• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.2
• /
• pp.103-109
• /
• 2012

Fish generates large thrust through an oscillating motion with a compliant joint of caudal fin. The compliance of caudal fin affects the thrust generated by the fish. Due to the flexibility of the fish, the fish can generate a travelling wave motion which is known to increase the efficiency of the fish. However, a detailed research on the relationship between the flexible joint and the thrust generation is needed. In this paper, the compliant joint of a caudal fin is implemented in the driving mechanism of a robotic fish. By varying the driving frequency and stiffness of the compliant joint, the relationship between the thrust generation and the stiffness of the flexible joint is investigated. In general, as the frequency increases, the thrust increases. When higher driving frequency is applied, higher stiffness of the flexible joint is needed to maximize the thrust. The bending angles between the compliant joint and the caudal fin are compared with the changes of the thrust in one cycle. This result can be used to design the robotic fish which can be operated at the maximum thrust condition using the appropriate stiffness of the compliant joint.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.5
• /
• pp.476-482
• /
• 2009

The effect of pintle shape on the thrust level of pintle-nozzle Solid Rocket Motor(PNSRM) was studied numerically using the Spalart-Allmaras turbulent model of Fluent. Mass flow rate of PNSRM was always less than theoretical value and the extent of decrease in mass flow rate grew in the large pintle because of increase in the relative boundary layer thickness between pintle body and nozzle wall. The bigger pintle size was, the more thrust of pintle tip pressure was obtained. Meanwhile the more thrust of nozzle and chamber pressure decreased. Hence, total thrust of big pintle was less than a small pintle under same throat area condition. Specific impulse was relatively flat for all pintle shape.

• Tribology and Lubricants
• /
• v.25 no.5
• /
• pp.292-297
• /
• 2009

Air foil thrust bearings are the critical components available on high-efficiency turbomachinery which need an ability to endure the large axial force. Air foil bearings are self-acting hydrodynamic bearings that use ambient air as their lubricant. Since the air is squeezed by the edge of compliance-surface of bearing, hydrodynamic force is generated. In this study, we measured the air film thickness and obtained the minimum film thickness experimentally. To increase the maximum load capacity, compliance of sub-structure was controlled. From numerical analyses, it is seen that, if the air film thickness is distributed more uniformly by variable compliance, the thrust bearings can take more axial load.

• Proceedings of the KIEE Conference
• /
• 2002.11d
• /
• pp.70-72
• /
• 2002

LPM that is used for head driver is problem of miniaturization of construction and cost. This can be achieved by most suitable shape decision. and suitable selection of control system. Specially, in LPM that Full step is mm$\sim$um unit. the large change of thrust receives much effect by tooth number per pole. tooth width and slot width about change of the air gap length. Therefore, this paper presents LPM that use for suitable head driver to reduce of the structure and the cost. to generate maximum thrust of LPM, and finds the proportion of the tooth pitch to tooth width and the slot width about change of the air gap length through FEM analysis. Also, applying different tooth width and slot width that is given as analysis result. this paper presented model that thrust is improved.

• International Journal of Fluid Machinery and Systems
• /
• v.6 no.4
• /
• pp.213-221
• /
• 2013

The characteristics of the thrust for ship propulsion equipment directly driven by air compressed by pressure fluctuation in a blower piping system are investigated. The exhaust valve is positioned upon the air ejection hole in the discharge pipe in order to induce the large-scale pressure fluctuation, and the effects of the valve on the pressure in the pipes and the thrust for the propulsive nozzle are examined. The pressure in the pipes decreases immediately after the valve is opened, and it increases just before the valve is closed. The thrust for the propulsive nozzle monotonically increases with increasing number of revolutions and depth. The interfacial wave in the nozzle appears in the frequency of approximately 4Hz, and it is important for the increase of the thrust to synchronize the opening-closing cycle for the exhaust valve with the generation frequency of the interfacial wave. The finite difference lattice Boltzmann method is helpful to investigate the characteristics of the flow in the nozzle.

• Tunnel and Underground Space
• /
• v.19 no.2
• /
• pp.132-145
• /
• 2009

Faults in rock mass have strong influences on the behaviors of rock structure such as rock slope, tunnel and underground space. Thus, it is very important to analyse for the characteristics of fault rocks in design for tunnel. But, due to the limitation of geotechnical investigation in design stages, tunnel engineers have to carry out the face mapping and additional geological survey during tunnel excavation to find the distribution of faults and the engineering properties of faults for support and reinforcement design of tunnel. In this study, various geological survey and field tests were carried out to analyse the characteristics of the large thrust fault zone through the large sectional tunnel is constructed in mica-schist region. Also, the distribution of structural geology, the shape of thrust faults and the mechanical properties of fault rock were studied for the reasonable design of the reinforcement and support method for the highly fractured fault zone in the large-span tunnel.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.608-612
• /
• 2009

Technology demonstration models(TDM) of a 75-$ton_f$ liquid rocket engine(LRE) thrust chamber were manufactured on the basis of development technologies of 30-$ton_f$ LRE. It was confirmed that some machining and welding technologies which were aimed to be verified through the manufacturing of demonstration models could be applied to the thrust chamber 75-$ton_f$-class. New designed mixing head part was manufactured by means of new process. The manufacturing process and technologies established through TDM's will improve the reliability of manufacturing process of large LRE thrust chamber.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.4
• /
• pp.19-27
• /
• 2021

In this study, a high-pressure subsacle thrust chamber was developed to verify the core technology for KSLV-II performance enhancement. The core technologies are the design of an injector for high-pressure combustion, development of a combustion stabilization device using the additive manufacturing technique, and the design and fabrication of mixing head and regeneratively cooled combustion chamber. The core technologies, which have been verified through the development of high-pressure subscale thrust chamber, will be used to develop large engine liquid rocket engine thrust chamber in the future.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1115-1121
• /
• 2017

In order to obtain high thrust at the beginning of the flight, the solid rocket motor with large initial burning surface area was designed and tested. From the static firing test, lower initial thrust was obtained compared with the expected thrust based on the internal ballistic prediction due to the negative erosive burning effect which reduced the burning rate estimated by APN Law. In addition, the radial mode combustion instability was observed with 8 fins grain configuration. This instability was removed after the odd number of fins were used.

• Journal of KSNVE
• /
• v.10 no.5
• /
• pp.792-799
• /
• 2000

Aircraft noise in the vicinity of Kimpo international airport has damaged to large number of people who live in communities. This paper investigates noise exposed area due to aircraft flight based on prediction modeling program INM and flight path data. Especially effect on route for aircraft has been considered. Ti also examines noise impact for various flight modes, such as a thrust cutback climb method.