• Korean Journal of Remote Sensing
• /
• v.32 no.1
• /
• pp.67-71
• /
• 2016

The surface reflectance is essential to retrieval various indicators related land properties such as vegetation index, albedo and etc. In this study, we estimated surface reflectance using Himawari-8 / Advanced Himawari Imager (AHI) channel data. In order to estimate surface reflectance from Top of Atmosphere (TOA) reflectance, the atmospheric correction is necessary because all of the TOA reflectance from optical sensor is affected by gas molecules and aerosol in the atmosphere. We used Second Simulation of a Satellite Signal in the Solar Spectrum Vector (6SV) Radiative Transfer Model (RTM) to correct atmospheric effect, and Look-Up Table (LUT) to shorten the calculation time. We verified through comparison Himawri-8 / AHI surface reflectance and Proba-V S1 products. As a result, bias and Root Mean Square Error (RMSE) are calculated about -0.02 and 0.05.

• Korean Journal of Remote Sensing
• /
• v.22 no.5
• /
• pp.379-383
• /
• 2006

Satellite imagery may contain large regions covered with atmospheric aerosol. A highresolution satellite imagery affected by non-homogenous aerosol cover should be processed for land cover study and perform the radiometric calibration that will allow its future application for Korea Multi-Purpose Satellite (KOMPSAT) data. In this study, aerosol signal was separated from high resolution satellite data based on the reflectance separation method. Since aerosol removal has a good sensitivity over bright surface such as man-made targets, aerosol optical thickness (AOT) retrieval algorithm could be used. AOT retrieval using Look-up table (LUT) approach for utilizing the transformed image to radiometrically compensate visible band imagery is processed and tested in the correction of satellite scenery. Moderate Resolution Imaging Spectroradiometer (MODIS), EO-l/HYPERION data have been used for aerosol correction and AOT retrieval with different spatial resolution. Results show that an application of the aerosol detection for HYPERION data yields successive aerosol separation from imagery and AOT maps are consistent with MODIS AOT map.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2012.11a
• /
• pp.668-671
• /
• 2012

본 논문에서는 차세대 비디오 압축 표준인 HEVC(High Efficiency Video Coding) 복호기의 연산량과 하드웨어 면적을 감소시키기 위하여 화면내 예측 하드웨어 구조를 제안한다. 제안하는 하드웨어 구조는 공통 수식에 대한 연산을 공유하는 공유 연산기를 사용하여 연산량 및 연산기 개수를 감소시키고, $4{\times}4$ PU와 $64{\times}64$ PU의 필터링 수행 여부에 대한 연산을 수행하지 않고 나머지 PU에 대해서는 LUT를 이용하여 연산을 수행하기 때문에 연산량 및 연산 시간을 감소시킨다. 또한 하나의 공통 연산기만을 사용하여 예측 픽셀을 생성하기 때문에 하드웨어 면적이 감소한다. 제안하는 구조를 TSMC 0.18um 공정을 이용하여 합성한 결과 최대 동작 주파수는 100MHz이고, 게이트 수는 140,697이다. $4{\times}4$ PU를 기준으로 제안하는 구조의 처리 사이클 수는 11 사이클로 기존 구조 대비 54% 감소하였고, 16개 참조 픽셀의 필터링 처리를 기준으로 제안하는 구조의 덧셈 연산기 개수는 37개로 표준 draft 6에 비해 22.9% 감소하였다.

• Journal of Semiconductor Engineering
• /
• v.2 no.2
• /
• pp.130-135
• /
• 2021

Recently, deep neural networks (DNNs) are actively used for action control so that an autonomous system, such as the robot, can perform human-like behaviors and operations. Unlike recognition tasks, the real-time operation is essential in action control, and it is too slow to use remote learning on a server communicating through a network. New learning techniques, such as reinforcement learning (RL), are needed to determine and select the correct robot behavior locally. In this paper, we propose an energy-efficient DNN processor with a LUT-based processing engine and near-zero skipper. A CNN-based facial emotion recognition and an RNN-based emotional dialogue generation model is integrated for natural HRI system and tested with the proposed processor. It supports 1b to 16b variable weight bit precision with and 57.6% and 28.5% lower energy consumption than conventional MAC arithmetic units for 1b and 16b weight precision. Also, the near-zero skipper reduces 36% of MAC operation and consumes 28% lower energy consumption for facial emotion recognition tasks. Implemented in 65nm CMOS process, the proposed processor occupies 1784×1784 um2 areas and dissipates 0.28 mW and 34.4 mW at 1fps and 30fps facial emotion recognition tasks.

• Journal of Advanced Information Technology and Convergence
• /
• v.10 no.2
• /
• pp.153-166
• /
• 2020

DDI(Display Driver IC) are used to drive numerous pixels that make up display. For stable driving of DDI, it is necessary to attach a protective film to shield electromagnetic waves. When the protective film is attached, defects often occur if the film is inclined or the center point is not aligned. In order to minimize such defects, an algorithm for correcting the center point and the inclined angle using camera image information is required. This technology detects the corner coordinates of the protective film by image processing in order to correct the positional defects where the protective film is attached. Corner point coordinates are detected using an algorithm, and center point position finds and correction values are calculated using the detected coordinates. LUT (Lookup Table) is used to quickly find out whether the angle is inclined or not. These algorithms were described by Verilog HDL. The method using the existing software requires a memory to store the entire image after processing one image. Since the method proposed in this paper is a method of scanning by adding a line buffer in one scan, it is possible to scan even if only a part of the image is saved after processing one image. Compared to those written in software language, the execution time is shortened, the speed is very fast, and the error is relatively small.

