• 한국농촌건축학회논문집
• /
• 제24권2호
• /
• pp.45-52
• /
• 2022

Of the 17,106 domestic reservoirs(as of December 2020), 14,611 are older than 50 years, and these old reservoirs will gradually increase over time. The injection grouting method is most applied to the reinforcement method of the aging reservoir. However, the injection grouting method is not accurate in uniformity and reinforced area. An laboratory model test was conducted to evaluate the applicability of the deep mixing method, which compensated for these shortcomings, as a reservoir reinforcement method. As a result of calculating the hydraulic conductiveity for each method through the model test results, the injection grouting method was calculated as a hydraulic conductiveity value that was about 7.5 times larger than that of the deep mixing method. As a result of measuring the water level change in the laboratory model test, it was found that the water level change decreased in the injection method and deep mixing method compared to the non-reinforcement method. In addition, deep mixing method showed a water level change of about 15% based on 40 hours compared to the injection method, indicating that the water-reducing effect was superior to that of the injection method.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.412-419
• /
• 2009

Large quantity of extra soils discharged from excavation site in Songdo area can be treated by hardening agents and utilized in surface stabilized layer overlying thick reclaimed soft soil deposit. Though surface layer stabilization method using cement or lime for very soft soils has been studied in recent years, but studies on moderately soft clayey silt has not been tried. The purpose of this research is to investigate optimum mixing condition for stabilizing Songdo marine soil with low plasiticity. The optimum mixing conditions of hardening agents with Songdo soil such as kind of agents, mixing ratio, initial water content and curing time are investigated by uniaxial compression test and laboratory vane test. The results indicate that strength increases with high mixing ratio and long curing time, while decreases drastically under certain water content before mixing. Finally, optimum mixing condition considering economic efficiency and workability with test results was proposed.

• Computers and Concrete
• /
• 제13권6호
• /
• pp.781-798
• /
• 2014

Estimating the workability of self-compacting concrete (SCC) is very important both in laboratories and on construction site. A method using visual information during the mixing process was proposed in this paper to estimate the workability of SCC. First, fourteen specimens of concrete were produced by a single-shaft mixer. A digital camera was used to record all the mixing processes. Second, employing the digital image processing, the visual information from mixing process images was extracted. The concrete pushed by the rotating blades forms two boundaries in the images. The shape of the upper boundary and the vertical distance between the upper and lower boundaries were used as two visual features. Thirdly, slump flow test and V-funnel test were carried out to estimate the workability of each SCC. Finally, the vertical distance between the upper and lower boundaries andthe shape of the upper boundary were used as indicators to estimate the workability of SCC. The vertical distance between the upper and lower boundaries was related to the slump flow, the shape of the upper boundary was related to the V-funnel flow time. Based on these relationships, the workability of SCC could be estimated using the mixing process images. This estimating method was verified by three more experiments. The experimental results indicate that the proposed method could be used to automatically estimate SCC workability.

• Computers and Concrete
• /
• 제25권5호
• /
• pp.433-445
• /
• 2020

A method is proposed in this paper to estimate the workability of self-compacting concrete (SCC) in different mixing conditions with different mixers and mixing volumes by recording the mixing process based on deep learning (DL). The SCC mixing videos were transformed into a series of image sequences to fit the DL model to predict the SF and VF values of SCC, with four groups in total and approximately thirty thousand image sequence samples. The workability of three groups SCC whose mixing conditions were learned by the DL model, was estimated. One additionally collected group of the SCC whose mixing condition was not learned, was also predicted. The results indicate that whether the SCC mixing condition is included in the training set and learned by the model, the trained model can estimate SCC with different workability effectively at the same time. Our goal to estimate SCC workability in different mixing conditions is achieved.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.861-863
• /
• 2003

The method of measurement for laboratory tests on noise emission from appliances and equipment used in water supply installations is specified in ISO 3822-1. This part of standard gives detailed descriptions for mounting and operating draw-off taps and mixing valves in such laboratory test. Draw-off taps and mixing valves are the most common kind of appliance used in water supply installations.

