• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.1 s.232
• /
• pp.151-158
• /
• 2005

A characteristic of discharge for a foam spray nozzle with various parameters was investigated. The discharge patterns from a fire foam spray nozzle are important to evenly spray over a maximum possible floor area. Two parameters of a foam spray nozzle were chosen, and compared with those from the standard one. Also, in order to evaluate the performance of discharged foam agents used to protect structures from heat and fire damages, the thermal characteristics of fire-protection foams were experimentally investigated. A simple repeatable test for fire-protection foams subjected to fire radiation was developed. This test involves foam generation equipment, a fire source for heat generation, and data acquisition techniques. Results show that the bubble size of foam is increased by large inside diameter of orifice or closed air hole, but phenomenon of discharge angle and expansion ratio is opposite. For the case of the open air hole, liquid film of a circular cone discharges with formation, growth, split and fine grain. In case of the closed air hole, a pillar of foam solution discharges with that. Though the temperature gradient in the foam increases with increased foam expansion ratio. it is not change with increased intensity of heat flux.

• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.3
• /
• pp.206-221
• /
• 2015

Supercavitation is a modern technique which can be used to surround an underwater vehicle with a bubble in order to reduce the resistance of the vehicle. When the vehicle is at low speed in the deep sea, the cavitation number is relatively big and it is difficult to generate a cavity large enough to envelope the vehicle. In this condition, the artificial cavity, called ventilated cavity, can be used to solve this problem by supplying gas into the cavity and can maintain supercavitating condition. In this paper, a relationship between the ventilation gas supply rate and the cavity shape is determined. Based on the relationship a ventilation rate control is developed to maintain the supercavitating state. The performance of the ventilation control is verified with a depth change control. In addition, dynamics modeling for the supercavitating vehicle is performed by defining forces and moments acting on the vehicle body in contact with water. Simulation results show that the ventilation control can maintain the supercavity of an underwater vehicle at low speed in the deep sea.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.1446-1451
• /
• 2008

The clay found in the river or in any waste water treatment plant usually have a very high content of water. A large amount of sediments hinder the navigation in river. In waste water treatment plant, there is requirement of settling the thick sludge. These problems are overcome by using rapid means of sedimentation and settling. This paper focus on how method of Electrokinetic sedimentation can be made faster. Sedimentation using Electrokinetic phenomenon has been discussed with varied voltage applied and effect and dose of coagulant in increasing the process. The experimental test has been carried out at water content that are generally present in the case of river and small canals carrying waste water. This paper also focus on different heavy metals concentration during the process and the power aspects of process. A series of experiment were done to support the proposed theory and how a bubble formation could hinder the purpose of experiment.

• Resources Recycling
• /
• v.5 no.4
• /
• pp.11-16
• /
• 1996

In the flotation system for deinking process, the ink partcles musl collidc with the air bubbles for adhesion The probability of bubble-particle collision is largely dependent on the hydrodynamic conditions The main reason for the very small ink particles not to be able to float easily may be tound in the hydrodynamic effects, which make small ink particlcs move following the slreamlines around the bubbles rather than achually collide with bubbles. Also. the low floatabdily of the large and heavy ink particles is due to the gravity force and viscous drag which affect uprising molinn of particles through the liquid. Therefore, it is vely important to control not only the surface chemical conditions but the hydrodynamic conditions in practical floialion system

• Journal of The Korean Astronomical Society
• /
• v.28 no.2
• /
• pp.255-264
• /
• 1995

The HII region S140 and the associated molecular cloud L1204 have been observed with 10 molecular transitions, CO (1-0), $^{13}CO$ (1-0), $C^{18}O$ (1-0), CS (2-1), $HCO^+$ (1-0), HCN (1-0), SO (${2_2}-{1_1}$), $SO_2(2_{20}-3_{13})$, OCS (8-7), and $HNCO\;(4_{04}-3_{03})$ with ${\sim}50"$ angular resolutions. More than 7,000 spectra were obtained in total. The morphology of this region shows a massive fragment (the S140 core) and the extended envelope to the northeast. Several gas condensations have been identified in the envelope, having masses of ${\sim}10^{3}M_{\odot}$ and gas number densities of ${\lesssim}10^{4}cm^{-3}$ to $3{\times}10^{5}cm^{-3}$ in their cores. The column densities of the observed molecular species toward the S140 core appear to be the typical warm clouds' abundances. It seems to be that the S140 core and L1204 have been swept up by an expanding shell called the Cepheus bubble. The large value of $L_{IR}$(embedded\;stars)/$M_{cloud}\;{\sim}\;5\;L_{\odot}$/$M_{\odot}$ of the S140 core may suggest that the star formation has been stimulated by the HII region, but the shock velocity and the pressure of the region seem to give a hint of the spontaneous star formation by the self gravity.

