• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.3
• /
• pp.447-452
• /
• 2003

Crevice corrosion is localized form of corrosion usually associated with a stagnant solution on the micro-environmental level. Such stagnant micro environments tend to occur in crevices (shielded areas) such as those formed under gaskets washers insulation material. fastener heads. surface deposits. disbonded coatings. threads. lap joints and clamps. Crevice corrosion is initiated by changes in located electrochemical reaction within the crevice such as a) depletion of inhibitor in the crevice b) depletion of oxygen in the crevice c) a shift to acid conditions in the crevice and d) build-up of aggressive ion species (e.g chloride) in the crevice. In this study. the mechanism of crevice corrosion for Type 430 stainless steel is investigated undercondition that the size of specimen is $15{\times}20\{times}3mm$, in 1N $H_2SO_4$ + 0.05N NaCl solution. and the artificial crevice gap size of 3 x 0.2 x 15 mm. Crevice corrosion is measured under applied potential -300mV(SCE) to the external surface. The obtained result of this study showed that 1) the induced time for initiation of crevice is 750 seconds. 2) potential of the crevice was about from -320mV to -399mV. which is lower than that of external surface potential of -300mV It is considered that potential drop in the crevice is one of mechanisms for the crevice corrosion

• Fashion & Textile Research Journal
• /
• v.2 no.5
• /
• pp.423-429
• /
• 2000

This study was conducted to find out the relationship between skin temperature and clothing temperature in body parts. Four different kinds of fabrics were used in this experiment. These fabrics were a (Ny/Spun, 81.8/18.2%), b (Wool/Poly/span, 50/45/5%), (Wool/Ny/Span70/25/5) and d (Wool/Poly/Span 45/45/10%). The subjects skated at indoor ice rink where the length was 111.12 m, the temperature was $11{\pm}1^{\circ}C$ and the humidity was $70{\pm}10%$. The four an male professional skaters speed was $17{\pm}1$ seclm/lap. Physiological parameters were skin temperature at 4 body points (chest, upper arm, thigh, leg) and clothing temperature at chest was measured every 15 second. Experiment protocol was as follows: resting before skating (5 min.), skating (5 min.), and resting after skating (10 min.). The results were as follows; The mean skin temperature by fabrics shows b > a > d > c. The mean skin temperature began to decline little by little as soon as the subjects entered the indoor ice rink. After they rested for five minutes, they started skating and the mean skin temperature declined widely. After skating, the mean skin temperature increased step by step. It maintained the similar temperature. The value of skin temperature at body points shows Leg > Chest > Upper arm > Thigh. Because of the characteristics of skating uniforms, the skin temperature of the leg is the highest. The skating uniform was designed to have a protective portion in the leg. The chest produces the highest temperature in the body. The comparison of difference values in skin temperature show Thigh > Upper arm > Chest > Leg. While skating in a cold atmosphere, the largest difference value is clothing temperature. The clothing temperature is lower than the skin temperature during skating. The difference value of clothing temperature is larger than the skin temperature of the chest.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.1 s.34
• /
• pp.47-52
• /
• 2005

Worldwide movement for prohibition of Pb usage drives imminent implementation of Pb-free solders in microelectronic packaging industry. Reliability information of Pb-free solders has not been completely constructed yet. One of the potential reliability concerns of Pb-free solders is allotropic transformation of Sn known as tin pest. Volume increase during the formation of tin pest could deteriorate the reliability of solder joints. It was also reported that the addition of soluble elements (i.e. Pb, Bi, and Sb) into Sn can effectively suppress the tin pest. However, the mechanical properties of the tin pest resistant alloys have not been studied in detail. In this study, lap shear creep test was conducted with Sn and Sn-0.7Cu based solder alloys doped with minor amount of Bi or Sb. Shear strain rates of the alloy were generally higher than those of Sn-3.5Ag based alloys. Rupture strains and corresponding Monkman- Grant products were largest for Sn-0.5Bi alloy and smallest for Sn-0.7Cu-0.5Sb alloy. Rupture surface Sn-0.5Bi alloy showed highly elongated $\beta$-Sn globules necked to rupture by shear stresses, while elongation of $\beta$-Sn globules of Sn-0.7Cu-0.5Sb alloy was relatively smaller.