• 한국지반환경공학회 논문집
• /
• 제25권6호
• /
• pp.5-12
• /
• 2024

현재 저수지 제체의 차수성 및 안전성 확보를 위해 약액을 저압으로 주입하여 제체 손상을 최소화하는 그라우팅 공법이 보편적으로 사용되고 있으나, 내구성 확보와 체계적인 고화재의 배합비 결정방법이 정립되어 있지 않은 문제들이 있다. 본 연구에서는 원지반과 고화재를 다양한 중량비율로 교반·혼합하였을 경우 혼합체의 투수계수와 강도를 실내시험을 통해 확인하였으며, 시험결과들의 분석을 통해 최적 배합비를 제안하였다. 실내실험을 위한 공시체는 고화재의 배합량을 고려하여 제작하였다. 투수시험용 공시체는 사질토와 점성토 별 고화재 배합량 1.5kN/m³에 대해 제작하였으며, 투수시험 결과 차수 성능이 확보되어 각종 설계기준을 만족하는 것을 확인하였다. 강도시험을 위한 공시체는 점성토의 경우 5가지, 사질토는 3가지 배합비로 각각 3개 총 24개의 시편을 제작하였으며, 시험 결과 사질토와 점성토 모두 배합량 2.0kN/m³ 이하에서는 일축압축강도가 재령일이 증가함에 따라 선형적으로 증가하는 경향을 나타냈다. 따라서 현장에 적용되는 최적의 배합비는 고화재 배합량을 1.5kN/m³ 및 2.0kN/m³으로 결정하였다. 또한 현재 운영 중인 노후 저수지 개보수사업 설계사례를 대상으로 실험성과를 반영한 수치해석을 실시한 결과 저수지 제체의 차수 및 안전성 증대 효과를 확인하였다.

• 한국지반신소재학회논문집
• /
• 제15권2호
• /
• pp.35-44
• /
• 2016

PET 인공골재의 배수특성 평가를 위하여 실내 수평투수실험, 실대형 수평투수실험을 실시하였다. 실내 수평투수실험은 PET 골재의 생산량에 따라 세 종류의 입도별로 분류하고, 분류된 PET 골재를 정해진 배합비에 의해 20가지로 분류하여 단계별 하중을 재하하면서 실시하였다. 또한 실내 수평투수실험에 의해 분석된 결과를 활용하여 재하하중에 따른 투수계수의 변화경향이 가장 적은 실험 유형의 배합비로 실대형 수평투수실험을 실시하였고, 실내 수평투수실험 결과와 비교하여 신뢰도를 평가하였다.

• 한국지반신소재학회논문집
• /
• 제15권2호
• /
• pp.1-12
• /
• 2016

본 연구에서는 기존의 심층혼합처리공법용 안정재의 문제점을 해결하기 위해 탈황분진을 이용하여 개발한 친환경 지반안정재(CMD-SOIL)의 적용성을 평가하기 위해 실내배합시험 및 현장시험시공을 실시하였다. 실내배합시험 결과 함수비, 투입비 및 W/B 변화에 따른 CMD-SOIL의 일축압축강도가 기존의 고로슬래그 시멘트와 비교하여 최대 1.136배 큰 것으로 나타났고, 패각이 함유된 흙 재료에서는 최대 1.222배, 부상토가 혼합된 시료에서는 최대 1.363배 큰 것으로 나타났다. 또한 현장시험시공 결과, 실내배합강도와 현장강도의 비(${\lambda}$)가 0.77로 나타나 기존의 연구결과(${\lambda}=2/3$)와 유사한 경향을 보이고 있어 기존의 안정재와 비교하여 동등 이상의 성능을 발휘할 수 있을 것으로 판단된다.

• 한국지반환경공학회 논문집
• /
• 제23권5호
• /
• pp.15-24
• /
• 2022

준설 매립지반의 경우 공학적, 물리적 조건이 열악하여 매립현장에서 이를 개량하기 위한 시간과 비용이 많이 든다. 또한 국내 실정에 적합한 관중혼합 이송처리 공법의 적용사례가 없고 공법 적용성 및 효과에 관하여 불확실할 뿐 아니라 실제 현장과 실내실험 간의 차이가 발생할 수 있다. 이러한 문제점을 해결하기 위해 개질재(표준사+입도조절재)가 혼합된 준설토를 대상으로 실내 특성실험을 통해 개질재의 적정한 입도분포 및 함수비 범위를 결정하였다. 그 결과 단계투기 시 침강압밀계수가 증가하고 분리침강에 대한 개선효과가 있는 것으로 확인되었다. 실험결과 회귀분석을 통해 개질 처리토의 함수비에 따른 비배수전단강도를 도출하고, 이를 활용하여 배합비를 결정할 수 있는 상관식을 제시하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.793-808
• /
• 2009

This paper presents procedure and prediction method of internal and external stabilities when designing D.C.M, with main factors to be considered, such as chemical reaction of additive, physical properties of stabilized body and mixing strength. Results show that through case studies, a design unconfined compressive strength of stabilized body (hereafter referred to as 'compressive strength') directly depends on the quantity of cement, which is decided by laboratory test, and the compressive strength enormously affects internal and external stabilities. So laboratory mixing test to obtain the compressive strength for design allowable stress should be given careful considerations.