• 제목/요약/키워드: LINK16

검색결과 535건 처리시간 0.027초

IEEE 802.16j 멀티홉 릴레이 네트워크를 위한 통합 자원 할당-라우팅 기법 (A Joint Resource Allocation and Routing Scheme for the IEEE 802.16j Multi-hop Relay Networks)

  • 이경주;이혁준
    • 한국ITS학회 논문지
    • /
    • 제8권1호
    • /
    • pp.82-91
    • /
    • 2009
  • 기지국과 이동 단말 간의 경로 설정, 즉 라우팅은 멀티홉 셀룰러 시스템의 핵심 기술 중 하나이다. 또한, 멀티홉 셀룰러 시스템에서 기지국과 중계기들이 각 셀의 자원을 공유하므로, 전체 시스템의 가용 무선 자원을 최대한 이용할 수 있는 자원 할당 기법이 필요하다. 본 논문에서는 OFDMA 기반 멀티홉 셀룰러 시스템을 위한 통합 자원할당-라우팅 기법을 제안한다. 제안하는 기법은 전체 시스템의 하향 링크 처리율을 최대화하기 위한 통합 자원 할당-라우팅 문제를 MMKP 기반 휴리스틱 알고리즘을 이용하여 근사 해를 구한다. 실험 결과는 제안하는 기법이 시스템의 하향 링크 처리율 측면에서 링크 품질 기반 라우팅 기법보다 높은 성능을 나타내며, 최적 해를 도출하는 기법에 근접한 성능을 나타냄을 보인다.

  • PDF

16Kbps SBC의 Rayleigh 페이딩 채널에러에 대한 강인성 연구 (A Study on the Robustness of a 16Kbps SBC over the Rayleigh fading Channel Error)

  • 오수환;이상욱
    • 한국통신학회논문지
    • /
    • 제11권4호
    • /
    • pp.287-295
    • /
    • 1986
  • 본 논문에서는 디지털 이동 무선통신을 위한 음성신호와 부호화 기법으로 SBC(sub-bnad coding)를 제안하고, SBC의 레일리(Rayleigh) 페이딩 채널에서의 음질의 강인성을 컴퓨터 시뮬레이션을 통해 조사하였다. 먼저 레일리 페이딩 채널, 시뮬레이터 및 16-ary DPSK(differential phase shift key) 수신기 모델을 제시한 후, 모델의 타당성을 이론치와 비교하여 입증하였다. 채널에러에 대한 영향은 SNR, LPC(linear predictive codin) 거리척도 및 주관적인 청각조사를 통해 검토하였다. BER(bit error rate) =$10_{-3}$, $10_{-2}$, 5$ imes$$10_{-2}$에 대한 시뮬레이션결과 BER=$10_{-2}$에서도 음성의 이해도는 확인되었으며, BER=5$ imes$$10_{-2}$에서도 음성통신에 사용하기는 충분하였다. 따라서 SBC는 ECC(error correction code) 사용없이 BER=$10_{-4}$~$10_{-2}$정도의 레일리 페이딩 채널에서 디지탈 이동무선통신에 응용이 가능함을 알 수 있었다.

  • PDF

Development of large bore superconducting magnet for wastewater treatment application

  • Liu, Huiming;Xu, Dong;Shen, Fuzhi;Zhang, Hengcheng;Li, Laifeng
    • 한국초전도ㆍ저온공학회논문지
    • /
    • 제19권1호
    • /
    • pp.13-16
    • /
    • 2017
  • Water issue, especially water pollution, is a serious issue of 21st century. Being an significant technique for securing water resources, superconducting magnetic separation wastewater system was indispensable. A large bore conduction-cooled magnet was custom-tailored for wastewater treatment. The superconducting magnet has been designed, fabricated and tested. The superconducting magnet was composed of NbTi solenoid coils with an effective horizontal warm bore of 400 mm and a maximum central field of 2.56T. The superconducting magnet system was cooled by a two-stage 1.5W 4K GM cryocooler. The NbTi solenoid coils were wound around an aluminum former that is thermally connected to the second stage cold head of the cryocooler through a conductive copper link. The temperature distribution along the conductive link was measured during the cool-down process as well as at steady state. The magnet was cooled down to 4.8K in approximately 65 hours. The test of the magnetic field and quench analysis has been performed to verify the safe operation for the magnet system. Experimental results show that the superconducting magnet reached the designed magnetic performance.