• Journal of the Korean Ceramic Society
• /
• v.31 no.4
• /
• pp.375-380
• /
• 1994

Matrices retaining electrolyte in phosphoric acid fuel cell were prepared with SiC to SiC whisker mixing ratios of 1:0.5, 1:1, 1:1.5, 1:2, 1:3 by tape casting method. When viscosity of the slurry was 5.9 poise and the SiC to SiC whisker mixing ratios were 1:1, 1:1.5, 1:2, the ranges of porosity, acid absorbency and bubble pressure were 80~90%, 2.5~6 and 700~2200 mmH2O, respectively. Those ranges are acceptable for a practical electrolyte-retaining matrix. With increasing the mixing ratio of SiC whisker to SiC, the porosity and the vol.% of large pores in the main pore size distribution which is between 1 and 10 ${\mu}{\textrm}{m}$, increased rapidly. Impedance spectroscopy was measured to know characteristics of matrix inside and contact region of matrix to catalyst layer. When the SiC to SiC whisker mixing ratio was 1:2, hydrogen ions were transported in the matrix most effectively because of high ionic conductivity and low activation energy due to high acid absorbency in spite of high interfacial resistance. The cell current density of the cell made using the matrix was 220 mA/$\textrm{cm}^2$ at 0.7 V.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.10
• /
• pp.842-849
• /
• 2006

In this study, the effect of carbon nanotubes (CNTs) on boiling heat transfer is investigated. Three refrigerants of R22, R123, R134a, and water are used as base working fluids and 1% of CNTs by volume is added to the base fluids to study the effect of CNTs. All data are obtained at the pool temperature of $7^{\circ}C$ for all refrigerants and $100^{\circ}C$ for water in the heat flux range of $10{\sim}80\;kW/m^2$. Test results show that CNTs increase the boiling heat transfer coefficients for all fluids. Especially, large enhancement was observed at low heat flutes. With increasing heat flux, however, the enhancement was suppressed due to vigorous bubble generations. Fouling was not observed during the course of this study. Optimum quantity and type of CNTs and their dispersion should be examined for their application in pool boiling heat transfer.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.3
• /
• pp.75-84
• /
• 2018

According to IHS, the overall display market is expected to grow at an average annual rate of 6% from $ 104 billion in 2016, to $ 138 billion in 2021. Among them, the OLED display panel will grow from $ 15 billion to $ 41 billion over the same period, forecasting a high annual growth rate of 22%. However, the refraction index, light leakage, bubble generation, adhesion deterioration, peeling phenomenon, moisture resistance, light transmittance, low turbidity. OCA (optically clear adhesive), which solves problems such as improving the resistance of the conductive film, is largely dependent on imported products. In addition, in 2016, the world market is worth KRW4.3 trillion, and the adhesive market has a large market effect. In this study, we tried to analyze the technical competitiveness of patent and thesis by classifying OCA (optically clear adhesive, optical adhesive) for display panel by curing method. As a result of the study, the amount of patents and papers in Korea was found to be superior to other competitors, but the quality level was low. In particular, it was found that the achievements of the papers in the hot melt field are lacking and the government should expand its support.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.4
• /
• pp.164-170
• /
• 2021

Vanadium redox flow batteries (VRFB) have emerged as large-scale energy storage systems (ESS) due to their advantages such as low cross-contamination, long life, and flexible design. However, Hydrogen evolution reaction (HER) in the negative half-cell causes a harmful influence on the performance of the VRFB by consuming current. Moreover, HER hinders V²⁺/V³⁺ redox reaction between electrode and electrolyte by forming a bubble. To address the HER problem, carbon nanotube/graphite felt electrode (CNT/GF) with oxygen functional groups was synthesized through the hydrothermal method in the H₂SO₄ + HNO₃ (3:1) mixed acid solution. These oxygen functional groups on the CNT/GF succeed in suppressing the HER and improving charge transfer for V²⁺/V³⁺ redox reaction. As a result, the oxygen functional group applied electrode exhibited a low overpotential of 0.395 V for V²⁺/V³⁺ redox reaction. Hence, this work could offer a new strategy to design and synthesize effective electrodes for HER suppression and improving the energy density of VRFB.

• Transactions of Materials Processing
• /
• v.31 no.5
• /
• pp.290-295
• /
• 2022

Recently, the use of high-tech ceramic parts in functional electronic parts, automobile parts and semiconductor equipment parts is increasing. These ceramics materials are required to have high reproducibility, reliability, large size and complex shapes. The researchers initiated the work to develop a new shaping method called gel casting, which allows high performance ceramic materials with a complex shape to be produced. The manufacturing process parameters of gel casting include uniform mixing of the initiator, bubble removal, and slip injection. In this study, we analyzed the dispersion and gelation characteristics according to the change in the additive content of the alumina slurry in the gel casting process. The alumina slurry for gel casting was prepared by mixing a solvent, a monomer and a dispersant through a ball mill. Alumina powder and a gelation initiator were added to the mixed solution, and ball milling was performed for 24 hours. A viscosity of 6,435 cps and a stable zeta potential value were obtained under the conditions of alumina powder content of 55 vol% and dispersant 2.0 wt%. After curing for 12 hours by adding aps 0.1wt%, TEMED 0.2wt%, and Monomer 3, 5wt%, it was possible to separate from the molding cup, confirming that the gelation was completed.