• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.745-750
• /
• 2000

Steel plate bonding technique is most widely used in strengthening of existing concrete structures, but it has inherently a problem of the premature failure such as interface separation and rip off. So far, many studies have been arid out in the manner of laboratory tests for the reinforced concrete beams to find out he mechanism of the premature failure. However, in order to verify the characteristics of the premature failure, more reasonable local investigations are needed rather than such relatively global experimental works. In this study, therefore, the double lap test which simulate the pure shear loadings and the half beam tests which consider combined flexure-shear force have been done. There are, however, difficulties in getting the normal stress caused to premature failure, so that finite element analysis was performed, too. In numerical study, material nonlinearity was considered, and the interface element was applied to model the interface between steel plate and adhesive. From the results of experimental and numerical studies, a realistic failure criterion on the separation of steel plates has been derived.

• 한국정밀공학회지
• /
• 제20권3호
• /
• pp.157-164
• /
• 2003

The pulse-echo method is one of the most widely used ultrasonic techniques for application of nondestructive evaluation. Particularly, quantitative nondestructive evaluation of defects has been considered more important to assure the reliability and the safety of structure. Frequency energy in adhesive joints is based on the ultrasonic wave analysis. The attenuation coefficient upon wave amplitude and the frequency energy that is expressed in the term of wave pressure amplitude were utilized for the primary wave experiment. By means of a control experiment, it was confirmed that the variation of the frequency energy in adhesive joints depends on transition by stress variation. In this paper, the ultrasonic characteristics were measured for single lap joint and Double Cantilever Beam specimen with different fracture modes that was subjected to stress. Consequently, the data that was obtained from the adhesive specimen was analytically compared to the fracture mechanics parameter

• Structural Engineering and Mechanics
• /
• 제72권2호
• /
• pp.155-168
• /
• 2019

This paper presents the results of an experimental investigation on the compressive strength of small scale concentrically axially loaded fiber-reinforced polymer (FRP) confined plain concrete columns, with cylinder concrete strength 19 MPa. For columns with circular (150-mm diameter) and square (150-mm side) cross sections wrapped with glass- and carbon-FRP sheets (GFRP and CFRP, respectively) applied with dry lay-up the effect of different jacket schemes and different overlap configurations on the confined characteristics is investigated. Test results indicate that the most cost effective jacket configuration among those tested is for one layer of CFRP, for both types of sections. In square sections the location of the lap length, either in the corner or along the side, does not seem to affect the confined performance. Furthermore, in circular sections, the presence of an extra wrap with FRP fibers parallel to the column's axis enhances the concrete strength proportionally to the axial rigidity of the FRP jacket. The recorded strains and the distributions of lateral confining pressures are discussed. Existing design equations are used to assess the lateral confining stresses and the confined concrete strength making use of the measured hoop strains.

• 한국초전도ㆍ저온공학회논문지
• /
• 제12권2호
• /
• pp.1-4
• /
• 2010

Normal zone propagation (NZP) within jointed YBCO coated conductors (CC) was analyzed experimentally. The joint between CC tapes were conducted by lap joint method and the characteristics of the jointed CC tapes measured from V-I curve. NZP was induced by thermal heaters attached to two points of the jointed CC tapes; the voltages across the jointed CC tapes were measured and recorded. NZP induced by each heater point is compared in point of protection of CC tapes and magnet. This study about NZP of the jointed tapes may be useful to make a magnet system with several coils using YBCO CC.

• Structural Engineering and Mechanics
• /
• 제72권5호
• /
• pp.557-568
• /
• 2019

Accurate modeling of contact interface in bolted joints is crucial in predicting the dynamic behavior for bolted assemblies under external load. This paper presents a contact pressure distribution based non-uniform virtual material method to describe the joint interface of assembly structure, which is connected by sparsely distributed multi-bolts. Firstly, the contact pressure distribution of bolted joints is obtained by the nonlinear static analysis in the finite element software ANSYS. The contact surface around bolt hole is divided into several sub-layers, and contact pressure in each sub-layer is thought to be evenly. Then, considering multi-asperity contact at the micro perspective, the relationship between contact pressure and interfacial virtual material parameters for each sub-layer is established by using the fractal contact theory. Finally, an experimental platform for the dynamic characteristics testing of a beam lap structure with double-bolted joint is constructed to validate the efficiency of proposed method. It is found that the theoretical results are in good agreement with experimental results by impact response in both time- and frequency-domain, and the relative errors of the first four natural frequencies are less than 1%. Furthermore, the presented model is used to examine the effect of rough contact surface on dynamic characteristics of bolted joint.

