• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.6 no.2
• /
• pp.23-30
• /
• 2012

In this study, we developed a wireless rehabilitation auditory feedback gait training system for symmetrical weight-bearing in patient with CVA. The device consists of an instantaneous shoe equipped with two load-cell sensors. Auditory feedback can be applied according to the weight-bearing. For gait patterns analysis, cadence, walking velocity, stance/swing phase ratio and gait cycle were examined. The clinical test with six healthy volunteers and two hemiplegic patients was performed applying the auditory feedback system. Both normal subjects and hemiplegic patients were increased strength on weight-bearing in affected limb, walking velocity, and cadence after biofeedback device. Also, the stance time with weight-bearing was increased while the swing time was decreased in gait phase. It can be expected that by using the feedback system, the patient with lower limb disorder will be able to reach a better quality of weight-bearing during gait.

• Journal of the Institute of Convergence Signal Processing
• /
• v.16 no.2
• /
• pp.69-73
• /
• 2015

In this study, a method for estimating the amount of urination for men, was suggested and its performance was evaluated. This study is a preliminary one for the development of a health monitoring system that needs un-constraining, non-intrusive and long-term measurements in daily life. To estimate the amount of urination, a wide weighing plate with load cell was built and the difference in a man's weights between before and after urination was measured while he was standing on the plate. The results showed that the amount of urination can be estimated with the measured weight difference under the condition of mild movements. The largest measurement error of the suggested method was 40g, which means that this method can be applied to health monitoring in daily life. It is expected that the results of this study will be the basis for developing practical un-constraining and non-intrusive health monitoring system for daily use at home.

• Journal of Korea Society of Industrial Information Systems
• /
• v.22 no.5
• /
• pp.31-37
• /
• 2017

In this Paper, we have Improved the Manufacturing Process of Liquid Aluminum Sulfate using the Design of Automated Measurement Systems. The Manufacturing Process of Liquid Aluminum Sulfate uses a Large Weight. The Quality of a Product Depends Highly on the Proportion of the Raw Material Input in the Production Process. Therefore, it is Very Important to Accurately Measure the Amount of Raw Material. For Automation Design, Load Cell Sensor which can Measure Large Weight Accurately and PLC Technology which is most used in Automation Process are Applied. The Content of Aluminum Oxide in the Aluminum Sulfate Produced before the Automation Design Varies from 8.023% to 8.250%. However, after Automation Design, the Amount of Change from 8.09% to 8.19% was Greatly Reduced. As a Result, we could Reduce the Quality Defect rate Due to Weighing Errors and Reduce Safety Accidents by Applying Automation System.

• 대한공업교육학회지
• /
• v.32 no.1
• /
• pp.117-133
• /
• 2007

The purpose of this study was to develop the force measuring device of learning wind tunnel, teaching-learning materials in order to enhance understanding of flight principle and give interest about aviation technology in secondary school. The content of this study was consisted of the development and experiment of force measuring device for learning wind tunnel. The main results of this study were as follows: This device developed here is simple structure applying lever principle instead of the comparatively expensive load cell used in engineering college or a aviation research institute and so on. Measurement of lift and drag as well as the comparison experiment of a fluid resistance is possible with only one device developed here. The lift coefficient with angle of attack has shown the same tendency in both of theoretical and experimental values. And the stall phenomenon was found under the larger angle of attack of experimental rather than expected theoretical values. The drag coefficient with angle of attack has shown the same tendency in both of theoretical and experimental values. And drag coefficient the rate of increasement of the experimental values increased more gently than its theoretical values.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.2
• /
• pp.76-83
• /
• 2001

This study was carried out to clarify the mechanical behaviour of the earlywood and the latewood to the compressive load applied parallel to the grain. The results from the analysis of Japanese cedar wood (Cryptomeria japonica) were used to introduce a concept on stress-strain behaviour of the earlywood and the latewood. There was a significant differences in the mechanical behaviour of the earlyWood and the latewood. In the earlywood, the rate of cell wall upon annual ring was almost similar and the strain increased linearly with the stress increased. However, the rate of cell wall upon annual ring varied in the latewood and the strain of that increased curve-linearly with the stress increased. The longitudinal compression modulus of elasticity (MOE) variation by loading speed on latewood specimens and earlywood specimens shows no significant difference. The modulus of rupture (MOR) and MOE of latewood were about 4 times higher than those of earlywood.

