• 콘크리트학회논문집
• /
• 제22권6호
• /
• pp.825-832
• /
• 2010

철근콘크리트 구조물은 위험 단면이 휨강도에 도달하더라도 이 단면에서 소성힌지가 형성되어 휨모멘트가 재분배되어 곧바로 파괴에 도달하지 않는다. 이러한 소성힌지 영역에서 발생하는 비탄성 변형에 의해 소성 회전이 발생한다. 소성힌지길이는 주로 재료 특성에 영향을 받는다. 이 연구에서는 유로코드2에서 제시하고 있는 재료 모델로부터 산정된 휨곡률 분포로부터 소성힌지길이와 소성회전각을 일관되게 산정하였다. 재료 모델의 한계값 즉, 콘크리트 극한변형률, 철근 극한변형률 및 철근의 경화비(k)가 소성회전능력에 미치는 영향을 분석하였다. 해석 결과 콘크리트 극한변형률 및 철근 극한변형률이 증가함에 따라 소성회전능력이 증가하였고 특히, 철근의 경화비(k)가 증가함에 따라 소성 회전각은 크게 증가되는 것으로 나타났다. 따라서 각 재료 모델의 한계값 결정에 세심한 주의가 필요할 것으로 나타났다.

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 1999년도 PROCEEDINGS OF 99 INTERNATIONAL CONFERENCE OF THE KACG AND 6TH KOREA·JAPAN EMG SYMPOSIUM (ELECTRONIC MATERIALS GROWTH SYMPOSIUM), HANYANG UNIVERSITY, SEOUL, 06월 09일 JUNE 1999
• /
• pp.81-114
• /
• 1999

The strain, surface and inerfacial energies of III-V ternary systems were calculated for three kinds of structure modes: the Frank-van der Merwe (FM) mode, the Stranski-Krastanov (SK) mode an the Volmer-Wever (VW) mode. The free energy for each mode was estimated as functions of the thickness and composition or lattice misfit. Through comparison of the free energy of each mode, it was found that the thickness-composition phase diagrams of III-V ternary systems can be determined only by considering the balance of the free energy and three kinds of structure modes appear in the phase diagrams. The SK mode appears only when the lattice misfit is large and/or the lattice layer is thick. The most stable structure of the SK mode is a cluster with four lattice layers or minimum thickness on a wetting layer of increasing lattice layers. The VW mode appears when the lattice misfit is large and the lattice layer is thin and only in the InPSb/InP and GaPSb/GaP systems which have the largest lattice misfit of III-V ternary systems. The stable region of the SK mode in the GaPSb/GaP and InPSb/InP phase diagrams is largest of all because the composition dependence of the strain energy of these systems is stronger than that of the other systems. The critical number of lattice layers below which tow-dimensional (2D) layers precede the three-dimensional (3D) nucleation in the SK mode at x=1.0 depnds on the lattice misfit.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권1호
• /
• pp.33-41
• /
• 2008

Bearing damages by shaft misalignment have frequently been happened in marine ships. Specially. after stern tube bearing damage and failure for large crude oil carriers have been reported several times. However. the bearing reaction of the after stern tube bearing cannot be measured by jack-up test due to the hull structure condition. Therefore, when the jack-up test is used for the bearing reaction measurements, the bearing reaction for the after stern tube bearing obtained from the theoretical calculation method have to be used. In this paper, the shaft alignment on the large oil crude carrier is theoretically calculated and the differences between the calculated and actual installed bearing reaction values are compared. The bearing reactions for forward stern tube bearing and intermediate bearing are calculated by the simple formula using the strain gauge bending moments obtained from the measurements. Their reliability is confirmed by comparing the bearing reactions from jack-up test and the bearing reaction for after stern tube bearing is calculated by the same test. Also, the bearing reactions on the after stern tube bearing, forward stern tube bearing and intermediate shaft bearing under all operating conditions are calculated by using the bending moments obtained from the measurements and it is confirmed that the differences of the bearing reaction for all operating conditions are caused from hull deflection. The results of this study should prove useful for the future projects of the alignment calculation including the hull deflection effectiveness.

