• Tunnel and Underground Space
• /
• v.25 no.3
• /
• pp.231-243
• /
• 2015

In this study, both in-situ stress measurements and a lot of laboratory rock tests were conducted at a metal mine in Jeongseon, Korea. The stress ratio obtained from in-situ stress measurements showed a tendency to decrease according to depth below surface and its average value was 1.10. The mechanical properties such as unit weight, absorption ratio, porosity, elastic wave velocity, uniaxial compressive strength, Young's modulus, Poisson's ratio, tensile strength, shore hardness, friction angle and cohesion were investigated for the four different rocks mainly distributed at a studied mine, which were dolomite, felsite, granite and magnetite. The mechanical properties of the four different rocks were compared by means of statistical analyses, whereupon the felsite and the granite turned out to have more strength characteristics than the magnetite. The correlation of mechanical properties was also investigated, whereupon a few results against the general correlation were found out. The failure criteria of the four different rocks were finally discussed by means of both Mohr-Coulomb criterion and Hoek-Brown criterion.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.10 no.5
• /
• pp.76-86
• /
• 2007

For the purpose of ground improvement by means of soil flushing systems. Incorporated technique with prefabricated vertical drains have been used for dewatering from fine-grained soils. The laboratory model tests were performed by using the flushing tracer solutions for silty soils and recorded the tracer concentration changes with the elapsed time and flow rates. A mathematical model for prediction of contaminant transport using the PVD technology has been developed. The clean-up times for the predictions on both soil condition indicate more of a sensitivity to the dispersivity parameter than to the extracted flow rate and vertical velocity parameters. Based on the results of the analyses, numerical analysis indicate that the most important factor to the in-situ soil remediation in prefabricated vertical drain system is the effective diameter of contaminated soil.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.2
• /
• pp.71-83
• /
• 2007

Liquefaction resistance depends strongly upon the degree of saturation, which is expressed in terms of the pore pressure coefficient, B. The B-value has been widely used to quantify the state of saturation of laboratory samples. However, it is practically impossible to determine in situ state of saturation by using the B-value. So, P-wave velocity can be alternatively used as a convenient index for evaluating the in situ state of saturation. In this paper, the Stokoe type torsional shear (TS) testing system was modified to saturate the specimen, with which it is also possible to measure P ($V_p$), S-wave velocity ($V_s$) and the excess pore water pressure buildup In order to examine the effect of B-value for nearly saturated sands. A series of the tests were carried out at 3 relative densities (40%, 50% and 75%) and various B-values using Toyoura sand. Based on the test results, the variations of $V_p\;and\;V_s$ with B-value were analyzed and compared with a existing theoretically derived formula. The normalized pore water pressure, $du/{\sigma}{_0}'$ and cyclic threshold shear strain, ${\gamma}^c_{th}$ with B-value were also analyzed. Additionally the test results related to pore water pressure were analyzed by $V_p$ to apply to the field seismic analysis.

• Korean Journal of Optics and Photonics
• /
• v.17 no.4
• /
• pp.347-353
• /
• 2006

The electro-wetting effect can be implemented as a fast means to move liquid interfaces. A continuous and numerical method would be required in measurement of electro-wetting liquid interfaces. We propose an /in-situ/ measurement method to characterize the dynamic change in curvature of liquid interfaces. In the proposed method, variation of light intensity transmitted through the liquid interfaces is measured, leading to numerical determination of the liquid curvatures. Experimental results obtained from our efficient method are confirmed by the direct images of a streak camera.

• Ocean and Polar Research
• /
• v.35 no.3
• /
• pp.193-203
• /
• 2013

A GPS-drifter was newly designed to observe the sea surface skin current and to estimate the direct wind effect on the sea surface. After conducting a test to establish and verify the accuracy of the GPS itself in the laboratory, in-situ experimental campaigns at Saemangeum in Gunsan city and Haeundae in Busan city, Korea, were carried out to ascertain the drifter track and to estimate the velocity data set on Oct. 3, 15, 23, 27 and Nov. 25, 2011. The current meters, RCM9 and ADCP, were moored together to remove the background current field, and the wind data were obtained from several marine stations such as towers and buoys in these areas. The drifter-observed velocity show good agreement with the flow obtained by the HF radar in the Saemangeum area. The direction of the wind-driven current extracted from the drifter-observed velocity was completely deflected to the right, however the degree of the angle was different according to the drift types. The average speed of the wind-driven current matched with 2.19~2.81% of the wind speed and the deflection angle was about $8.0{\sim}10.9^{\circ}$ without adjustment for the land-sea effect, and about 2.19~2.84% and $4.1{\sim}6.0^{\circ}$ with the adjustment for the land-sea effect.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.1
• /
• pp.41-52
• /
• 1999

In order to assess the quality and depth of ground densification by compaction, SPT and/or CPT are performed before and after compaction. Both methods are intrusive and one point tests, require a substantial time to evaluate a large area, and their results are quite dependent on the operation technique and soil type. In this paper, the quality and extent of ground densification by compaction was evaluated by using in situ SASW test and laboratory resonant column (RC) test results. SASW test was used to determine the shear wave velocity profiles before and after compaction, and RC test was adopted to determine the correlation between the normalized shear wave velocity and the density of the site, which is almost uniquely independent of confinement. Testing and data reduction procedures of both tests were discussed, and a simplified evaluation procedure of ground densification was proposed. Finally, the feasibility of the proposed method was verified by performing field study at Inchon International Airport Project. Field densities determined by the proposed method matched well with those determined by sand cone tests.

