• 접착 및 계면
• /
• 제7권3호
• /
• pp.16-25
• /
• 2006

내열성 및 투습방수기능을 가진 신발용 직물 및 부직포를 제조하기 위하여 스크린 방식으로 공정조건을 검토하고 투습방수 필름을 라미네이팅 한 후, 최종제품의 물성을 평가하였다. 결과는 다음과 같다. 열가소성 핫 멜트와는 달리 반응형 폴리우레탄 핫 멜트는 작업 이후에 적정한 내열성을 보유하는 것으로 나타났다. 최적의 용융접착 공정조건은 다음과 같다 ; 드럼 온도 $95^{\circ}C$, 호스 온도 $97^{\circ}C$, 공급파이프 온도 $100^{\circ}C$, 스크린 온도 $105^{\circ}C$이고, opposite roller의 압력은 $1kgf/cm^2$, laminating roller의 압력은 $3kgf/cm^2$이며, 가공속도는 15 m/min이다. 투습도는 필름의 두께가 증가함에 따라 투습도는 감소하였으나, 내수도는 증가하였고, 공기투과도는 필름의 영향이 지배적이었다.

• Journal of Astronomy and Space Sciences
• /
• 제2권2호
• /
• pp.153-174
• /
• 1985

The one of critical factor in gas turbine engine performance is high turbine inlet gas temperature. Therefore, the turbine rotor has so many problems which must be considered such as the turbine blade cooling, thermal stress of turbine disk due to severe temperature gradient, turbine rotor tip clearance, under the high operating temperature. The purpose of this study is to provider the temperature distribution and heat flux in turbine disk which is required to considered premensioned problem by the Finite Difference Method and the Finite Element Methods on the steady state condition. In this study, the optimum aspect ratio of turbine disk was analysed for various heat conductivity of turbine disk material by Finite Difference Method, and the effect of laminating method with high conductivity materials to disk thickness direction by Finite Element Methods in order to cool the disk. The laminating method with high conductivity material on the side of the disk is effective.

• 한국전기전자재료학회논문지
• /
• 제28권1호
• /
• pp.7-11
• /
• 2015

In this study, $Si_3N_4$/SnZnO/AZO/Ag/Ti/ITO multi-layer film were prepared on glass substrate by DC/RF magnetron sputtering method. To prevent interfacial reaction between Ag and ITO layer, Ti buffer layer was inserted. Optical properties and sheet resistance were studied depending on laminating times of each multi-layered film especially in visible ray. The simulation program, EMP (essential macleod program), was adopted and compared with experimental data to expect the experimental result. It was found out that the transmittance of the first stacked $Si_3N_4$/SnZnO/AZO/Ag/Ti/ITO multi-layer film was more than 90%. However, with increasing stacking times, the optical properties of $Si_3N_4$/SnZnO/AZO/Ag/Ti/ITO multi-layer film get worse. Consequently, Ti layer is good for oxidation barrier, but too many uses of this layer may have an adverse effect to optical properties of TCO film.

• 폴리머
• /
• 제36권2호
• /
• pp.119-123
• /
• 2012

금속 박막 접착제로 사용되는 용제형 폴리우레탄 접착제의 라미네이팅 조건에 따른 접착 메커니즘과 이에 따른 접착력 변화를 살펴보았다. 강판에 도포된 접착제의 열처리 온도와 시간에 따라 폴리우레탄 접착제의 blocking agent로 사용된 옥심이 분해되어 이소시아네이트기가 발현되고 이들이 강판과 알루미늄 포일의 하이드록실기와 반응하여 강판 접착이 이루어짐을 알 수 있었다. 접착 강도는 접착 온도 및 시간에 따라 발생된 이소시아네이트 함량과 밀접한 관계가 있음을 확인하였다. 하지만 지나친 접착 온도 및 접착 시간의 증가는 접착제에 함유된 용매의 감소와 접착제 분해를 유발시켜 접착 강도를 감소시킴을 알 수 있었다.

• 한국염색가공학회지
• /
• 제34권3호
• /
• pp.173-184
• /
• 2022

In this study, the TPU film was laminated on an aramid fabric or circular knits in order to implement an air cushion material that can respond to high impact forces in case of a fall and is easy to expand. To increase the bonding strength between the fabric layer and the film layer, a primer layer was formed in two ways: one for thermally bonding and laminating PET film and two for coating and aging hot melt type PUR adhesive. The tensile strength of the aramid air cushion was 2.5 times higher than that of the circular knits, but the tensile elongation of the aramid air cushion was very low compared to that of the circular knits. The tear strength of the aramid air cushion was about twice or more superior to that of the circular knits, the primer treatment method was good at A, and the peel strength was excellent at method A. The aramid air cushion was the lightest in weight. Summarizing the above results, it was best to combine the air cushion material with aramid woven fabric and primer treatment method A to cope with the high impact force applied when falling.

