• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.375-375
• /
• 2010

CdTe as an absorber material is widely used in thin film solar cells with the heterostructure due to its almost ideal band gap energy of 1.45 eV, high photovoltaic conversion efficiency, low cost and stable performance. The deposition methods and preparation conditions for the fabrication of CdTe are very important for the achievement of high solar cell conversion efficiency. There are some rearranged reports about the deposition methods available for the preparation of CdTe thin films such as close spaced sublimation (CSS), physical vapor deposition (PVD), vacuum evaporation, vapor transport deposition (VTD), closed space vapor transport, electrodeposition, screen printing, spray pyrolysis, metalorganic chemical vapor deposition (MOCVD), and RF sputtering. The RF sputtering method for the preparation of CdTe thin films has important advantages in that the thin films can be prepared at low growth temperatures with large-area deposition suitable for mass-production. The authors reported that the optical and electrical properties of CdTe thin film were closely connected by the thickness-uniformity of the film in the previous study [1], which means that the better optical absorbance and the higher carrier concentration could be obtained in the better condition of thickness-uniformity for CdTe thin film. The thickness-uniformity could be controlled and improved by the some process parameters such as vacuum level and RF power in the sputtering process of CdTe thin films. However, there is a limitation to improve the thickness-uniformity only in the preparation process [1]. So it is necessary to introduce the external or additional method for improving the thickness-uniformity of CdTe thin film because the cell size of thin film solar cell will be enlarged. Therefore, the authors firstly applied the chemical mechanical polishing (CMP) process to improving the thickness-uniformity of CdTe thin films with a G&P POLI-450 CMP polisher [2]. CMP process is the most important process in semiconductor manufacturing processes in order to planarize the surface of the wafer even over 300 mm and to form the copper interconnects with damascene process. Some important CMP characteristics for CdTe were obtained including removal rate (RR), WIWNU%, RMS roughness, and peak-to-valley roughness [2]. With these important results, the CMP process for CdTe thin films was performed to improve the thickness-uniformity of the sputtering-deposited CdTe thin film which had the worst two thickness-uniformities of them. Some optical properties including optical transmittance and absorbance of the CdTe thin films were measured by using a UV-Visible spectrophotometer (Varian Techtron, Cary500scan) in the range of 400 - 800 nm. After CMP process, the thickness-uniformities became better than that of the best condition in the previous sputtering process of CdTe thin films. Consequently, the optical properties were directly affected by the thickness-uniformity of CdTe thin film. The absorbance of CdTe thin films was improved although the thickness of CdTe thin film was not changed.

• Journal of Korean Society of Forest Science
• /
• v.84 no.2
• /
• pp.151-165
• /
• 1995

This study was conducted to establish a systematized taxonomic problems of through the leaf morphological characters and leaf venation patterns, and stomatal cell patterns and cell characteristics of abaxial and adaxial surface of the leaflets by SEM, of 6 native species in Korea and 2 foreign species of the Genus Rhus in the Family Anacardiaceae. The results obtained from this study are summarized as followings: 1. Morphological study measured 32 characters of leaves from herbarium specimen and field-collected samples for each species. The results of cluster analysis based on the Euclidean distance showed that the species could be classified into 3 groups: R. sylvestris. R. typhina, R. succedanea: R. trichocarpa. R. chinensis. R. verniciflua: and R. ambigua. R. radicans subsp. orientale, Analysis of principal components showed 5 groups: The major factors in the first principal component group was length of petiole of the terminal leaflets, that in the second group angle of left side in the terminal leaflet bash, that in the third group area ratio between first and terminal leaflets, that in the forth group angle ratio between right and left side in the terminal leaflet base, and that in the fifth group was angle of main and secondary vein at midrib of terminal leaflet. Cumulative contribution by the first, second and third principal component group was explained with 82.6%, a large percent of all information. 2. The leaf venation pattern investigated using soft X-ray photography revealed clado-and reticulo-camptodromous types according to branching angle of the secondary vein. And three groups by the developing degree of secondary vein were R. trichocarpa, R. ambigua. R. chinensis, R. typhina; R. radicans subsp. onentale, R. succedanea, R. verniciflua: and R. sylvestris. Classification key for the Rhus of Korean-native Anacardiaceae was made by the venation pattern and devevoping degree of the secondary vein. 3. The stomatal cell patterns were greatly classified into paracytic and anomocytic types, specific among species according to stomatal and subsidiary cell patterns, and various differences among the species was determined. Microstructure of the adaxial and abaxial surfaces could be divided into synclinal and anticlinal cell wall patterns, and were specific-species. Stomatal cells of R. chinensis were surrounded with characterized villus-like cells.