• Radiation Oncology Journal
• /
• v.15 no.2
• /
• pp.129-136
• /
• 1997

Purpose : We analyzed the survival and failure patterns of cervix cancer patients treated with irradiation alone to evaluate our treatment method and to compare with the others Methods and Materials : Two hundred and twenty cervical cancer patients, Stage IB, II A, and II B who completed the planned treatment between Mar 1987 and December 1991 were analyzed retrospectively. The Stage IB patients were restaged to the Stage IB1 and IB2 by the recently revised FIGO classification, Patients were treated with a combination of external irradiation and the intracavitary brachytherapy Determination of the tumor control was done at the time of 6 months Postirradiation. The follow-up time was ranged from 3 to 115 months and the mean was 62 months and the follow-up rate was $93.6\%$(206/220) Results : The overall 5-year survival rate of Stage IB1 (N=50), IB2(N: 15). II A(N=58), and II B(N=97) was $94\%,\;87\%,\;69\%,\;and\;56\%$. respectively. In the univariate analysis of prognostic factors, stage(0.00), initial Hg level (P=0.00), initial TA-4(tumor-associated) antigen level(p= 0.02), initial CEA level(p=0.02), barrel-shaped tumor(p=0.02), whole cervical involvement (0.00), pelvic tyrnphadenopathy(LAP) in CT(p=0.04), and Post-irradiation adiuvant chemotherapy(P=0.00) were statistically significant in survival analysis. In a while multivariate analysis showed that the stage was the most powerful Prognostic indicator and the Post-irradiation chemotherapy factor also showed the statistical significance. The overall local control rate was $81\%$ and by the stage, $100\%$ in Stage IBI, $86.7\%$ in Stage IBS, $84.5\%$ in Stage IIA, and $68.1\%$ in Stage IIB, respectively The overall tumor recurrence rate was $15.5\%$(27/174) and by the stage, $8\%$(4/50) in Stage IB1, $0\%$(0/l3) in Stage IB2, $22.4\%$(l1/49) in Stage II A, and $19.4\%$(12/62) in Stage II B, respectively. Conclusions : We obtained the similar treatment results to the other's ones in early stage cervical cancer patients. But in Stage II B, the local control rate was lower than that of the other institutes and also the survival was poorer. So it seems to be necessary to reevaluate the treatment method in advanced cervical cancer patients.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.15
• /
• pp.6715-6717
• /
• 2015

Background: The purpose of this study was to provide epidemiological and histological data of thyroid cancers in Togo. Materials and Methods: This was a retrospective cross-sectional study of cases of thyroid cancers diagnosed from 2000 to 2014 (15 years) at the pathology laboratory of the Sylvanus Olympio Teaching Hospital of $Lom{\acute{e}}$. All cases of review of a thyroid sample (biopsies, surgical specimens) were collected from the data records of that laboratory. Results: Thyroid cancers represented 1.1% (7930cases) of all cancers registered during the study period. Mean age was $45.4{\pm}0.3$ years and the proportion of females was 78.3%. We identified 92.4% carcinomas and 7.6% lymphomas. Carcinomas were well differentiated in 80 cases and were dominated by the papillary type (47 cases). Metastasis was observed in 13% of patients. The pTNM classification evaluated in 18 cases showed a predominance of grade I (13 cases). Lymphomas were dominated by lymphoma diffuse large B-cell (5 cases). Conclusions: This study is the first global standard for thyroid cancer pathology in Togo. The high frequency of follicular form suggests an unrecognized iodine deficiency. The improvement of the technical platform of the LAP (immunohistochemistry) will increase the diagnosis of rare forms of thyroid cancer.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.41-41
• /
• 2009

To evaluate the applicability of dissimilar joining between Mg and Al alloys in automobile manufacturing process, solid state joining processes such as magnetic pulse welding(MPW), friction stir welding(FSW) and friction spot joining(FSJ) were attempted successfully. MPW process has been concentrated mainly on round section tube to tube and tube to bar welds. AZ31 Mg alloy has been successfully welded to pure Al A1070 as well as to Al alloy A3003. While, for friction stir welding of dissimilar sheet joints, AZ31B/A6061 with the thickness of 2mm were used and a square butt joint with a good quality was obtained at the conditions of 0.8mm/sec of travel speed and tool rotation speed of 850rpm. The maximum tensile strength of 179 MPa, which was about 80 % of the Mg base metal tensile strength, has been obtained. Finally, friction spot joining was attempted to make a dissimilar lap joint between AZ31(0.8mm) and A6061(1mm), while the joint exhibited the same level of tensile shear strength as that of similar Mg joint.

• Journal of the Korea Concrete Institute
• /
• v.25 no.2
• /
• pp.217-224
• /
• 2013

Design provisions for the development length of headed bars in ACI 318-08 include concrete compressive strength and yield strength of headed bars as design parameters but do not consider the effects of transvers reinforcement. In addition, they have very strict limitation for clear spacing and material strengths because these provisions were developed based on limited tests. In this study, splice tests using SD600 headed bars with $2d_b$ clear spacing and transverse reinforcement were conducted. Test results show that unconfined specimens failed due to prying action and bottom cover concrete prematurely spalled. The contribution of head bearing on the anchorage strength is only 15% on average implying that unconfined specimens failed before the head bearing was not sufficiently developed. Confined specimens with stirrups placed along whole splice length have enhanced strengths in bearing as well as bond because the stirrups prevented prying action and improved bond capacity. Bond failure occurred in locally confined specimens where stirrups were placed only at the ends of splice length. The stirrups at ends of splice lengths can prevent prying action but the bond capacity did not increase. From regression analysis of test results, an equation to predict anchorage strength of headed bars was developed. The proposed equation consists of bond and bearing contributions and includes transverse reinforcement index. The average ratio of tests to predictions is 1.0 with coefficient of variation of 6%.