• 한국자동차공학회논문집
• /
• 제13권5호
• /
• pp.152-162
• /
• 2005

Coolant rubber hoses for automobile radiators can be degraded and thus failed due to the influence of contacting stresses of air and coolant liquid under the thermal and mechanical loadings. In this study, test analysis was carried out for evaluating the degradation and failure mechanisms of coolant hose materials. Two kinds of EPDM rubber materials applicable to the hoses were adopted: commonly-used ethylene-propylene diene monomer(EPDM) rubbers and EPDM rubbers with high resistance against electro-chemical degradation (ECD). An increase of surface hardness and a large reduction of failure strain were shown due to the formation of oxidation layer for the specimens which had been kept in a high temperature air chamber. Coolant ageing effects took place only by an amount of pure thermal degradation. The specimens degraded by ECD test showed a swelling behavior and a considerable increase in weight on account of the penetration of coolant liquid into the skin and interior of the rubber specimens. The ECD induced material softening as well as drastic reduction in strength and failure strain. However EPDM rubbers designed for high resistance against ECD revealed a large improvement in reduction of failure strain and weight. This study finally established a procedure for reliability analysis and evaluation of the degradation and failure mechanisms of EPDM rubbers used in coolant hoses for automobile radiators.

• 한국지반공학회지:지반
• /
• 제12권1호
• /
• pp.21-34
• /
• 1996

이 논문은 일련의 실내시험을 통해 얻어진 삼척 유기질토의 공학적 특성을 제시한 것이다. 액성한계는 시료의 조제방법에 따라 그 값이 현저히 달라진다는 사실을 알게 되었는데 자연상태로 시험한 값이 노건조시켜 얻어진 값보다 1.5내지 4배나 컸다. 유기질토의 응력변형특성은 변형의 증가에 따라 응력이 점진적으로 증가하는 경향을 보였다. 즉 변형율 20%의 강도가 한국산업규격에 규정된 변형을 15%의 강도보다 더 크다는 것을 알 수 있었다. 또한 유기질토의 강도증가율(0.43~0.65)은 점토에 비해 현저히 크다는 사실도 알 수 있었다. 압밀시험 결과 연직 및 수평방향의 투수계수는 거의 같으나 교란시에는 연직방향의 1/2~1/6로 감소된다는 사실도 알게 되었다. 또한 2차 압밀계수는 유기물함량과 함수비가 많을수록 커지며 유기물함량 15%를 기점으로 하여 그 이하에서는 변화폭이 완만하나 그 이상에서는 큰 변화폭을 보인다.

• 한국지반공학회논문집
• /
• 제29권7호
• /
• pp.47-55
• /
• 2013

조립재료의 요소시험에서 장비에 허용되는 조립재료의 입자크기가 실제 현장에서 사용되는 입자크기에 비해 작은 경우가 종종 발생하기 때문에, 이러한 경우에는 시험에 사용되는 재료의 최대입경을 시험장치의 가용 크기까지 축소시켜 시험을 수행하게 된다. 본 연구에서는 이처럼 최대입경 크기를 축소시켜 입도를 조정했을 때, 저변형률에서의 탄성계수에 미치는 영향을 평가하기 위해 대형반복삼축압축시험을 수행하였다. 본 연구 대상재료의 시험 결과, 입도 조정된 시편들은 원입도 시편의 탄성계수를 과소평가하는 경향이 있었으며, 그 차이는 저변형률에서 더 크게 발생되었다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제3권3호
• /
• pp.223-236
• /
• 1999

The need to monitor and undertake remidial works on large structures has greatly increased in recent years due to the appearance of widespread faults in large structures such as bridges and buildings, etc, of 20 or more years of age. The health condition of structures must be monitored continuously to maintenance the structures. In order to do in-situ monitoring, the sensor is necessary to be embedded in the structures. Fiber optic sensors can be embedded in the structures to get the health information in the structures. The fiber sensor was constructed with $3{\times}3$ fiber couplers to sense the multi-point strains and failure instants. The 4 RC (reinforced concrete) beams were made to 2 of A type, 2 of B type beams. These beams were reinforced by the reinforcing bars, and were tested under the flexural loading. The behavior of the beams was simultaneously measured by the fiber optic sensors, electrical strain gages, and LVDT. The states of the beams were interpreted by these all signals. By these experiments, There were verified that the fiber optic sensors could measure the structural strains and failure instants of the RC beams, The fiber sensors were well operated until the failure of the beams. It was shown that the strains of the reinforcing steel bar can be used to monitor the health condition of the beams through the flexural test of RC beams. On the other words, the results were arrived that the two strains in the reinforcing bar measured at the same point can give the information of the structural health status. Also, the failure instants of beams were well detected from the fiber optic filtered signals.