Influence of Job Embeddedness and Resilience on Turnover Intention in Dental Hygienists

  • Hwang, Ji-Min;Han, Ji-Hyoung
    • 치위생과학회지
    • /
    • 제20권3호
    • /
    • pp.171-177
    • /
    • 2020
  • Background: Maintaining a skilled workforce by minimizing the turnover of competent dental hygienists is very important for securing dental competitiveness. Therefore, it is necessary to find a predictor of turnover and lower turnover intention. To understand dental hygienist turnover, it is necessary to study the resilience, a positive factor of personal characteristics and job embeddedness that induces residual tissue. The purpose of this study was to investigate the effect of dental hygienists' job embeddedness and resilience on turnover intention. Methods: A survey was conducted on licensed dental hygienists nationwide, from March 19 to July 19, 2020. T-test and one way ANOVA analysis were performed to compare the job embeddedness, resilience, and turnover intention according to the general characteristics. Pearson's correlation analysis was performed to identify the correlation between job embeddedness, resilience, and turnover intention. Multiple regression analysis was performed to determine the effect on the turnover intention. Results: Job embeddedness was the highest with link and resilience scoring 3.57 and 4.16, respectively. The turnover intention scored 3.53. Among the general characteristics, age, marriage, total dental clinic career, education degree, and position showed statistically significant differences in job embeddedness, resilience, and turnover intention. Suitability, link, and sacrifice of job embeddedness were shown to affect the degree of turnover intention, with an explanatory power of 26.2%. Conclusion: In order to reduce the dental hygienists' turnover intention, job embeddedness and resilience should be increased. Thus, measures should be undertaken for professional and systematic program development and human resources management.

인버터 에어컨 시스템의 역률보상을 위한 AC-DC 컨버터 제어 (AC-DC Converter Control for Power Factor Correction of Inverter Air Conditioner System)

  • 박귀근;최재원
    • 제어로봇시스템학회논문지
    • /
    • 제13권2호
    • /
    • pp.154-162
    • /
    • 2007
  • In this paper, we propose a new AC-DC converter control method to comply with harmonics regulation(IEC 61000-3) effective for the inverter system of an air conditioner whose power consumption is less than 2,500W. There are many different ways of AC-DC converter control, but this paper focuses on the converter control method that is adopting an input reactor with low cost silicon steel core to strengthen cost competitiveness of the manufacturer. The proposed control method controls input current every half cycle of the line frequency to get unit power factor and at the same time to reduce switching loss of devices and acoustic noise from reactor. This kind of converter is known as a Partial Switching Converter(PSC). In this study, theoretical analysis of the PSC has been performed using Matlab/Simulink while a 16-bit micro-processor based converter has been used to perform the experimental analysis. In the theoretical analysis, electrical circuit models and equations of the PSC are derived and simulated. In the experiments, micro-processor controls input current to keep the power factor above 0.95 by reducing the phase difference between input voltage and current and at the same time to maintain a reference DC-link voltage against voltage drop which depends on DC-link load. Therefore it becomes possible to comply with harmonic regulations while the power factor is maximized by optimizing the time of current flow through the input reactor for every half cycle of line frequency.

통계적 구간 추정에 근거한 비용과 지연시간에 조화로운 유니캐스트 라우팅을 위한 새로운 인자 (New Factor for Balancing Cost and Delay Unicast Algorithm Based on Statistic Interval Estimation)

  • 김문성;방영철;추현승
    • 한국시뮬레이션학회논문지
    • /
    • 제16권1호
    • /
    • pp.1-9
    • /
    • 2007
  • 고속 네트워크에서 QoS 라우팅은 수많은 사용자의 요구를 만족하기가 매우 어렵다. 네트워크의 경로설정 알고리즘에서 측도로써 단지 링크지연시간만을 고려한다면 그 경로는 최소지연시간 경로가 될 것이며, 링크비용만을 고려한다면 최소비용경로를 찾을 것이다. 지연시간 한계의 최소비용(Delay Constrained Least Cost; DCLC)문제는 NP-hard 문제로 알려져 있으며, 두 개의 인자 경로비용과 지연시간을 혼합한문제로 생각할 수 있다. 경로설정 시 최소지연시간을 생각하면 그 경로는 상대적으로 높은 비용의 경로이며, 반대로 최소비용만을 생각하면 그 경로는 상대적으로 높은 지연시간을 얻는다. 따라서 DCLC문제를 풀기위해서는 단 하나의 인자만을 고려해서는 안 되며 두 개의 인자를 동시에 고려할 수 있는 새로운 인자를 요구하게 되었다. 따라서 본 논문에서는 DCLC 문제를 풀기위해 경로비용과 지연시간을 동시에 확률적으로 고려한 새로운 인자를 소개한다. 시뮬레이션 결과는 새로운 인자가 DCLC 문제에 적절하다는 것을 보여주었다.

  • PDF

Effect of antioxidants on push-out bond strength of hydrogen peroxide treated glass fiber posts bonded with two types of resin cement

