• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.2
• /
• pp.445-451
• /
• 2014

Dual LED lantern, which is composed of two light sources in one lantern, can be utilized as an auxiliary light source when the main light source is in trouble. Nevertheless, there are no way to obtain status information of the system and control the light source if the current domestic standard protocol is applied, since the standards for dual LED lantern are not defined yet. Regarding to this problem, we suggested expanded lantern protocol for management system of dual LED lantern based on current domestic standard. Also, we confirmed the normal operation of dual LED lantern after implementing suggested protocol on the developed management system. Control system suggested and implemented in this study is tested not only its function of controlling and acquiring the operating status of dual LED lantern, but also its capability to utilize as a control system of currently used LED lanterns.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.6
• /
• pp.488-492
• /
• 2013

Current limiting diode (CLD) was fabricated using junction field effect transistor (JFET) structured two small cells and eight large cells. Two small cells and eight large cells were connected in parallel and the obtained constant current was 110 mA. The application of CLD in each of the parallel circuits on chip on board (COB) type LED lighting source, could significantly reduce the current deviation within the parallel circuits. The applications of CLD on AC power small lighting source, battery power low voltage parallel lighting source and AC flat lighting source were investigated.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.9
• /
• pp.2160-2166
• /
• 2013

The usability of marine lantern has been improved significantly by using the LED bulb and applying IT technology, However it is hard to fix immediately when the failure occurs, and there would be some additional costs in maintenance. Therefore, alternatives for those problems are required. In this regard, in this paper, we proposed the integrated duel-function LED marine lantern that has main and auxiliary light source at the same time so that it can operate auxiliary light source when the main light source has breakdowns or malfunctions.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1642-1645
• /
• 2007

The brightness of LED changes according to the current flowing through LEDs. The current mirror was used to drive LEDs effectively. The reference current of the current mirror was usually controlled by the resistor but the size of this resistor is very large and this resistor consumes too much power for high power LED backlight driving. The reference current of the current mirror LED driver was controlled by using flyback converter at small size with low power consumption in this paper. The concept of active current source was presented.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.743-744
• /
• 2010

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.3
• /
• pp.20-26
• /
• 2004

In this paper, luminaire optical efficiency and luminous intensity according to array of HB(high brightness) white LED(light emitting diode) and globe types of luminaire were simulated by computer and made a comparative analysis. LEDs were arranged by square of 7ea X 7ea. LED space has been divided into 8.2mm, 10mm and 15mm that mean distances between luminous centers of LEDs, and luminaire globes were classified into 30mm and 50mm 묘묘 from luminous center of LEDs. Also the simulations were made with / without globe, globe types were specified by convex and embossing types of which sizes are 8.2mm and 5.0mm, So total 27 classes of simulation were performed. This paper is to help luminire development using LED light source called digital lighting of 21th century, by studying luminire effciency and luminous intensity of different types of globes.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.2050-2055
• /
• 2009

This paper describes the proceeding experimental results to replace the 32 [W] fluorescent lamp installed in subway train to a LED module. We fabricated 25 [W] LED modules to meet the illuminance 300 [lx] specified in the standard for subway train. After the installation of LED modules, comparative analysis with conventional fluorescent lamps was carried out. From the experimental results, illuminances on the height of 0.85 [m] and 1 [m] above floor were 323 [lx] and 360 [lx], respectively. These illuminances satisfied the requirement 300 [lx]. By the application of 25 [W] LED module as a light source in subway train, energy saving about 22 [%] compared with 32 [W] fluorescent is acquired. Also, low cost of maintenance is expected due to 8 times longer lifetime 50,000 hours of LED than that 6,000 hours of fluorescent lamp.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.12
• /
• pp.60-66
• /
• 2011

There are several technological problems have to be resolved for LEDs to be used as a general purpose light source. In addition, there are several differences between existing luminaires and the general planer LED luminaire for the intensity distribution. Therefore, the optical engineer then faces the challenging a problem of designing for a spatially extended and non-uniform light source. In the previous studies on the optical design of luminaires, a lot of studies on reflectors and light source have been conducted but the ones on prisms and lenses are insufficient at present. This study developed the numerical model of planar prism LED luminaire to control luminous intensity distribution of LED luminaires. And this study presents an optical calculation process for the prism optical design of a planar prism LED luminaire and a comparison of the simulation results between the developed numerical model and Photopia 2.0 to verify the accuracy of the numerical model. In addition, this study showed a method for the control of various luminous intensity distribution from the developed numerical model.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.284-284
• /
• 2009

The LED of cultivation edible plants was compliance the variable of the photo-receptor pigment with the red light source and ultra red light source from long wave region. The mechanism of cultivation edible plants for each part was necessary the wavelength unit which is appropriate, the illuminant source, motor control and lens design of LED light source about plant. The photo-receptor pigment induces for a long daytime recognition, seed germination and anthesis etc, induction years exists in the state which is an inactivity within the cells and in compliance with the red light source to be converted in active

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.5
• /
• pp.587-592
• /
• 2015

According to increase in the use of the LED, the demand for low power consumption LED display design of the controller block has increased. In this paper, the low power LED controller block was designed through the power source supply that leads adiabatic operation from constant current source circuit operated by digital signal control. The proposed circuit was implemented using a 0.35um CMOS process. and it demonstrated linear operation of the circuit. From the simulation result, the proposed circuit was evaluated with about 82% power consumption reduction effect in comparison with conventional LED controller block. This research is expected to be helpful for the low power operation and the solution for heat problem of LED display.