• 한국재난정보학회 논문집
• /
• 제15권2호
• /
• pp.186-197
• /
• 2019

연구목적: 본 연구에서는 대변형 효과를 구현할 수 있는 유한요소 해석기법을 기반으로 반복하중에 의한 스테인리스강의 이력거동을 정확하게 평가할 수 있는 비선형 반복소성 손상모델을 개발하였다. 연구방법: 개선된 운동경화 모델과 등방경화 법칙을 연계하여 반복하중 하에서의 재료의 거동을 모사하는데 필요한 반복소성 모델을 개발하였으며, 이를 비선형 손상모델과 결합하였다. 연구결과 및 결론: 제안된 비선형 손상모델을 검증하기 위하여 변형률 제어 단조 및 반복하중 시험을 모사하였으며, 이를 통한 해석결과를 시험결과와 비교하였다. 비교 결과, 본 연구에서 제안한 비선형 손상모델은 스테인리스강의 반복하중 하에서의 이력거동을 정확하게 모사할 수 있음을 확인하였다.

• Earthquakes and Structures
• /
• 제20권1호
• /
• pp.109-122
• /
• 2021

Significant progress in the oil and gas industry advances the application of pipeline into an intelligent era, which poses rigorous requirements on pipeline safety, reliability, and maintainability, especially when crossing seismic zones. In general, strike-slip faults are prone to induce large deformation leading to local buckling and global rupture eventually. To evaluate the performance and safety of pipelines in this situation, numerical simulations are proved to be a relatively accurate and reliable technique based on the built-in physical models and advanced grid technology. However, the computational cost is prohibitive, so one has to wait for a long time to attain a calculation result for complex large-scale pipelines. In this manuscript, an efficient and accurate surrogate model based on machine learning is proposed for strain demand prediction of buried X80 pipelines subjected to strike-slip faults. Specifically, the support vector regression model serves as a surrogate model to learn the high-dimensional nonlinear relationship which maps multiple input variables, including pipe geometries, internal pressures, and strike-slip displacements, to output variables (namely tensile strains and compressive strains). The effectiveness and efficiency of the proposed method are validated by numerical studies considering different effects caused by structural sizes, internal pressure, and strike-slip movements.

• Journal of Microbiology and Biotechnology
• /
• 제32권3호
• /
• pp.378-386
• /
• 2022

Scenedesmus obliquus ABC-009 is a microalgal strain that accumulates large amounts of lutein, particularly when subjected to growth-limiting conditions. Here, the performance of this strain was evaluated for the simultaneous production of lutein and biofuels under three different modes of cultivation - photoautotrophic mode using BG-11 medium with air or 2% CO₂ and heterotrophic mode using YM medium. While it was found that the highest fatty acid methyl ester (FAME) level and lutein content per biomass (%) were achieved in BG-11 medium with CO₂ and air, respectively, heterotrophic cultivation resulted in much higher biomass productivity. While the cell concentrations of the cultures grown under BG-11 and CO₂ were largely similar to those grown in YM medium, the disparity in the biomass yield was largely attributed to the larger cell volume in heterotrophically cultivated cells. Post-cultivation light treatment was found to further enhance the biomass productivity in all three cases and lutein content in heterotrophic conditions. Consequently, the maximum biomass (757.14 ± 20.20 mg/l/d), FAME (92.78 ± 0.08 mg/l/d), and lutein (1.006 ± 0.23 mg/l/d) productivities were obtained under heterotrophic cultivation. Next, large-scale lutein production using microalgae was demonstrated using a 1-ton open raceway pond cultivation system and a low-cost fertilizer (Eco-Sol). The overall biomass yields were similar in both media, while slightly higher lutein content was obtained using the fertilizer owing to the higher nitrogen content.