• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.6
• /
• pp.720-728
• /
• 2011

Lap joint welding conducts low carbon steel plates using a 2.0kW continuous wave Nd:YAG laser beam. The specimen is composed of thin plate of 20 sheets. Process Variables contain two controlled parameters of the laser power and the welding speed. In order to quantitatively examine the characteristics of the lap welding, the welding quality of the cut section, stain-stress behavior, and the hardness of the welded part are investigated. The weld width difference between the top and the bottom because the welding speed is increased. The reason, cooling rate is decreased because of fast welding speed. When the heat input is higher, larger volume of the base metal will melt and the welding heat has longer time to conduct into the bottom from the top. The microstructure and tensile properties of the joints are investigated in order to analyze the effects of heat input on the quality of laser welded specimen. From the results of the investigation, We observe that welding quality is good for the laser power of 1800W, and laser welding speed from 1.8m/min to 2.2m/min.

• Journal of Microbiology and Biotechnology
• /
• v.28 no.6
• /
• pp.938-945
• /
• 2018

Salinity stress is an important environmental problem that adversely affects crop production by reducing plant growth. The impacts of rhizobacterial strains to alleviate salinity stress on the germination of Lactuca sativa and Raphanus sativus seeds were assessed using different concentrations of NaCl. Plant growth-promoting rhizobacteria (PGPR) strains were also examined to improve the early germination of Chinese cabbage seeds under normal conditions. Lactobacillus sp. and P. putida inoculation showed higher radicle lengths compared with non-inoculated radish (Raphanus sativus) seeds. LAP mix inoculation increased the radicle length of lettuce (Lactuca sativa) seedlings by 2.0 and 0.5 cm at salinity stress of 50 and 100 mM NaCl concentration, respectively. Inoculation by Azotobacter chroococcum significantly increased the plumule and radicle lengths of germinated seeds compared with non-inoculated control. A. chroococcum increased the radicle length relative to the uninoculated seeds by 4.0, 1.0, and 1.5 cm at 50, 100, and 150 mM NaCl concentration, respectively. LAP mix inoculation significantly improved the radicle length in germinated radish seeds by 7.5, 1.3, 1.2, and 0.6 cm under salinity stress of 50, 100, 150, and 200 mM NaCl concentration, respectively. These results of this study showed that PGPR could be helpful to mitigate the salinity stress of different plants at the time of germination.

• Progress in Superconductivity and Cryogenics
• /
• v.25 no.4
• /
• pp.28-31
• /
• 2023

This study presents a comprehensive procedure for the low cycle fatigue test of ultrasonically welded (UW) coated conductor (CC) lap-joints. The entire process is examined in detail, from the robust fabrication of the UW REBCO CC joints to the reliability testing under a low number of repeated cycle fatigue conditions. A continuous I_c measurement system enables real-time monitoring of I_c variations throughout the fatigue tests. The study aims to provide a step-by-step procedure that involves joint fabrication, electromechanical property (EMP) tests under uniaxial tension for stress level determination, and subsequent low-cycle fatigue tests. The joints are fabricated using a hybrid method that combines UW with adding In-Sn soldering, achieving a flux-free hybrid welding approach (UW-HW flux-free). The selected conditions for the low cycle fatigue tests include a stress ratio of R=0.1 and a frequency of 0.02 Hz. The results reveal some insights into the fatigue behavior, irreversible changes, and cumulative damage in the CC joints.

• Journal of the Korea Society of Computer and Information
• /
• v.21 no.3
• /
• pp.57-64
• /
• 2016

This paper deals with the PCB assembly time minimization problem that the PAP (pick-and-placement) machine pickup the K-weighted group of N-components, loading, and place into the PCB placement location. This problem considers the rotational turret velocity according to component weight group and moving velocity of distance in two component placement locations in PCB. This paper suggest heavy-weight component group first pick-and-place strategy that the feeder sequence fit to the placement location Hamiltonean cycle sequence. This algorithm applies the quadratic assignment problem (QAP) that considers feeder sequence and location sequence, and the linear assignment problem (LAP) that considers only feeder sequence. The proposed algorithm shorten the assembly time than iATMA for QAP, and same result as iATMA that shorten the assembly time than ATMA.