• Journal of the Korean Society of Systems Engineering
• /
• v.17 no.2
• /
• pp.49-60
• /
• 2021

The Core Protection Calculator System (CPCS) is vital for plant safety as it ensures the required Specified Acceptance Fuel Design Limit (SAFDL) are not exceeded. The CPCS generates trip signals when Departure from Nucleate Boiling Ratio (DNBR) and Local Power Density (LPD) exceeds their predetermined setpoints. These setpoints are established based on the operating margin from the analysis that produces the SAFDL values. The goal of this research is to create a simplified CPCS that optimizes operating margin for I-SMRs. Because the I-SMR is compact in design, instrumentation placement is a challenge, as it is with Ex-core detectors and RCP instrumentation. The proposed CPCS addresses the issue of power flux measurement with In-Core Instrumentation (ICI), while flow measurement is handled with differential pressure transmitters between Steam Generators (SG). Simplification of CPCS is based on a Look-Up-Table (LUT) for determining the CEA groups' position. However, simplification brings approximations that result in a loss of operational margin, which necessitates compensation. Appropriate compensation is performed based on the result of analysis. FPGAs (Field Programmable Gate Arrays) are presented as a way to compensate for the inadequacies of current systems by providing faster execution speeds and a lower Common Cause Failure rate (CCF).

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38B no.2
• /
• pp.140-145
• /
• 2013

This paper proposes the high speed LDPC decoder structure base on the DVB-S2. Firstly, We study the solution to avoid the memory conflict. For the high speed decoding process the decoder adapts the HSS(Horizontal Shuffle Scheduling) scheme. Secondly, for the high speed decoding algorithm normalized Min-Sum algorithm is adapted instead of Sum-Product algorithm. And the self corrected is a variant of the LDPC decoding that sets the reliability of a Mc${\rightarrow}$v message to 0 if there is an inconsistency between the signs of the current incoming messages Mv'${\rightarrow}$c and the sign of the previous incoming messages Moldv'${\rightarrow}$c This self-corrected algorithm avoids the propagation on unreliable information in the Tanner graph and thus, helps the convergence of the decoder.Start after striking space key 2 times. Lastly, and this paper propose the optimal hardware architecture supporting the high speed throughput.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38C no.10
• /
• pp.928-936
• /
• 2013

3D crosstalk is one of the disturbing things to recognize 3D images. This is caused by the phenomenon that input image for left eye is transferred at the right eye and right eye is transferred at the left eye because of the imperfect isolation by the device characteristics. In this paper, we review the 3D PDP (Plasma Display Panel) operation using active shutter glasses and crosstalk measurement method and investigate the major cause of 3D crosstalk and extend conventional 3D crosstalk using full white and full black image input to Gray-to-Gray (GtoG) 3D crosstalk. We suggest a specific method to reduce Gray-to-Gray 3D crosstalk by using Look up Table (LUT) and sub-field mapping in PDP. And then, we verify the method by measuring GtoG 3D crosstalk rate through specific test images and numerical results.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.10 no.4
• /
• pp.189-198
• /
• 2015

Most IoT-related approaches have tried to establish the relation by connecting the network between things. The proposed research will present how the pervasive interaction of eco-system formed by touching the objects between humans and things can be recognized on purpose. By collecting and sharing the detected patterns among all kinds of things, we can construct the environment which enables individualized interactions of different objects. To perform the aforementioned, we are going to utilize technical procedures such as event-driven signal processing, pattern matching for signal recognition, and hardware in the loop simulation. We will also aim to implement the prototype of sensor processor based on Arduino MCU, which can be integrated with system using Arduino-Matlab/Simulink hybrid-interoperation environment. In the experiment, we use piezo transducer to detect the vibration or vibrates the surface using acoustic wave, which has specific frequency spectrum and individualized signal shape in terms of time axis. The signal distortion in time and frequency domain is recorded into memory tracer within sensor processor to extract the meaningful pattern by comparing the stored with lookup table(LUT). In this paper, we will contribute the initial prototypes for the acoustic touch processor by using off-the-shelf MCU and the integrated framework based on Matlab/Simulink model to provide the individualization of the touch-sensing for the user on purpose.

• Journal of the Ergonomics Society of Korea
• /
• v.30 no.2
• /
• pp.339-347
• /
• 2011

Objective: The purpose of this study was to evaluate of various material of pillows by using biomechanical variables such as the cervical stability, head pressure distribution, and muscle activity. Method: Eight subjects participated in the experiment. Three different materials such as polyester sponge, memory foam and the buckwheat shell used for Korean traditional pillow were tested. Electro-goniometer, six channels of electromyography(EMG), ten channels of the head pressure sensors were used to measure the biomechanical responses. Surface electrodes were attached to the right/left semispinals capitis(RSC, LSC), the right/left sternocleidomastoid(RSM, LSM), the right/left upper trapezius(RUT, LUT). The cervical stability was evaluated by the angle deviated from the standing neck position. The head pressure distribution was evaluated by the pressure per unit area recorded on the sensors and the intensity of peak pressure. Electromyography(EMG) data were analyzed by using root mean square(RMS) and mean power frequency(MPF). Results: The buckwheat shell material showed a higher stability in the cervical spine then the other pillows during spine position. In terms of head pressure distribution, the memory form indicated the lowest pressure at supine position, buckwheat shell material indicated the lowest pressure during lying down to side, and polyester cushion recorded the highest pressure at all postures. Conclusion: The buckwheat shell material has a biomechanical advantage to maintain a healthy neck angle and reduce the pressure on the head, which means the buckwheat shell is a potential material for ergonomic pillow design. The pillow with memory form showed second best biomechanical performance in this study. Application: The shape of the buckwheat shell pillow and the characteristics of materials can be used to design the pillow preventing neck pain and cervical disk problems.