• Proceedings of the KIEE Conference
• /
• 2001.05a
• /
• pp.190-193
• /
• 2001

In order to verify the efficiency or availability and stability of photovoltaic(PV) generation systems, huge system apparatuses are needed, in general, in which an actual size of solar panel, a type of converter system and some amount of load facilities should be installed in a particular location. It is also hardly possible to compare a Maximum Power Point Tracking (MPPT) control scheme with others under the same weather and load conditions in an actual PV generation system. The only and a possible way to bring above-mentioned problem to be solved is to realize a transient simulation scheme for PV generation systems using real weather conditions such as insolation and surface temperature of solar cell. The authors, in this paper, introduces a novel simulation method, which is based on a real-time digital simulator (RTDS), for PV generation systems under the real weather conditions. Firstly, VI characteristic equation of a solar cell is developed as an empirical formula and reconstructed in the RTDS system, then the real data of weather conditions are interfaced to the analogue inputs of the RTDS. The outcomes of the simulation demonstrate the effectiveness of the proposed simulation scheme in this paper. The results shows that the cost effective verifying for the efficiency or availability and stability of PV generation systems and the comparison research of various control schemes like MPPT under the same real weather conditions are possible.

• Journal of Mechanical Science and Technology
• /
• v.15 no.7
• /
• pp.1072-1076
• /
• 2001

A biomechanical study was conducted in this study to investigate if in-line skating wrist guards can effectively reduce the impact forces so as to protect the wrist from fracture. The forearm specimens with and without wrist guards were dropped using a specially designed sled to simulate the impact on the wrist while falling. A force plate was used to measure the total impact force on the dropping weight whereas a load cell was attached to the proximal end of the specimen and used to quantify the impact transmitted through the wrist joint. From the non-destructive tests, mean peak force measured from a force plate showed no difference between the guarded and unguarded groups whereas mean impulse of the guarded group was significantly greater than that of the unguarded group (p<0.01). Comparing the peak force and impulse measured from the load cell, the peak force of the guarded group was significantly less than that of the unguarded group (p<0.001), while the impulse values were similar. When the specimens were dropped from a higher position (2.5ft ve. 1ft), all unguarded specimens had severe wrist fractures whereas fracture was found in three out of 5 guarded specimens. Comparison of mean peak forces and impulses showed as significant difference between the guarded and unguarded groups only in the mean impulse measured from the force plate. These results suggest that the wrist guard may protect the wrist by attenuating the peak force transmitted to radius and ulnar although it may not be effective when the wrist is subjected to an impact sufficiently large to cause fractures.

• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.3
• /
• pp.138-144
• /
• 2013

New experimental devices and methods to measure shaft forces of ships are proposed in this paper. The strain gauge type six-component load cell was newly designed and installed to the end of the propeller shaft. The signals generated from the sensor in the propeller rotating are transferred to the new data amplifying and processing board on the shaft and the data is transmitted to the self-made wireless receiver. To find out the characteristics of shaft forces during port and starboard turning motions in sea trial, oblique and combined yaw maneuvering tests at straight, transient, maximum yaw rate, steady conditions were performed with the model ship installed the shaft forces measuring device using circular motion tester of Samsung Ship Model Basin. Characteristics of the measured shaft forces in model tests show quantitatively good agreement with the computed values obtained by the CFD programs using the measured wake data in oblique towing conditions. In the near future, It is hoped that the estimated shaft forces for a ship from this experimental method could be validated through comparison with directly measured values of a ship.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.640-649
• /
• 2010

Coarse granular materials such as gravel and crushed stone have been used as an important fill materials to large soil structure of railway, road, dam and so on. Although much studies for general soil materials have been carried out domestically, the studies for coarse materials were insufficient. Particularly, it is the level in which the study for dynamic properties(Elastic modulus and damping ratio) of coarse materials, applies the foreign country literature. This is due to the lack of large equipment for element test. But large soil structures made of coarse granular materials are generally important infrastructures. Therefore, the reliable design parameters for coarse materials should be obtained for safe and economic design, construction and maintenance. Triaxial test is the laboratory test method that is capable of controlling a confining pressure and boundary condition. In this project, we made a multi-purpose large triaxial testing system. This testing system is able to test coarse granular materials with maximum particle diameter of 100mm and support both the load control and displacement control. The load cell is installed inside of triaxial cell and the axial displacement is measured locally in order to control and measure more accurately in the small strain level. The verification test of this testing system was carried out with urethane verification specimens. So, from now on the useful information for coarse granular materials are expected to suggested by performing many tests with various material and condition.

• Korean Journal of Food Science and Technology
• /
• v.21 no.3
• /
• pp.387-390
• /
• 1989

Citrus fruit (Citrus unshiu Marc) were stored in the facillity controlled with a microprocessor-based storage controller, and the respiration rate and weight loss of fruits were measured with the infrared gas analyzer and the strain gauge load cell. The storage conditions and measuring intervals were set by the keyboard of personal computer. The interfacing cicuitry between the computer and Z-80 microprocerssor was built with peripheral Interfacing It chips 6821 and 8255. The data measured were saved to a data file for recording and further analysis. When the fresh and bruised fruits were subjected to the storage condition for 4 days at 20 C, the respiration rate of the fresh one showed a stable value of 3-5ml $CO_2/kg$ h throughout the storage period while the bruised one exihibited an abruptly increased rate after 50 hours. And the weight loss recorded about 5% during the storage.