• Geophysics and Geophysical Exploration
• /
• v.11 no.1
• /
• pp.41-51
• /
• 2008

To construct in situ velocity-porosity relationships for oceanic basalt, considering crack features, P- and S-wave velocity measurements on basaltic samples obtained from the eastern flank of the Juan de Fuca Ridge were carried out under confining pressures up to 40 MPa. Assuming that the changes in velocities with confining pressures are originated by micro-crack closure, we estimated micro-crack aspect ratio spectra using the Kuster-$Toks{\ddot{o}}z$ theory. The result demonstrates that the normalised aspect ratio spectra of the different samples have similar characteristics. From the normalised aspect ratio spectrum, we then constructed theoretical velocity-porosity relationships by calculating an aspect ratio spectrum for each porosity. In addition, by considering micro-crack closure due to confining pressure, a velocity-porosity relationship as a function of confining pressure could be obtained. The theoretical relationships that take into account the aspect ratio spectra are consistent with the observed relationships for over 100 discrete samples measured at atmospheric pressure, and the commonly observed pressure dependent relationships for a wide porosity range. The agreement between the laboratory-derived data and theoretically estimated values demonstrates that the velocity-porosity relationships of the basaltic samples obtained from the eastern flank of the Juan de Fuca Ridge, and their pressure dependence, can be described by the crack features (i.e. normalised aspect ratio spectra) and crack closure.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.5
• /
• pp.215-223
• /
• 2005

Piezo-ceramics are special materials which transform energy from mechanical to electrical forms and vice versa. Bender elements are composite materials consisting of thin piezo-ceramics and elastic shims, and are widely used as actuators and transducers in the field of electronics, robotics, autos and mechatronics utilizing the effectiveness of energy transformation capability. In geotechnical engineering, commercial bender elements are used in laboratory as source and receiver in the measurements of soil stiffness. The elements were built by using various metal shims sandwiched between piezo-ceramics and coating over the composite in the research. A pair of elements were buried in a concrete block and used as source and receiver to measure the stiffness of the concrete. The test results were verified by comparing with the resonant column testing results. In a preliminary stage of the development of an in-situ seismic testing equipment using bender elements for soft clay materials, shear waves were generated and measured by burying the elements in the barrel of kaolinite and water mixture. The measured shear wave signals were so distinct for the first-arrival pick that applicability of the elements in the field measurements could be very promising.

• Journal of Ocean Engineering and Technology
• /
• v.22 no.4
• /
• pp.20-26
• /
• 2008

The primary purpose of this study was to quantitatively examine whether there was a difference in the settling velocities of cohesive sediments in the Saemankeum artificial lake before and after the closure of the Saemankeum seadike. Through in situ sediment sampling and laboratory experiments, the settling velocities were estimated as a function of the suspension concentration and their physico-chemical properties, such as grain size distribution, the percentage of organic contents, mineralogical composition, etc. were also examined. In this study, their inter-relation with settling velocities were also analyzed qualitatively. The result of the settling tests for Saemankeum sediments showed that there was a big difference in the settling velocities before and after the closure of the Saemankeum seadike. Its settling velocities in a flocculated settling region became remarkably larger after the closure compared to those before the closure, while they were similar but relatively smaller in a hindered settling region. This was found to be mainly due to the difference in their grain size.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.02a
• /
• pp.93-112
• /
• 2000

The permeability of converter slag, replacing material of sand mat on improving soft clay foundation, was evaluated in the laboratory. The effects of grain size, flow water time and aging were investigated using sea and fresh water. Converter slag being submerged with fresh water, the coefficients of permeability in A and B samples less than 10mm grain sizes were measured as 6.52${\times}$10$\^$-2/cm/sec and 5.99${\times}$10$\^$-1/cm/sec, while changed as 1.88${\times}$10$\^$-2/cm/sec, 3.86${\times}$10$\^$-1/cm/sec under sea water condition. Also, the condition of turbulent flow may exit and was experimentally identified from the relationship between hydraulic gradient and seepage velocity. After 180 days on using sea water, the coefficients of permeability of sample A and B samples decreased ten times smaller than those initial values. And after that time continually decreased as for till 360 days. The reduction of permeability coefficient was considered to influence filled with voids in high-calcium quicklime(CaO). However, in-situ coefficient of permeability was practically satisfactory.