• Current Photovoltaic Research
• /
• v.9 no.3
• /
• pp.84-95
• /
• 2021

The power conversion efficiency of Cu₂ZnSnSe₄ (CZTSe) solar cells depends on the absorber layer thickness; however, changes in the characteristics of the cells with varying absorber layer thickness are unclear. In this study, we investigated the changes in the characteristics of CZTSe solar cells for varying absorber layer thickness. Five absorber thicknesses were employed: CZTSe1 2.78 ㎛, CZTSe2 1.01 ㎛, CZTSe3 0.55 ㎛, CZTSe4 0.29 ㎛, and CZTSe5 0.15-0.23 ㎛. The efficiency of the CZTSe solar cells decreased as the absorber thickness decreased, resulting in power conversion efficiencies of 10.45% (CZTSe1), 8.67% (CZTSe2), 7.14% (CZTSe3), 3.44% (CZTSe4), and 1.54% (CZTSe5). As the thickness of the CZTSe absorber layer decreased, the electron-hole recombination at the grain boundaries and the absorber-back-contact interface increased. This caused an increase in the current loss, owing to light loss in the long-wavelength region. In addition, as the thickness of the CZTSe absorber layer decreased, more ZnSe was produced, and the resulting defects and defect clusters led to an open-circuit voltage loss.

• Korean Journal of Metals and Materials
• /
• v.46 no.10
• /
• pp.683-690
• /
• 2008

In order to develop transparent electrodes for high efficiency GaN-based light emitting diodes (LEDs), the electrical and optical properties of the electron beam evaporated ITO contacts have been investigated as a function of the deposition temperature and flow rate of oxygen during the deposition. As the deposition temperature increases from $140^{\circ}C$ to $220^{\circ}C$, the resistivity of the ITO films decreases slightly from $4.0{\times}10^{-4}{\Omega}cm$ to $3.3{\times}10^{-4}{\Omega}cm$, meanwhile the transmittance of the ITO films significantly increases from 67% to 88% at the wavelength of 470 nm. When the flow rate of oxygen during the deposition increases from 2 sccm to 4 sccm, the resistivity of the ITO films increases from $3.6{\times}10^{-4}{\Omega}cm$ to $7.4{\times}10^{-4}{\Omega}cm$, meanwhile the transmittance of the ITO films increases from 86% to 99% at 470 nm. Blue LEDs fabricated with the electron beam evaporated ITO electrode show that the ITO films deposited at $200^{\circ}C$ and 3 sccm of the oxygen flow rate give a low forward-bias voltage of 3.55 V at injection current of 20 mA with a highest output power.

• Journal of Digital Convergence
• /
• v.19 no.11
• /
• pp.341-349
• /
• 2021

We studies to verify results similar to those of previous experiments, and their potential as a lighting device through optical characteristics experiments and resonance and optical characteristics simulations of array devices. The photonic quantum ring (PQR) device having a mesa diameter of 40 ㎛ and an internal hole diameter of 3 ㎛ was fabricated. Through the near-field observation of the fabricated device, it was found that the PQR device operates even at ㎂, and also that the mesa and hole devices are driven independently of each other. As a result of measuring the wavelength spectrum of the device according to the location, the coupling phenomenon due to mesa and holes was confirmed.

• Medical Lasers
• /
• v.8 no.2
• /
• pp.50-58
• /
• 2019

Background and Objectives Low-level light therapy (LLLT) is an application of low-power light for various purposes such as promoting tissue repair, reducing inflammation, causing analgesia, etc. A previous study suggested the effect of light emitting diode (LED) light with the wavelength of 740 nm for promoting wound healing of corneal epithelial cells. This current study aimed to confirm the effect of LLLT for managing inflammation of a dry eye disease (DED) mouse model. Materials and Methods A total of 50C57BL/6 female mice were randomly grouped into 5 groups to compare the effect of LLLT:1) Control group, 2) Only LLLT group, 3) Dry eye group, 4) LLLT in dry eye group, and 5) Early treatment group. DED was induced with 4 daily injections of scopolamine hydrobromide and desiccation stress for 17 days, and LLLT at 740 nm was conducted once every 3 days. To analyze the effect of LLLT on the DED mouse model, tear volume, corneal surface irregularities, and fluorescence in stained cores were measured, and the level of inflammation was assessed with immunohistochemistry. Results The DED mouse model showed significant deterioration in the overall eye condition. After LLLT, the amount of tear volume was increased, and corneal surface irregularities were restored. Also, the number of neutrophils and the level of inflammatory cytokines significantly decreased as well. Conclusion This study showed that LLLT at 740 nm was effective in controlling the corneal conditions and the degree of inflammation in DED. Such findings may suggest therapeutic effects of LLLT at 740 nm on DED.