  • Khoroushi, Maryam;Mazaheri, Hamid;Tarighi, Pardis;Samimi, Pouran;Khalighinejad, Navid
    • Restorative Dentistry and Endodontics
    • /
    • 제39권4호
    • /
    • pp.303-309
    • /
    • 2014
  • Objectives: Hydrogen peroxide ($H_2O_2$) surface treatment of fiber posts has been reported to increase bond strength of fiber posts to resin cements. However, residual oxygen radicals might jeopardize the bonding procedure. This study examined the effect of three antioxidant agents on the bond strength of fiber posts to conventional and self-adhesive resin cements. Materials and Methods: Post spaces were prepared in forty human maxillary second premolars. Posts were divided into five groups of 8 each: G1 (control), no pre-treatment; G2, 10% $H_2O_2$ pre-treatment; G3, G4 and G5. After $H_2O_2$ application, Hesperidin (HES), Sodium Ascorbate (SA) or Rosmarinic acid (RA) was applied on each group respectively. In each group four posts were cemented with Duo-Link conventional resin cement and the others with self-adhesive BisCem cement. Push-out test was performed and data were analyzed using 2-way ANOVA and tukey's post-hoc test (${\alpha}=0.05$). Results: There was a statistically significant interaction between the cement type and post surface treatment on push-out bond strength of fiber posts (p < 0.001, F = 16). Also it was shown that different posts' surface treatments significantly affect the push-out bond strength of fiber posts (p = 0.001). $H_2O_2$ treated posts (G2) and control posts (G1) cemented with Duo-link showed the highest ($15.96{\pm}5.07MPa$) and lowest bond strengths ($6.79{\pm}3.94$) respectively. Conclusions: It was concluded that $H_2O_2$ surface treatment might enhance the bond strength of fiber posts cemented with conventional resin cements. The effect of antioxidants as post's surface treatment agents depends on the characteristics of resin cements used for bonding procedure.

연평균 일일교통량을 이용한 일반국도구간 연간 총통행시간 추정 방법 개발 (Estimation of Total Travel Time for a Year on National Highway Link with AADT)

  • 김정현;서선덕;김태희
    • 대한토목학회논문집
    • /
    • 제29권1D호
    • /
    • pp.11-16
    • /
    • 2009
  • 도로 및 철도 등의 투자평가에 있어 도로부문에서 발생하는 통행시간 절감편익의 추정이 가장 중요한 부문을 차지한다. 우리나라에서 현재 적용되고 있는 대부분의 교통시설 투자평가지침은 BPR 함수의 시간-교통량 관계를 이용하고 있으며, 연평균일일교통량(AADT)에 첨두시간 교통량의 비율(설계시간 계수)을 곱한 교통량을 기준으로 산출되고 있다. 그러나 AADT 에 설계시간계수를 적용하는 문제와 우리나라의 많은 도로구간이 거의 용량상태에 다다르고 있는 상황 등으로 인하여 총통 행시간이 과다추정되는 것에 대한 문제제기가 있어왔다. 본 연구에서는 기존의 방식을 대신하여, 일년간 시간대별 교통량 분포를 이용하여 총통행시간을 산출함으로써 이러한 문제를 극복하여 보다 현실성 있는 통행시간을 추정할 수 있는 방법을 제 시하였다. 일반국도를 대상으로 이 방법론의 적용효과를 분석하였으며, 이 방법론은 도로의 위계 및 유형별로 AADT를 제공하게 되면 다른 유형의 도로에 대하여서도 적용될 수 있을 것이다.

스포트라이트 - 기다렸다 드루파2012!! 인쇄와 연결되는 모든 것 'Your Link to print'

  • 임남숙
    • 프린팅코리아
    • /
    • 제11권4호
    • /
    • pp.86-104
    • /
    • 2012
  • 4년마다 개최돼 인쇄 산업의 올림픽이라고 불리는 세계 최대 규모의 인쇄 기술 전시회인 드루파2012가 5월 3일부터 16일까지 독일 뒤셀도르프에서 개최된다. 전 세계 인쇄산업을 선도하는 전문 전시회인 드루파는 인쇄 산업과 기술을 비롯해 관련 산업 및 경제에 막대한 영향을 주는 전 세계 인쇄인들의 축제다. 전 세계 약 140개 국가에서 40만여 명이 드루파2012를 관람하기 위해 뒤셀도르프로 모여들 것으로 보인다. 방문객의 약 60%가 지난 드루파2008과 마찬가지로 독일 외 지역에서 오는 외국 방문객이다. 이는 드루파 전시회의 뛰어난 국제성을 증명하는 수치로 다른 어떤 전시회와도 비교할 수 없는 국제적 흡인력을 보여준다. 또한 40만 명의 방문객 중 약 78%가 각 기업 내 의사 결정권을 가진 주요 인사들이며 드루파 방문객의 98%는 재방문객이다. 이러한 결과는 드루파는 인쇄인들에게 필수 전시회라는 점을 보여준다.

  • PDF

Demonstration of RSOA-Based 20 Gb/s Linear Bus WDM-PON with Simple Optical Add-Drop Node Structure

  • Lee, Han-Hyub;Cho, Seung-Hyun;Lee, Eun-Gu;Lee, Sang-Soo
    • ETRI Journal
    • /
    • 제32권2호
    • /
    • pp.248-254
    • /
    • 2010
  • We demonstrate a linear bus wavelength-reused gigabit wavelength-division multiplexing passive optical network (WDM-PON) with multiple optical add-drop nodes. A commercially available reflective semiconductor optical amplifier-based WDM-PON has a sufficient power budget to provide multiple optical add/drop nodes in 16 WDM channels. Sixteen 1.25 Gb/s WDM channels are successfully transmitted over 20 km of single-mode fiber with four optical add/drop multiplexers, even with 32 dB reflection and chromatic dispersion in the link.