• Asia pacific journal of information systems
• /
• v.19 no.3
• /
• pp.125-150
• /
• 2009

RFID(Radio Frequency IDentification) is a wireless frequency of recognition technology that can be used to recognize, trace, and identify people, things, and animals using radio frequency(RF). RFID will bring about many changes in manufacturing and distributions, among other areas. In accordance with the increasing importance of RFID techniques, great advancement has been made in RFID studies. Initially, the RFID research started as a research literature or case study. Recently, empirical research has floated on the surface for announcement. But most of the existing researches on RFID adoption have been restricted to a dichotomous measure of 'adoption vs. non-adoption' or adoption intention. In short, RFID research is still at an initial stage, mainly focusing on the research of the RFID performance, integration, and its usage has been considered dismissive. The purpose of this study is to investigate which factors are important for the RFID adoption and implementation with organizational resources. In this study, the organizational resources are classified into either finance resources or IT knowledge resources. A research model and four hypotheses are set up to identify the relationships among these variables based on the investigations of such theories as technological innovations, adoption stage, and organizational resources. In order to conduct this study, a survey was carried out from September 27, 2008 until October 23, 2008. The questionnaire was completed by 143 managers and workers from physical distribution and manufacturing companies related to the RFID in South Korea. 37 out of 180 surveys, which turned out unfit for the study, were discarded and the remaining 143(adoption stage 89, implementation stage 54) were used for the empirical study. The statistics were analyzed using Excel 2003 and SPSS 12.0. The results of the analysis are as follows. First, the adoption stage shows that perceived benefits, standardization, perceived cost savings, environmental uncertainty, and pressures from rival firms have significant effects on the intent of the RFID adoption. Further, the implementation stage shows that perceived benefits, standardization, environmental uncertainty, pressures from rival firms, inter-organizational cooperation, and inter-organizational trust have significant effects on the extent of the RFID use. In contrast, inter-organizational cooperation and inter-organizational trust did not show much impact on the intent of RFID adoption while perceived cost savings did not significantly affect the extent of RFID use. Second, in the adoption stage, financial issues had adverse effect on both inter-organizational cooperation and the intent against the RFID adoption. IT knowledge resources also had a deterring effect on both perceived cost savings and the extent of the RFID adoption. Third, in the implementation stage, finance resources had a moderate effect on environmental uncertainty and extent of RFID use while IT knowledge resources had also a moderate effect on perceived cost savings and the extent of the RFID use. Limitations and future research issues can be summarized as follows. First, it is difficult to say that the sample is large enough to be representative of the population. Second, because the sample of this study was conducted among manufacturers only, it may be limited in analyzing fully the effect on the industry as a whole. Third, in consideration of the fact that the organizational resources in the RFID study require a great deal of researches, this research may deem insufficient to fulfill the purpose that it initially set out to achieve. Future studies using performance research are, therefore, needed to help better understand the organizational level of the RFID adoption and implementation.

• Korean Journal of Remote Sensing
• /
• v.36 no.5_2
• /
• pp.989-1006
• /
• 2020