• Molecules and Cells
• /
• v.43 no.5
• /
• pp.469-478
• /
• 2020

Hepatitis C virus (HCV) propagation is highly dependent on cellular proteins. To identify the host factors involved in HCV propagation, we previously performed protein microarray assays and identified the LIM and SH3 domain protein 1 (LASP-1) as an HCV NS5A-interacting partner. LASP-1 plays an important role in the regulation of cell proliferation, migration, and protein-protein interactions. Alteration of LASP-1 expression has been implicated in hepatocellular carcinoma. However, the functional involvement of LASP-1 in HCV propagation and HCV-induced pathogenesis has not been elucidated. Here, we first verified the protein interaction of NS5A and LASP-1 by both in vitro pulldown and coimmunoprecipitation assays. We further showed that NS5A and LASP-1 were colocalized in the cytoplasm of HCV infected cells. NS5A interacted with LASP-1 through the proline motif in domain I of NS5A and the tryptophan residue in the SH3 domain of LASP-1. Knockdown of LASP1 increased HCV replication in both HCV-infected cells and HCV subgenomic replicon cells. LASP-1 negatively regulated viral propagation and thereby overexpression of LASP-1 decreased HCV replication. Moreover, HCV propagation was decreased by wild-type LASP-1 but not by an NS5A binding-defective mutant of LASP-1. We further demonstrated that LASP-1 was involved in the replication stage of the HCV life cycle. Importantly, LASP-1 expression levels were increased in persistently infected cells with HCV. These data suggest that HCV modulates LASP-1 via NS5A in order to regulate virion levels and maintain a persistent infection.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.4
• /
• pp.318-325
• /
• 2011

Pitch pine (Pinus rigida Miller) retaining walls using Steel bar, of which the constructability and strength performance are good at the construction site, were manufactured and their strength properties were evaluated. The wooden retaining wall using Steel bar was piled into four stories stretcher and three stories header, which is 770 mm high, 2,890 mm length and 782 mm width. Retaining wall was made by inserting stretchers into Steel bar after making 18 mm diameter of holes at top and bottom stretcher, and then stacking other stretchers and headers which have a slit of 66 mm depth and 18 mm width. The strength properties of retaining walls were investigated by horizontal loading test, and the deformation of structure by image processing (AlCON 3D OPA-PRO system). Joint (Type-A) made with a single long stretcher and two headers, and joint (Type-B) made with two short stretchers connected with half lap joint and two headers were in the retaining wall using Steel bar. The compressive shear strength of joint was tested. Three replicates were used in each test. In horizontal loading test the strength was 1.6 times stronger in wooden retaining wall using Steel bar than in wooden retaining wall using square timber. The timber and joints were not fractured in the test. When testing compressive shear strength, the maximum load of type-A and Type-B was 130.13 kN and 130.6 kN, respectively. Constructability and strength were better in the wooden retaining wall using Steel bar than in wooden retaining wall using square timber.

• Journal of Chest Surgery
• /
• v.23 no.2
• /
• pp.213-221
• /
• 1990

We have experienced 62 cases of modified Fontan operations in Seoul Nat’l University Hospital from Apr. 1986 to Jul. 1989, They were 38 males and 24 females, and their age was ranged from 16 months to 15.5 years of age. [mean age : 5.73$\pm$2.99 years] There were 16 operative deaths and 2 late deaths, therefore 29% of overall mortality. Their diagnoses were as follows; 28 single ventricle, 11 tricuspid atresia, 6 DORV with LV hypoplasia, 3 pulmonary atresia with hypoplastic RV, 3 TGA with hypoplastic RV, 3 cor\ulcornerGA with hypoplastic LV and PA, 6 AV canal defects with PA, and 2 others. Low cardiac output and pleural effusion were developed frequently, so we divide 40 patients into some groups to analyze the physiologic and anatomic causes of them. By the degree of the LCO, group A was no LCO[mean amount of inotropics used: 0-5 \ulcornerg/kg/min] with 17 cases, B mild LCO [5-10] with 11, C moderate to severe LCO but alive[>10] with 8, D severe LCO to death with 4 cases. For the pleural effusion, group 1 was to be removed the chest tube within 1 week with 8 cases, group II within 3 weeks with 21 cases, group III beyond 3 weeks with 12 cases. We considered their age, diagnosis, pulmonary artery size[PA index], pulmonary artery abnormality, palliative shunt, systemic ventricular type, pulmonary artery wedge pressure, as preoperative factors, and operative methods, and as postoperative factors, CVP, LAP, arrhythmia, thrombosis, atrioventricular valvular insufficiency, etc. In the view of LCO, pulmonary artery size and PCWP were statistically significant [P<0.05], and arrhythmia, A-V valve insufficiency were inclined to the group C and D Pleural effusion was influenced by the pulmonary artery size, pulmonary artery resistance, PCWP, and CVP significantly. [P<0.05] And arrhythmia, residual shunt, and A-V valvular insufficiency were inclined to group II and III, too. As a results, the followings are to be reminded as the important factors at the care of post-Fontan LCO, and persistent pleural effusion [1] pulmonary artery size, [2] pulmonary artery resistance, [3] PCWP, [4] CVP, [5] arrhythmia, [6] residual shunt, [7]A-V valvular insufficiency.