• Composites Research
• /
• 제12권1호
• /
• pp.19-27
• /
• 1999

항공기 비행조종장치의 설계와 구조해석을 위해 카본/에폭시 복합재 적층판에 대한 설계개발시험을 수행하였다. 설계개발시험으로 수분흡수시험, 인장, 압축, 베어링, 접합전단시험을 수행하였다. 수분흡수시험을 수행하여 섬유배양에 따른 흡습거동을 관찰하고, 무흡습과 고온·고습하에서의 기계적 특성치를 비교하였다. 인장시험에서는 복합재의 파손에 영향을 미치는 표면 긁힘, 충격 등의 운용손상 요인을 적용하였고, 베어링시험에서는 볼트의 종류와 결합형태를 달리하여 베어링강도를 비교하였다. 설계개발시험을 통해 환경하중배가계수 및 설계허용치를 획득하였으며, 이를 비행조종장치 구조물의 인증시험에 대한 설계변수로 사용하였다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제16권1호
• /
• pp.32-35
• /
• 2014

Recently, many researches on the system of superconducting power supply and superconducting magnetic energy storage (SMES) using high temperature superconducting (HTS) tapes has been progressed. Those kinds of superconducting devices use the heater trigger switches that have a control delay problem at moments of heating up and cooling down. One way to reduce the time delay is using a different HTS tape at trigger part. For example, HTS tape having lower critical temperature can reduce time delay of heating up and heating down stage for heater trigger operation. This paper deals with resistances joint with different kinds of HTS tapes which have different properties to verify usefulness of the suggested method. Three kinds of commercial HTS tapes with different specifications are selected as samples and two kinds of solders are used for comparison. Joint is performed with temperature and pressure controllable joint machine and the joint characteristics are analyzed under the repeatable conditions.

• 한국운동역학회지
• /
• 제28권2호
• /
• pp.93-100
• /
• 2018

Objective: The purpose of this study is to analyze the kinematic characteristics of the national speed skaters in the curve phase of 500-m race. Method: Seven national skaters participated in the study. Race images were acquired using a high - speed camera, and the three-dimensional motion was analyzed. Results: For skaters, whose average velocity in the curve phase is high, the velocity of entry into the straight phase was also fast. The fast skaters showed a larger maximum angle of extension of the knee joints than the relatively slow skaters, and the trunk ROM was smaller. Fast skaters tended to match the timing of the movement of the lower limb with the pelvis, while slow skaters tended to rotate the left pelvis backward. The velocity of the curve phase did not show a clear relationship with stroke time, average trunk angle, and lap time. Conclusion: It is important to skate close to the inner line, keep the trunk ROM below 10 degrees, extend the knee angle to over 160 degrees, and match the movement of the pelvis and lower limb to accelerate in the curve phase. The average velocity of the curves was fast for many athletes, but the competition rankings were low. Therefore, it is possible to improve the performance by optimizing the start technique, the running characteristics of the straight phase, and the physical factors.

• 한국실내디자인학회논문집
• /
• 제26권3호
• /
• pp.45-54
• /
• 2017

A social phenomenon that occurs in a physical space is said to be a complex system. However, space syntax, which is commonly employed by researchers to identify such social phenomena, has various limitations in interpreting their complexity. On the other hand, agent-based modeling considers a variety of factors including the personality of the agent, objective-oriented work flows, estimation according to time flows and better prediction of space use through diverse parameters depending the situation, as well as the characteristics of the space. The agent-based method thus has the potentials to be developed as an alternative to space syntax techniques. In particular, discrete event driven simulation(DEVS), which is part of the agent-based modeling method, embraces the concept of networks just like space syntax, which allows a possible theoretical linkage in the future. This study suggests a procedural model of agent-based DEVS reflecting two different connection methods, i.e. connections between adjacent areas and those of the entire space, and attempts to identify the relationship between the local and regional indices of space syntax. A number of spaces were selected as examples-one for a preliminary experiment and eight modified for the main experiment-and space syntax and DEVS were applied to each of them. The comparative analysis of the results led to the conclusions as follows: 1) Adjacent connections were closely related to local indices, while the whole-space approach to regional indices. Local integration shows both characteristics. 2) Observation of the time flow model indicated a faster convergence with the range of 1 to 3-fold of the total time of one lap, with the error of less than 10%. 3) The heat map analysis showed more obvious characteristics of using the space for the entire space rather than adjacent connections. 4) Space syntax shows higher eligibility than ABM.

• 한국정밀공학회지
• /
• 제33권10호
• /
• pp.821-828
• /
• 2016

Recently, the use of composite materials in the defense system has grown dramatically. The strength/weight and stiffness/weight ratios of composite structures are normally higher than of metals. Woven composites, especially, are increasingly considered for a variety of applications, because they offer good workability for complicated structures. HPW193/RS1222 is one of the most famous woven composites and has been used in many types of Korean military equipment, such as antenna pedestals and radar systems. In this study, we predicted the elastic modulus of HPW193/RS1222 using the principles of unidirectional composite stiffness predictions, such as ROM (Rule of Mixture), HSR (Hart Smith 10% Rule), CLA (Classical Laminate Analysis) and LAP (Laminate Analysis Program). We compared the dynamic characteristics with the experimental predictions and finite-element analysis (FEA). From our results we concluded that transversely isotropic materials are similar to isotropic materials when the shape of the composite structure is complicated.