• 한국염색가공학회:학술대회논문집
• /
• 한국염색가공학회 2006년도 임시총회 및 추계학술발표회
• /
• pp.219-221
• /
• 2006

• Journal of the Korean Wood Science and Technology
• /
• 제46권3호
• /
• pp.213-220
• /
• 2018

리기다소나무를 구조용 집성재의 재료로 이용하기 위해 판면의 옹이와 대패가공 후 방치시간에 따른 수지 삼출량이 레조르시놀수지로 접착한 판재의 접착성능에 미치는 영향을 검토하였다. 고온($120{\sim}95^{\circ}C$) 및 저온($65{\sim}50^{\circ}C$)에서 건조한 리기다소나무의 수지 삼출량은 판목면이 정목면 보다 저온건조재가 고온건조재보다 많았다. 방치시간별로는 저온건조재는 3일째 고온건조재는 7일째에 최고함량을 보였고, 이후부터는 서서히 감소하여 15~90일에는 거의 차이가 없었다. 접착성능은 수지의 삼출이 많은 2~3일까지는 낮았으나 15일 이후에는 큰 차이가 없었으며, 고온 및 저온 건조재 모두 방치시간에 관계없이 KS 기준의 접착성능을 만족하였다. 옹이부가 포함된 적층 구성에서의 접착강도는 KS의 접착강도 기준 이상이었으나 목파율은 기준인 65% 이상을 만족하지 못하였다. 적층 단면구성(정목+정목, 판목+판목, 정목+판목)에 따른 접착성능은 고온 및 저온건조재 모두 모든 적층구성에서 KS의 기준을 크게 상회하였다.

• Steel and Composite Structures
• /
• 제17권6호
• /
• pp.825-834
• /
• 2014

This manuscript presents an experimental investigation on the effect of Multi-walled carbon nanotubes (MWCNTs) addition on the tensile, flexural and impact properties of woven Kevlar fabric reinforced epoxy composites. MWCNTs were dispersed in the epoxy resin by sonication technique and the samples were fabricated by hand layup laminating procedure. Scanning electron microscopy (SEM) was used to characterize the microstructure of produced samples. The effects of adding small amounts (${\leq}1%$) of MWCNT on the tensile, flexural and impact (Izod) behaviors of laminated composites were analyzed. Results revealed that MWCNTs enhanced the Young's modulus up to 20%, bending modulus up to 40%, and impact strength up to 45% in comparison with woven Kevlar fabric/epoxy composites. It was found that the maximum improvements in mechanical properties were happened for 0.5 wt.% MWCNT.

• 대한기계학회논문집A
• /
• 제29권10호
• /
• pp.1289-1297
• /
• 2005

The flow in a microchannel is usually characterized as a low Reynolds number (Re) so that good mixing is quite difficult to be achieved. In this regard, we developed a novel chaotic micromixer, named Serpentine Laminating Micromixer (SLM) in the present study, Part 1. In the SLM, the higher level of chaotic mixing can be achieved by combining two general chaotic mixing mechanisms: splitting/recombination and chaotic advection. The splitting and recombination (in other term, lamination) mechanism is obtained by the successive arrangement of 'F'-shape mixing units in two layers. The chaotic advection is induced by the overall three-dimensional serpentine path of the microchannel. Chaotic mixing performance of the SLM was fully characterized numerically. To compare the mixing performance, a T-type micromixer which has the same width, height and length of the SLM was also designed. The three-dimensional numerical mixing simulations show the superiority of the SLM over the T-type micromixer. From the cross-sectional simulation results of mixing patterns, the chaotic advection effect from the serpentine channel path design acts favorably to realize the ideal lamination of fluid flow as Re increases. Chaotic mixing mechanism, proposed in this study, could be easily integrated in Micro-Total-Analysis-System, Lab-on-a-Chip and so on.

• Journal of the Korean Wood Science and Technology
• /
• 제51권4호
• /
• pp.239-252
• /
• 2023

In this study, bending and compression strength tests were performed to investigate effect of composition of layer layout of Larix cross-laminated timber (CLT) on mechanical properties. The Larix CLT consists of five laminae, and specimens were classified into four types according to grade and composition of layer. The layer's layout were composited as follows 1) cross-laminating layers in major and minor direction (Type A), and 2) cross-laminating external layer in major direction and internal layer applied grade of layer in minor direction (Type B). E12 and E16 were used as grades of lamina for major direction layer of Type A and external layer of Type B according to KS F 3020. In results of the bending test of CLT using same grade layer according to layer composition, the modulus of elasticity (MOE) of Type B was higher than Type A. In case of prediction of bending MOE of Larix CLT, the experimental MOE was higher than 1.00 to 1.09 times for Shear analogy method and 1.14 to 1.25 times for Gamma method. Therefore, it is recommended to predict the bending MOE for Larix CLT by shear analogy method. Compression strength of CLT in accordance with layer composition was measured to be 2% and 9% higher for Type A using E12 and E16 layers than Type B, respectively. In failure mode of Type A, progress direction of failure generated under compression load was confirmed to transfer from major layer to minor layer by rolling shear or bonding line failure due to the middle lamina in major direction.