• Journal of Bio-Environment Control
• /
• v.23 no.1
• /
• pp.19-25
• /
• 2014

In this study, we analyzed the growth characteristics of red lettuce under Light-emitting diode (LED) light environment as well as the change of vitamin C and anthocyanins of lettuce. We made five monochromatic light treatments (red 647 nm, 622 nm, blue 463 nm, 450 nm, White), six mixed red (R) and blue (B) light treatments (R : B = 9 : 1, 8 : 2, 7 : 3, 6 : 4, 5 : 5) and red + white, and three light treatments made according to photoperiod of LED with lighting sources ratio of red : blue (R : B = 8 : 2(18/06 h, 15/09 h, 12/12 h)). It was composed of totally 14 control beds. As a result, the red lettuce the most developed leaf height, leaf numbers and fresh weight under red single light, root length and leaf developed when grown under blue single light. Therefore, red light were related to above part of the lettuce, blue light were related to the growth of the underground part of lettuce. Case of the mixed light, leaf height, leaf numbers, fresh/dry weight of above and underground part were highest red + white light and root length and chlorophyll content were highest under red 7 : 3 blue light. Result of growing investigation by photoperiod, the red lettuce were considered to be most effective in 15/09 h (on/off). The content of anthocyanins; the single light source, mixed light and light irradiation period were highest under blue light (463 nm), red 7 : 3 blue and 18/06 h (on/off) light irradiation, respectively. The vitamin C showed the lowest content of $1.26mg{\cdot}L^{-1}$ under the white light, but showed the greatest content of $3.02mg{\cdot}L^{-1}$ for the control group.

• Journal of Bio-Environment Control
• /
• v.19 no.4
• /
• pp.351-359
• /
• 2010

To establish the optimum artificial light illumination method for baby leaf lettuce in closed plant factory system, the effects of red/blue light quality and short-term light quality conversion on growth and anthocyanin content were investigated. The growth of 'Hongha' lettuce was most favorable under red single wavelength LED light after 23 days of treatment, sequentially followed by the growth under red/blue mixed light, blue light, and fluorescent light. Total anthocyanin content in the mixed red/blue light (R57-B43) was 4.1-fold and 6.9-fold increased compared to the red LED and fluorescent light, respectively. With increasing the blue light ratio to 43%, the growth of lettuce was significantly decreased, while the relative chlorophyll content and Hunter's $a^*$ value was increased, indicating that the red/blue light ratio inversely affects on growth and anthocyanin pigment development. By changing light quality from red to red/blue mixed light source (R57-B43) for 9 days before harvest, the growth rate decreased compared to the continuous red light illumination, while the anthocyanin content dramatically increased compared to either red LED or fluorescent light. Whereas, when the light source was changed to red light, the growth rate was increased but anthocyanin content was reversely decreased. The result demonstrated that both growth and anthocyanin expression could be effectively regulated by shifting of light quality between red and red/blue mixed light source at a specific growth stage of lettuce in a plant factory.

• Journal of Bio-Environment Control
• /
• v.22 no.4
• /
• pp.392-399
• /
• 2013

This study aimed to investigate responses of photosynthesis, plant growth, and phytochemical contents to different artificial light sources for 'Seneca RZ' and 'Gaugin RZ' two butterhead lettuce (Lactuca sativa L.). In this study, fluorescent lamps (FL), three colors LEDs (red, blue and white, 5 : 4 : 1; RBW) and metalhalide lamps (MH) were used as artificial lighting sources. Photoperiod, air temperature, relative humidity, EC, and pH in a cultivation system were maintained at 16/8 h, $25/15^{\circ}C$, 60~70%, $1.4{\pm}0.2dS{\cdot}m^{-1}$, and $6.0{\pm}0.5$, respectively. The photosynthetic rate of both two butterhead lettuce were the highest under RBW in middle growth stage. However, in late growth stage, the photosynthetic rate of both two butterhead lettuce were higher under RBW and MH than FL. The light sources showed significant results for plant growth but those effects were different to variety. Fresh and dry weight of 'Gaugin RZ' butterhead lettuce under MH were heavier than other lights in all growth stages. Growth of 'Seneca RZ' butterhead lettuce was maximized highest under MH in middle growth stage and FL in late growth stage. In the leaf tissue of 'Seneca RZ' butterhead lettuce, tipburn symptom occurred under all light sources and in the leaf tissue of 'Gaugin RZ' butterhead lettuce, it occurred under two light sources except for fluorescent lamps in late growth stage. kinds of lamp affect plant growth more than plant quality. Relative growth rate of both two butterhead lettuce was faster in middle growth stage than late stage. Growth of 'Gaugin RZ' was shown by kinds of lamp in middle growth stage and but it was not significantly affected by light sources and variety in late stage. Most of the phytochemical contents of two butterhead lettuce were significantly affected by different light sources. Contents of all vitamins showed higher than other light sources on RBW for both two lettuce, especially ${\beta}$-Carotene content of 'Gaugin RZ' was the highest. Plant growth, photosynthesis, and phytochemical contents were observed significant effects by different light sources for two butterhead lettuce but those effects were highly different between variety and kinds of phytochemicals. Therefore, the selection of optimum light source should be considered by variety and kinds of phytochemicals in the plant factory.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.58.1-58.1
• /
• 2010

