and 1.14.MHz, respectively. Therefore, polycrystalline 3C-SiC resonators are suitable for RF MEMS devices and bio/chemical sensor applications.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.4
• /
• pp.93-99
• /
• 2011

This paper presents a new type of optical silicon accelerometer using deep reactive ion etching (DRIE) and micro-stereolithography technology. Optical silicon accelerometer is based on a mass suspended by four vertical beams. A vertical shutter at the end of the mass can only moves along the sensing axis in the optical path between two single-mode optical fibers. The shutter modulates intensity of light from a laser diode reaching a photo detector. With the DRIE technique for (100) silicon, it is possible to etch a vertical shutter and beam. This ensures low sensitivity to accelerations that are not along the sensing axis. The microstructure for sensor packaging and optical fiber fixing was fabricated using micro stereolithography technology. Designed sensors are two types and each resonant frequency is about 15 kHz and 5 kHz.