• 한국소음진동공학회논문집
• /
• 제26권3호
• /
• pp.323-330
• /
• 2016

This paper describes real-time unbalance moment compensation method for line of sight(LOS) stabilization control systems. The factors of system inertia, frictions and unbalance moment affect the control accuracy of drive systems that are equipped to on the move(OTM) platforms requiring LOS stabilization function. In case of the unbalance moment among those factors is continuously changed as variation of relative angle between gravity vector and drive torque vector. Then, consideration of the effect in real-time is very complicate. Therefore, its effect should be designed to be minimized, however, designing it almost zero is impossible in real condition. In other words, it is hard to achieve target performance overcoming stability issue of highly unbalanced systems. To solve these problems, this paper proposes calculation method of unbalance moment by using measured sensor data for LOS stabilization control and its use for control compensation. Also, kinematical converting process and control structure for compensation are explained. The effectiveness of the proposed method as variation of unbalance moment is verified under simulation circumstance modeled by assuming LOS control system with 2-axis gimbal structure.

• 한국소음진동공학회논문집
• /
• 제21권10호
• /
• pp.951-959
• /
• 2011

In this study, an OTM(on-the-move) antenna which is mounted on ground vehicles and is used for mobile communication between vehicle and satellite while moving was addressed. Since LOS(line-of-sight) of antenna should direct satellite consistently while vehicle moving to guarantee high satellite communication quality, active antenna LOS stabilization is a core technology for OTM antenna. Stabilization of a satellite tracking antenna which consists of 2-DOF gimbals, an elevation gimbal over an azimuth gimbal, was considered in this study. In consideration of driving mechanism which consists of gear train and flexible driving shafts, a two-mass-system dynamic model coupled with vehicle motion was presented. An internal PI-control loop + outer PI-control loop structure has been suggested in order to damp the torsional vibration and stabilize control system. The classical pole-placement method was applied to design control gains. In addition, a vehicle motion compensation control beside of the feedback control loop has been suggested to improve LOS stabilization performances. The feasibility of the proposed control design was verified along with some experimental results.

• 한국군사과학기술학회지
• /
• 제26권1호
• /
• pp.72-82
• /
• 2023

The EOTS(Electro Optical Tracking System) must have stabilization performance to provide high-quality images under disturbance environment. In this paper, we present a controller that can minimize the LOS error and has a simple structure. Hence, to evaluate the performance of this controller, analysis in the frequency domain and LOS error measurement are performed. In order to measure the LOS error without a 'rate table' that requires a lot of facility investment, we propose a design method for disturbance model that considers the operating environment of the EOTS. Finally, the performance of the stabilization algorithm is evaluated by the proposed disturbance model.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.579-580
• /
• 2010

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1990년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 26-27 Oct. 1990
• /
• pp.643-647
• /
• 1990

Gunner primary sight(GPS) stabilization system lays line of sight(LOS) to find out a target and transmits informations to the fire control system (FCS). In a moving vehicle, accuracy of LOS and FCS depends on the design of GPS and servomechanism system. The heavy vibration of vehicle on the severe off-road environment degenerates the stabilization capability of GPS. In this study, to stabilize of elevation for GPS using the variable structure control, we derived the dynamic equation of GPS system and designed the variable structure controller. Computer simulation results fulfilled the static and dynamic stability of GPS using the variable structure control.

• 제어로봇시스템학회논문지
• /
• 제7권1호
• /
• pp.1155-1161
• /
• 2001

We propose an adaptive nonlinear control algorithm for high precision tracking and stabilization of LOS(Line-of-Sight). The friction parameters of the LOS gimbal are estimated by off-line evolutionary strategy and the friction is compensated by estimated friction compensator. Especially, as the nonlinear control input in a small tracking error zone is enlarged by the nonlinear function, the steady state error is significantly reduced. The proposed algorithm is a direct adaptive control method based on the Lyapunov stability theory, and its convergence is guaranteed under the limited modeling error or torque disturbance. The performance of the pro-posed algorithm is verified by computer simulation on the LOS gimbal model of a moving vehicle.

• 제어로봇시스템학회논문지
• /
• 제5권5호
• /
• pp.540-549
• /
• 1999

In this paper, the vibration suppression scheme based on a model referece approach is proposed. The vibration results from the coupling of the system and its frequency are given by the mechanical factors. In the proposed scheme, a low frequency vibration mode is transferred to high one. And also its damping ratio can be increased without any mechanical redesign. Therefore, bandwidth and open loop gain of the plant are increased and the performance of the system can be improved. This paper analyzes the proposed vibration suppression scheme, which is compared with the conventional control scheme for mechanical resonance suppression. For proving the realistic validity, we apply the proposed scheme to a LOS(Line Of Sight) stabilization system which has vibration effect. Finally, the proposed scheme is verified through simulations and experiments.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.1028-1032
• /
• 1996

Stabilization performance of a sight stabilization system can be improved by proper selection of control algorithm and mechanism. In that aspect, in this paper, effects of an inertia balancer are studied. Parameters of the inertia balancer were obtained from the governing equation by assuming there is no external force and friction. Simulation and experimental results show that the inertia balancer contributes significantly to the stabilization of the line of sight(LOS). In particular, it was found that the inertia balancer is more effective as frequency of the disturbance increases.

• 전기학회논문지
• /
• 제67권11호
• /
• pp.1555-1561
• /
• 2018

Tracking and detecting targets by the millimeter wave seeker is affected by movement of platform. Stabilization equipments use an inertial sensor to compensate for disturbance of stabilizing gimbal or platform. In the direct line of sight stabilization system, an inertial sensor is mounted on inner gimbal to compensate the disturbance directly, so the performance is excellent and the implementation method is simple. However gimbal design requires somewhat larger volume. Since an inertial sensor is mounted on gimbal base in the indirect line of sight stabilization system, additional space of gimbal is not required for the gimbal design. However, this method does not directly compensate for the disturbance of the line of sight stabilization axis, which can degrade performance. In order to perform the tracking performance, two methods are analyzed for line of sight stabilization performance based on direct and indirect of a 2-axis gimbaled servo system for millimeter wave seeker in this study. The simulation and experimental results validate the performance comparison of two methods.

• 한국군사과학기술학회지
• /
• 제16권1호
• /
• pp.89-94
• /
• 2013

Electro Otical Tracking System(EOTS) is required for a rapid movement as well as the stabilization of Line-Of-Sight(LOS). In order to achieve these two goals, this paper presents a position and velocity driving profile generation method from the constant acceleration and deceleration profile according to the current state, enabling a fast and smooth trajectory even if the target position changes during the movement of LOS. Simulation and experimental results reveal that the settling time could be reduced significantly by adopting the present position control scheme.