Building change monitoring based on building detection is one of the most important fields in terms of monitoring artificial structures using high-resolution multi-temporal images such as CAS500-1 and 2, which are scheduled to be launched. However, not only the various shapes and sizes of buildings located on the surface of the Earth, but also the shadows or trees around them make it difficult to detect the buildings accurately. Also, a large number of misdetection are caused by relief displacement according to the azimuth and elevation angles of the platform. In this study, object-based building detection was performed using the azimuth angle of the Sun and the corresponding main direction of shadows to improve the results of building change detection. After that, the platform's azimuth and elevation angles were used to detect changed buildings. The object-based segmentation was performed on a high-resolution imagery, and then shadow objects were classified through the shadow intensity, and feature information such as rectangular fit, Gray-Level Co-occurrence Matrix (GLCM) homogeneity and area of each object were calculated for building candidate detection. Then, the final buildings were detected using the direction and distance relationship between the center of building candidate object and its shadow according to the azimuth angle of the Sun. A total of three methods were proposed for the building change detection between building objects detected in each image: simple overlay between objects, comparison of the object sizes according to the elevation angle of the platform, and consideration of direction between objects according to the azimuth angle of the platform. In this study, residential area was selected as study area using high-resolution imagery acquired from KOMPSAT-3 and Unmanned Aerial Vehicle (UAV). Experimental results have shown that F1-scores of building detection results detected using feature information were 0.488 and 0.696 respectively in KOMPSAT-3 image and UAV image, whereas F1-scores of building detection results considering shadows were 0.876 and 0.867, respectively, indicating that the accuracy of building detection method considering shadows is higher. Also among the three proposed building change detection methods, the F1-score of the consideration of direction between objects according to the azimuth angles was the highest at 0.891.

• Tuberculosis and Respiratory Diseases
• /
• v.41 no.4
• /
• pp.389-396
• /
• 1994

Background : The two most important purposes of fiberoptic bronchoscopy in lung cancer patients are obtaining tissue diagnosis and staging. The direct sign of lung cancer on FOB includes visible tumor, with smooth or nodular surface, with or without necrosis and infiltration. Variant cell types of lung cancer have their characteristic biological behaviors respectively. For example, squamous cell carcinoma grows slowly, invades locally and has easy necrosis resulting in cavitation, whereas adenocarcinoma shows early metastasis, small cell carcinoma shows rapid growth and higher early metastasis rate. Based on this, it could be hypothesized that each cell type may have characteristic bronchoscopic finding. Method : To answer this question, we reviewed 106 cases which were diagnosed as primary lung cancer and had bronchoscopically visible specific cancerous lesions. Results : The results were as follows. 1) Squamous cell carcinoma accounted for 66 cases(62.2%), adenocarcinoma 15 cases(14.2%), large cell carcinoma 3 cases(2.8%). 2) The endobronchial tumor lesion was arbitrarily classified into 5 types according to gross characteristics. Type A, multilobulating mass with necrosis, accounted for 24.5%, type B, multilobulating mass without necrosis, 25.5%, type C, round beefy mass, 9.4%, type D, infiltration with mucosal irregularity, 6.6%, and type E, infiltration without mucosal irregularity, 34%. 3) The analysis of correlation between endobronchial tumor pattern and specific cell type revealed that squamous cell carcinoma had relation with the morphologic type B and small cell carcinoma had relation with the morphologic type E, but adenocarcinoma had no preponderance in morphologic type. The gross appearance had influence on the diagnostic yields of biopsies and the diagnostic yields of lobulating mass types(type A, B) were higher than those of other types. Conclusion : From the above observations, it could be concluded that squamous cell carcinoma and small cell carcinoma have relations with specific types of bronchoscopic morphology, but not the case in adenocarcinoma.

• Journal of the Korean earth science society
• /
• v.32 no.3
• /
• pp.276-293
• /
• 2011

In this study a modeling system consisting of Weather Research and Forecasting (WRF), Sparse Matrix Operator Kernel Emissions (SMOKE), the Community Multiscale Air Quality (CMAQ) model, and the CMAQ-Model of Aerosol Dynamics, Reaction, Ionization, and Dissolution (MADRID) model has been applied to estimate enhancements of $PM_{10}$ during Asian dust events in Korea. In particular, 5 experimental formulas were applied to the WRF-SMOKE-CMAQ (MADRID) model to estimate Asian dust emissions from source locations for major Asian dust events in China and Mongolia: the US Environmental Protection Agency (EPA) model, the Goddard Global Ozone Chemistry Aerosol Radiation and Transport (GOCART) model, and the Dust Entrainment and Deposition (DEAD) model, as well as formulas by Park and In (2003), and Wang et al. (2000). According to the weather map, backward trajectory and satellite image analyses, Asian dust is generated by a strong downwind associated with the upper trough from a stagnation wave due to development of the upper jet stream, and transport of Asian dust to Korea shows up behind a surface front related to the cut-off low (known as comma type cloud) in satellite images. In the WRF-SMOKE-CMAQ modeling to estimate the PM10 concentration, Wang et al.'s experimental formula was depicted well in the temporal and spatial distribution of Asian dusts, and the GOCART model was low in mean bias errors and root mean square errors. Also, in the vertical profile analysis of Asian dusts using Wang et al's experimental formula, strong Asian dust with a concentration of more than $800\;{\mu}g/m^3$ for the period of March 31 to April 1, 2007 was transported under the boundary layer (about 1 km high), and weak Asian dust with a concentration of less than $400\;{\mu}g/m^3$ for the period of 16-17 March 2009 was transported above the boundary layer (about 1-3 km high). Furthermore, the difference between the CMAQ model and the CMAQ-MADRID model for the period of March 31 to April 1, 2007, in terms of PM10 concentration, was seen to be large in the East Asia area: the CMAQ-MADRID model showed the concentration to be about $25\;{\mu}g/m^3$ higher than the CMAQ model. In addition, the $PM_{10}$ concentration removed by the cloud liquid phase mechanism within the CMAQ-MADRID model was shown in the maximum $15\;{\mu}g/m^3$ in the Eastern Asia area.

