• 한국초전도ㆍ저온공학회논문지
• /
• 제18권4호
• /
• pp.21-24
• /
• 2016

The mechanical properties of REBCO coated conductor (CC) wires under uniaxial tension are largely determined by the thick component layers in the architecture, namely, the substrate and the stabilizer or even the reinforcement layer. Depending on device applications of the CC tapes, it is necessary to reinforce thin metallic foils externally to one-side or both sides of the CC tapes. Due to the external reinforcement of brass foils, it was found that this could increase the reversible strain limit from the Cu-stabilized CC tapes. In this study, the effects of differently hardened brass foil laminate on the electromechanical property of CC tapes were investigated under uniaxial tension loading. The tensile strain dependence of the critical current ($I_c$) was measured at 77 K and self-field. Depending on whether the $I_c$ of CC tapes were measured during loading or after unloading, a reversible strain (or stress) limit could be determined, respectively. The both-sides of the Cu-stabilized CC tapes were laminated with brass foils with different hardness, namely 1/4H, 1H and EH. From the obtained results, it showed that the yield strength of the brass laminated CC tapes with EH brass foil laminate was comparable to the one of the Cu-stabilized CC tape due to its large yield strength even though its large volume fraction. It was found that the brass foil with different hardness was mainly sensitive on the stress dependence of $I_c$, but not on the strain sensitivity due to the residual strain induced in the laminated CC tapes during unloading.

• 한국지반공학회논문집
• /
• 제18권4호
• /
• pp.215-228
• /
• 2002

동반논문(오세붕, 2002)에서는 전체 변형도 영역의 거동을 모델할 수 있는 GUX( 구성모델을 ABAQUS 코드(Hibbit 등, 2001)에 구현하였다. 먼저 정확도 해석을 통하여 동반논문에서 구현한 내재적 응력적분 기법이 해의 정확도를 확보함을 알 수 있었다. GUX 모델은 전응력 개념에 의거한 비등방경화 탄소성 구성모델이므로 완전 배수 또는 비배수 삼축시힘시 응력-변형도 관계를 입력하여 대상문제를 배수 및 비배수조건에 따라 해석할 수 있다. 본 연구에서는 연약지반 및 풍화토 지반상 성토시 안정성 문제와 지반-말뚝계의 축하중 재하시 거동에 대한 예제 해석을 수행하였다. 그리고 대변형 해석을 통하여 기하학적 비선형성을 고려하였고 전체 변형도 거동을 합리적으로 모델하는 GUX 모델을 이용한 결과를 Mises 모델 결과와 비교하였다.

• 센서학회지
• /
• 제32권4호
• /
• pp.238-245
• /
• 2023

0.75(Bi_1/2Na_1/2)TiO₃-0.25SrTiO₃ (BNT-25ST) ceramics with high densities were successfully prepared at a sintering temperature of 1,000℃ by adding a mixture of 1 mol% CuO and 0.5 mol% Na₂CO₃ or 0.5 mol% CuO and 0.25 mol% Na₂CO₃. Double polarization-electric field (P-E) hysteresis curves and sprout-shaped bipolar strain-electric field (S-E) hysteresis curves with small negative strains were observed in the pristine and CuO-added BNT-25ST ceramics whereas the Na₂CO₃-added sample showed similar P-E and S-E curves to a typical ferroelectric. The pristine BNT-25ST ceramics showed an extremely large strain and a large-signal piezoelectric strain constant (d₃₃^*): 0.287 % at 80 kV/cm and 850 pm/V at 20 kV/cm. Similar values, 0.248 % at 80 kV/cm and 655 pm/V at 20 kV/cm, were obtained in the CuO-added sample. However, the pristine and CuO-added samples showed large hysteresis in unipolar S-E curves at an electric field of less than 20 kV/cm. The Na₂CO₃-added sample showed smaller values of the strain and d₃₃^* but displayed a linear change and small hysteresis in the unipolar S-E curve. The co-added sample with CuO and Na₂CO₃ displayed intermediate P-E and S-E hysteresis curves.

• Geomechanics and Engineering
• /
• 제34권4호
• /
• pp.409-424
• /
• 2023

Response of the pipeline crossing fault is considered as the large strain problem. Proper estimation of the pipeline response plays important role in mitigation studies. In this study, an advanced continuum modeling including material non-linearity in large strain deformations, hardening/softening soil behavior and soil-pipeline interaction is applied. Through the application of a fully nonlinear analysis based on an explicit finite difference method, the mechanics of the pipeline behavior and its interaction with soil under large strains is presented in more detail. To make the results useful in oil and gas engineering works, a continuous pipeline of two steel grades buried in two clayey soil types with four different crossing angles of 30°, 45°, 70° and 90° with respect to the pipeline axis have been considered. The results are presented as the fault movement corresponding to different damage limit states. It was seen that the maximum affected pipeline length is about 20 meters for the studied conditions. Also, the affected length around the fault cutting plane is asymmetric with about 35% and 65% at the fault moving and stationary block, respectively. Local buckling is the dominant damage state for greater crossing angle of 90° with the fault displacement varying from 0.4 m to 0.55 m. While the tensile strain limit is the main damage state at the crossing angles of 70° and 45°, the cross-sectional flattening limit becomes the main damage state at the smaller 30° crossing angles. Compared to the stiff clayey soil, the fault movement resulting 3% tensile strain limit reach up to 40% in soft clayey soil. Also, it was seen that the effect of the pipeline internal pressure reaches up to about 40% compared to non-pressurized condition for some cases.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2014년도 제49회 KOSCO SYMPOSIUM 초록집
• /
• pp.211-213
• /
• 2014