• Journal of the Korean Electrochemical Society
• /
• v.1 no.1
• /
• pp.40-44
• /
• 1998

The LAPS device of fast response and high sensitivity, based on electrochemical potential difference, and its system were fabricated for the precise measurement of pH changes and its characteristic were investigated. The electrostatic variation characteristics of LAPS according to the pH changes and parameters in the device were verified through a simulation using LAPS equivalent circuit model. The LAPS device and its system were fabricated on the basis of the result of simulation. The fabricated LAPS system showed linear sensitivity (about 56 mV/pH within the range of pH 2 to pH 11. In order to overcome the defect of general urea sensor (especially slow response time), urease immobilized nitrocellulose membrane was attached on the LAPS and resulted in the very fast response time, 0.29 mV/sec, 0.86 mV/sec at urea concentration of $50{\mu}g/ml,\; 500{\mu}g/ml$, respectively. And also in order to measure the uranyl ion, the uranyl ion selective sensing membrane with calix[6]arene derivative was used and its sensitivity was 25mV/concentration decade in the wide uranyl ion concentration range of $10^{-11}M\;to\;10^{-4}M$.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.14 no.2
• /
• pp.53-62
• /
• 2012

Demand for high resolution weather data grows in the agriculture and forestry fields. Local Analysis and Prediction System (LAPS) can be used to analyze the local weather at high spatial and temporal resolution, utilizing the data from various sources including numerical weather prediction models, wind or temperature profilers, Automated Weather Station (AWS) networks, radars, and satellites. LAPS has been set to analyze weather elements such as air temperature, relative humidity, wind speed, and wind direction every hour at the spatial resolution of $100m{\times}100m$ for Gyeonggi-do on near real-time basis. The AWS data were revised by adding the agricultural field AWS data (33 stations) in addition to the KMA data. The analysis periods were from 1 to 31 August 2009 and from 15 to 21 February 2010. The comparison of the LAPS output showed the smaller errors when using the agricultural AWS observation data together with the KMA data as its input data than using only either the agricultural or KMA AWS data. The accuracy of the current system needs improvement by further optimization of analyzing options of the system. However, the system is highly applicable to various fields in agriculture and forestry because it can provide site specific data with reasonable time intervals.

• Composites Research
• /
• v.29 no.5
• /
• pp.276-281
• /
• 2016

Improvement of the thermal and adhesion properties of stone/wood composites was studied. Tensile test was performed for wood and stone to know the basic mechanical properties. Real-time temperature of stone and wood was measured when stone and wood was heated. To compare thermal transfer properties of stone/wood composites, two types of specimens were tested: one was stone upper whereas another was wood upper. Real time temperature measurement and lap shear test were performed to know thermal and adhesion properties by using CNT-epoxy adhesive in which CNT was dispersed in epoxy adhesive uniformly. The thermal transfer property was better for the wood upper case than stone upper case. Adding CNT improved the heat transfer as well as mechanical properties including lap shear strength.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.5
• /
• pp.129-133
• /
• 2007

Focused Ion Beam(FIB) systems is a useful tool for the fabrication of micro-nano scale structures. In this study, the effects of FIB etching on the Au microstructure are systematically investigated. As the fabrication parameters, ion dose, dwell time and beam overlap ratio are studied. First, the increases of Ga ion dose makes the milling yield higher and the sidewall of milling profile steeper. Dwell time is found to have little effects on the milling profile due to the relatively large milling area of $1\times1{\mu}m^2$ used in this study. However, beam overlap significantly affects not only milling rate but also milling profile. As the beam overlap ratio changes from positive to negative, the development of regular cross-stripe patterns at the bottom with low milling rate is observed.

• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.219-221
• /
• 2006

In an attempt to optimize friction spot joining process of Al alloys for automobiles, Friction spot joining was used make lap feint on strips of AA5052-H32 and AA6022-T4 aluminium alloy. The effects of joining parameters such as tool rotating speed, plunging depth, joining time and kind of upper plate on the joints properties were investigated. An optimal tensile shear strength parameter of a tool rotating speed of 1000rpm, dwell time 2.5sec with upper plate 6022 can be found to make a good joint.

• Journal of the Korea Society of Computer and Information
• /
• v.21 no.4
• /
• pp.81-88
• /
• 2016

The optimal solution of quadratic assignment problem (QAP) cannot get done in polynomial time. This problem is called by NP-complete problem. Therefore the meta-heuristic techniques are applied to this problem to get the approximated solution within polynomial time. This paper proposes an algorithm for a random type QAP, in which the instance of two nodes are arbitrary. The proposed algorithm employs what is coined as a max flow-min distance rule by which the maximum flow node is assigned to the minimum distance node. When applied to the random type QAP, the proposed algorithm has been found to obtain optimal solutions superior to those of the genetic algorithm.