• Journal of Yeungnam Medical Science
• /
• v.15 no.1
• /
• pp.55-66
• /
• 1998

Pathophysiological mechanism of hemorrhagic fever with renal syndrome (HFRS) is not fully understood. Major clinical findings of HFRS patients are widespread hemorrhage, acute renal failure and shock. Basic lesion is vascular injury with microvascular hemorrhage and relatively little inflammation. According to autopsy findings, renal medulla shows focal hemorrhage, tubular necrosis and interstitial mononuclear infiltrates. The predominant cell type in the renal and pulmonary interstitium is a fibroblast and it participates in the healing process at the injury site by secreting a large amount of extracellular matrix proteins. Cultured human lung fibroblasts and Mongolian gerbil fibroblasts were known to be good host cells for the hantaan virus. It is possible that not only the endothelial cell but also the fibroblast is a target of Hantaan virus and the fibroblast might be involved in the pathogenesis and the healing process in HFRS. Integrins are adhesion molecules, and act as receptors for many extracellular matrix proteins. Recently, there are many reports that cell surface integrins influence on some viral infections or reversely viruses influence on the expression of integrins. The ${\alpha}_5{\beta}_1$ integrin is a major receptor for the fibronectin which is an important extracellular matrix protein secreted by fibroblasts. In this study, the role of ${\alpha}_5{\beta}_1$ integrin in the infection of Hantaan virus was examined by using anti-${\alpha}_5{\beta}_1$, integrin, anti-${\alpha}_5$ integrin and anti-${\beta}_1$, integrin antibodies in chicken embryo fibroblasts (CEF) and Mongolian gerbil fibroblasts(MGF). The treatment of anti-${\alpha}_5{\beta}_1$, integrin antibody in CEF reduced the virion titers 26.8% and the amount of nucleocapsid N protein 32.6% when compared with control CEF. When MGF were treated with anti-${\alpha}_5$, anti-${\beta}_1$ and anti-${\alpha}_5{\beta}_1$ integrin antibodies, virion titers were reduced by 26.5%, 29.4% and 28.7% and the amount of nucleocapsid N protein were reduced by 65.2%, 59.7% and 72.6%. These results suggested that ${\alpha}_5{\beta}_1$ integrin might act as a receptor for the Hantaan virus or blocking of ${\alpha}_5{\beta}_1$ integrin influences on the viral replication in CEF and MGF. It is also possible that the blocking of only one subunit of integrin represents similar results in that of whole molecule.

• Journal of Korean Society of Forest Science
• /
• v.58 no.1
• /
• pp.41-47
• /
• 1982