Simultaneous measurements of planar laser-induced fluorescence (PLIF) of OH radicals and particle image velocimetry (PIV) were used to investigate the strain rates and OH structure characteristics of turbulent syngas non-premixed jet flames close to blowoff. Mean values of the maximum principal strain rate on OH layer decreases with the axial distance, and its standard deviation is significantly large upstream. Strain rate on stabilization region of the stable flame is only about a half of that of the flame near blowoff.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.267-272
• /
• 1993

This paper presents the performance and problems in analysis method and testing system of Electronic Speckle Pattern Interferometry (ESPI) method, in measuring two-dimensional in-plane displacement. The anyalysis result of measurement by ESPI is quite comparable to that of measurement by strain gauge method. This implieds that the method of ESPI is a very effective tool in non-contact two-dimensional in-planc strain analysis. But there is a controversal point,measurment error. This error is discussed to be affected not by ESPI method itseif, but by its analysis scheme of the interference fringe,where the first-order interpolation has been applied to the points of strain measured. In this case, it is turned out that the more errors would be occured in the large interval of fringe. so, this paper describes a computer method for drawing when the height is available only for some arbitary collection of points, the method is based on a distance-weighted, least-squares approximation technique, with the weight varying with the distance of the data points.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 1998년도 학술발표회 발표논문집
• /
• pp.455-460
• /
• 1998

This study performed to establish tile characteristics of constant rate of strain consolidation(CRSC) tests. The values obtained by the CRCS tests were compared with oedometer tests. From the comparision of the results of oedometer and CRSC tests for soft soil from Haenam, Korea, it was concluded that. 1. When rate of strain is 0.9mm/hr, compression curve of CRSC test was not coincided with those of tile oedometer test, then preconsolidation stress was larger than those of other rates of strain. 2. Permeabilities from CRSC tests and direct measurements were about same each other, but permeabilities from Oedometer tests were large than those from others.

• 대한기계학회논문집A
• /
• 제33권12호
• /
• pp.1357-1365
• /
• 2009

In this study, we enhance the numerical approach of Lee et al.$^{(1)}$ to spherical indentation technique for property evaluation of hyper-elastic rubber. We first determine the friction coefficient between rubber and indenter in a practical viewpoint. We perform finite element numerical simulations for deeper indentation depth. An optimal data acquisition spot is selected, which features sufficiently large strain energy density and negligible frictional effect. We then improve two normalized functions mapping an indentation load vs. deflection curve into a strain energy density vs. first invariant curve, the latter of which in turn gives the Yeoh-model constants. The enhanced spherical indentation approach produces the rubber material properties with an average error of less than 3%.

• Smart Structures and Systems
• /
• 제19권5호
• /
• pp.473-485
• /
• 2017

Ratcheting behavior of $90^{\circ}$ elbow piping subject to internal pressure 20 MPa and reversed bending 20 kN was investigated using experimental method. The maximum ratcheting strain was found in the circumferential direction of intrados. Ratcheting strain at flanks was also very large. Moreover, the effect of temperature on ratcheting strain of $90^{\circ}$ elbow piping was studied through finite element analysis, and the results were compared with room condition ($25^{\circ}$). The results revealed that ratcheting strain of $90^{\circ}$ elbow piping increased with increasing temperature. Ratcheting boundary of $90^{\circ}$ elbow piping was determined by Chaboche model combined with C-TDF method. The results revealed that there was no relationship between the dimensionless form of ratcheting boundary and temperature.

• 한국정밀공학회지
• /
• 제13권8호
• /
• pp.96-101
• /
• 1996

Glass fiber reinforced polymeric composites hold considerable promise for increased use in low cost high volume applications because of the potential for processing by solid phase forming. Unfortunately, because of the wide variety of such materials, inherent bariability in properties, and complex temperature and strain rate dependence, large strain behavior of these materials has not been well characterized. Of particular importance is failure during processing due to localized necking instability, and it is this phenomenon that is primary focus of this study. The strain rate and temperature dependence is used to predict limiting tensile strains, based on Mackinack imperfection theory. Excellent correlation was obtained between theory and experiment, and the results are summarized in the limit strains as a function of temperature and stain rate.