In solar cell module manufacturing, single solar cells has to be joined electrically to strings. Copper stripes coated with tin-silver-copper alloy are joined on screen printed silver of solar cells which is called busbar. The bus bar collects the electrons generated in solar cell and it is connected to the next cell in the conventional module manufacturing by a metal stringer using conventional hot air or infrared lamp soldering systems. For thin solar cells, both soldering methods have disadvantages, which heats up the whole cell to high temperatures. Because of the different thermal expansion coefficient, mechanical stresses are induced in the solar cell. Recently, the trend of solar cell is toward thinner thickness below 180um and thus the risk of breakage of solar cells is increasing. This has led to the demand for new joining processes with high productivity and reduced error rates. In our project, we have developed a new method to solder solar cells with a laser heating source. The soldering process using diode laser with wavelength of 980nm was examined. The diode laser used has a maximum power of 60W and a scanner system is used to solder dimension of 6" solar cell and the beam travel speed is optimized. For clamping copper stripe to solar cell, zirconia(ZrO)coated iron pin-spring system is used to clamp both joining parts during a scanner system is traveled. The hot plate temperature that solar cell is positioned during lasersoldering process is optimized. Also, conventional solder joints after $180^{\circ}C$ peel tests are compared to the laser soldering methods. Microstructures in welded zone shows that the diffusion zone between solar cell and metal stripes is better formed than inIR soldering method. It is analyzed that the laser solder joints show no damages to the silicon wafer and no cracks beneath the contact. Peel strength between 4N and 5N are measured, with much shorter joining time than IR solder joints and it is shown that the use of laser soldering reduced the degree of bending of solar cell much less than IR soldering.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.345-346
• /
• 2013

InGaN material is being studied increasingly as a prospective material for solar cells. One of the merits for solar cell applications is that the band gap energy can be engineered from 0.7 eV for InN to 3.4 eV for GaN by varying of indium composition, which covers almost of solar spectrum from UV to IR. It is essential for better cell efficiency to improve not only the crystalline quality of the epitaxial layers but also fabrication of the solar cells. Fabrication includes transparent top electrodes and surface texturing which will improve the carrier extraction. Surface texturing is one of the most employed methods to enhance the extraction efficiency in LED fabrication and can be formed on a p-GaN surface, on an N-face of GaN, and even on an indium tin oxide (ITO) layer. Surface texturing method has also been adopted in InGaN-based solar cells and proved to enhance the efficiency. Since the texturing by direct etching of p-GaN, however, was known to induce the damage and result in degraded electrical properties, texturing has been studied widely on ITO layers. However, it is important to optimize the ITO thickness in Solar Cells applications since the reflectance is fluctuated by ITO thickness variation resulting in reduced light extraction at target wavelength. ITO texturing made by wet etching or dry etching was also revealed to increased series resistance in ITO film. In this work, we report a new way of texturing by deposition of thickness-optimized ITO films on ITO nano dots, which can further reduce the reflectance as well as electrical degradation originated from the ITO etching process.

• Korean Journal of Optics and Photonics
• /
• v.23 no.2
• /
• pp.64-70
• /
• 2012

We analyzed the changes in electrical and optical characteristics of 1 $mm^2$ multiple-quantum-well (MQW) blue LEDs grown on a c-plane sapphire substrate after a stress test. Experiments were performed by injecting 50 mA current for 200 hours to TO-CAN packaged sample chips. We selected the value of injection current for stress through the junction-temperature measurement by using the forward-voltage characteristics of a diode to maintain a sufficiently low junction temperature during the test. The junction temperature at the selected injection current of 50 mA was 308 K. Experiments were performed under the assumption that the average junction temperature of 308 K did not affect the characteristics of the ohmic contact and the GaN-based materials. Before and after the stress test, we measured and analyzed current-voltage, light-current, light distribution on the LED surface, wavelength spectrum and relative external quantum efficiency (EQE). After the stress test, it was observed experimentally that the optical power and the relative EQE decreased. We theoretically investigated and experimentally proved that these phenomena are due to the increased nonradiative recombination rate caused by the increased defect density.