The large devastated land in Young-il district, Gyeongsangbusdo, had been existed for a long time, and the Korean government had invested 3.8 billion won to control soil erosion of the area for 5 years from 1973 to 1977. This research was to investigate the changes of the soil profile and vegetation structure in the 3rd, 6th and 9th years since soil erosion control had implemented. The results obtained in this study are as follows: 1) The thickness of the litter layer (L), the fermentation layer(F), the humified layer(H) and the surface soil layer(S) increased with increasing years after implements soil erosion control project had started. 2) The H layer was not showed for the three years since the project had implemented but was in the sixty year. 3) The soil chemical elements including the organic matter and total nitrogen increased with increasing years after the project had started, the amounts of organic matter and total nitrogen were three and seven times higher respectively in the nineth year after project had started. The amounts of organic matter and total nitrogen were three and seven times higher, respectively in the nineth year after project started than those before. 4) Among the grasses and trees which had been sowed or planted during project period, the summed domination ratios for arundinella hirta var ciliare. Themeda japonica, Cymbopogen goeringi and Lespedeza bicolor decreased rapidly, while those for Robinia pesudoacacia and Pinus densiflora increased with increasing years after the project started. 5) The appearance of Quercus seedlings suited to this area and Pinus densiflora seedling which is a subclimax species increased with increasing years after the project started.

• The korean journal of orthodontics
• /
• v.33 no.4 s.99
• /
• pp.307-317
• /
• 2003

Conventional osseointegrated titanium implants have many limitations; large size, limited location for placement of the implant, severity of the surgery, discomfort of initial healing, difficulty of oral hygiene and uncontrollable force direction. Recently titanium miniscrew and miniplate have been used for an alternative to conventional dental implant. But in relation to miniplate, miniscrew has disadvantages in that more potential inflammation, light orthodontic force application and limited orthodontic application. This study was conducted to evaluate the effectiveness of miniplate by observing the reactions of peri-implant tissues to early orthodontic and orthopedic loading of titanium miniplate. In four adult beagle dogs 10 miniplates were inserted into the alveolar bone using 20 osseointegrated titanium screws. 4 miniplates were placed in two dogs(dogA, B) and 6 miniplates in two dogs(dogC, D). In dogA, B miniplates were loaded with 200gm of force immediately after placement for 15 weeks. In dogc, D, miniplates were loaded with 400gm of force immediately after placement for 8 weeks. Miniplates of dogA were removed, dogA was healed for 4 weeks, and the area which was removed of miniscrew was examined. Following an observation period, the miniplates including miniscrews and the surrounding bone of dogB and dogC, D were removed, respectively. Undecalcified section along the long axis of miniscrews were made and the degree of osseointegration was examined under the light microscope. The results were as follows. 1. In the histologic features there was direct contact between bone and miniscrew in all groups except one, dogC control group. The loaded miniscrew demonstrated only a slight increase of the osseous proximaty when compared with unloaded miniscrew 2. There was no significant difference of the osseointegration of Peri-miniscrew surface between dogB and dogC, D. But dogB showed slightly more increased bone apposition than dogC, D 3. The gingiva overlapping the miniplate and miniscrew showed no inflammatory sign in clinical and histological aspects. 4. The impaled hard and soft tissues at the area which was removed of miniscrews showed good healing without inflammatory reaction. 5. The mobility showed slight increase in un-loaded miniplate but that was insignificant. Based on the results of this study, miniplate(C-tube) can be used as a firm osseous orthodontic and orthopedic anchorage unit immediately after insertion.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.9 no.3
• /
• pp.131-140
• /
• 2006

Suspended particulate matter and organic carbon were measured in the Mankyoung river estuary in February, May, July and August 2003. There was a large variance in river discharge between the dry season of February and May and the wet season of July and August. The influx of dissolved organic carbon into the estuary was $8.16{\times}10^2tonC\;month^{-1}$ in the dry season and $5.77{\times}10^3tonC\;month^{-1}$ in the wet season. The influx of particulate organic carbon was $9.37{\times}10^2tonC\;month^{-1}$ and $3.14{\times}10^4tonC\;month^{-1}$ in the dry and wet seasons, respectively. Especially, dissolved organic carbon in the northern part of the site inside the dike was increased in July when torrential rainfall was high. In the research, the distribution of dissolved organic carbon showed conservative behavior with the salinity gradient in the estuary, suggesting that physical mixing between seawater and freshwater dominates the distribution pattern of the dissolved organic carbon in the system. However 60 to 90% of the particulate organic carbon introduced into the estuary was removed from the surface water at the upper estuarine mixing zone of low salinities, showing non-conservative behavior similar with suspended particulate matte r. The completion of the Saemangum Dike is likely to inhibit the exchange of materials between open sea and the Mankyoung estuary. This suggests that the oxidation of organic carbon in the bottom of the estuary may exhaust dissolved oxygen in the confined environment.