• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.8
• /
• pp.215-221
• /
• 2020

Navigation lights used in supersonic aircraft are used to identify the direction and location of the aircraft. The color of the navigation lights and location of installation are defined by aviation law as red for the left wing, green for the right wing, and white for the tail. Navigation lights operate in BRT and DIM modes. BRT is the brightest mode, and DIM is an output with dimmed brightness. Navigation lights serve to prevent aircraft collisions and are very important for stability and location identification. One phenomenon is that the inlet and tail navigation lights flicker abnormally. In this study, fault tree analysis was performed in two stages. The first step was derived from three causal factors, the second step developed five improvements, and the optimal improvement plan was drawn. The navigation lights confirmed that the initial input power was unstable as the main cause of abnormal flickering. As an improved method, the circuit was adjusted to stabilize the initial power, and it was confirmed that flickering did not occur as a result of the tests under the same conditions.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.53 no.spc
• /
• pp.84-88
• /
• 2008

This study was carried out to develop the methods for efficient extracting and stabilization of anthocyanin pigments in black colored soybean. The optimum solvent concentration for the highest pigment extraction from seed coat of black colored soybean was 60% MeOH with 0.1% HCl in laboratory test. The higher temperature of the solvent until $60^{\circ}C$ led to better extraction efficiency of anthocyanin. The anthocyanin extracts maintained almost its stability in strong acidity area whereas it destroyed markedly over pH 4. Also anthocyanin extracts was stable for a while under weak light condition, but it showed rapid degradation of pigment color and markedly decreased HPLC value for anthocyanin content after one month storage days. In case storage temperature and instrument, glass vessel on low temperature ($4^{\circ}C$) was good storage condition among some treatments. And C3G was more stable than other pigments.

• 한국균학회소식:학술대회논문집
• /
• 2014.05a
• /
• pp.21-21
• /
• 2014

A edible mushroom, Hypsizygus marmoreus is commercially cultivated in Northeast Asia. Japan's annual production is 110,000ton or more. Since 2002, cultivation is expanded in Korea. To investigate the morphological, cultural and microscopic characteristics of Hypsizygus marmoreus, 109 isolates were collected from Korea and other countries. Clamp connection, chlamydospore and arthrospore were present in all tested isolates of H. marmoreus except HYM-002 and HYM-004. Also pilealtrama, gilltrama, basidia, basidiospore and cystidia of fruiting body were no difference among the isolates in the present investigation. Morphological characteristics of fruiting body was that color of pileus was brown and white, irregular as marble, the average size 12~22mm and stipes was $46{\sim}91{\times}6{\sim}10mm$. Isolates HYM-031, HYM-047 and HYM-109 formed grayish-brown pileus with a faint pattern. Molecular analysis with RAPD and ITS rDNA sequence analysis were also performed to check the genetic relationships among H. marmoreus isolates. Based on the RAPD analysis using the URP-PCR, all isolates of H. marmoreus were clustered into large 3 groups but more than 90% showed high similarity. In addition, morphological and geographical differences have been classified as an independent cluster. The brown and white strains enclosed in same cluster. So genetically no significance difference was observed between these two strains. ITS gene sequences of 16 selected isolates which were 640 bp long, were aligned and compared. The similarity in ITS sequence was 94.8 to 99.1% among tested isolates and the H. marmoreus isolates in GeneBank. In conclusion the tested isolates were H. marmoreus. Morphological and molecular observations proved that all tested isolates were belonging to H. marmoreus. For the stable artificial cultivation, composition of optimum media, mature period and light condition were established. Optimal formula of artificial cultivation medium was Douglas sawdust: corn cob: soybean meal: wheat bran = 40:30:15:15. In addition, 7% rice bran and 3% yellow sucrose was the most effective composition for spawn's liquid medium. For the maturation of the isolates was favorable for growing for 20 to 30 days at $25^{\circ}C$ and the LED lights in mixture of white and blue was good for growth period. For effective growth, the temperature, humidity and aeration control in every step was important.

• Parasites, Hosts and Diseases
• /
• v.55 no.4
• /
• pp.409-416
• /
• 2017

The high prevalence of pediculosis capitis, commonly known as head lice (Pediculus humanus capitis) infestation, has led to the preparation of a community-based pediculicidal ointment, which is made of common household items and the extract of Tinospora crispa stem. The present study aimed to evaluate the safety, efficacy, and physicochemical characteristics of the T. crispa pediculicidal ointment. The physicochemical properties of the ointment were characterized, and safety was determined using acute dermal irritation test (OECD 404), while the efficacy was assessed using an in vitro pediculicidal assay. Furthermore, the chemical compounds present in T. crispa were identified using liquid-liquid extraction followed by ultra-performance liquid chromatography quadruple time-of-flight mass spectrometric (UPLC-qTOF/MS) analysis. The community-based ointment formulation was light yellow in color, homogeneous, smooth, with distinct aromatic odor and pH of $6.92{\pm}0.09$. It has spreadability value of $15.04{\pm}0.98g{\cdot}cm/sec$ and has thixotropic behavior. It was also found to be non-irritant, with a primary irritation index value of 0.15. Moreover, it was comparable to the pediculicidal activity of the positive control $Kwell^{(R)}$, a commercially available 1% permethrin shampoo (P>0.05), and was significantly different to the activity of the negative control ointment, a mixture of palm oil and candle wax (P<0.05). These findings suggested that the community-based T. crispa pediculicidal ointment is safe and effective, having acceptable physicochemical characteristics. Its activity can be attributed to the presence of compounds moupinamide and physalin I.

• Journal of Sensor Science and Technology
• /
• v.29 no.1
• /
• pp.27-32
• /
• 2020

This study proposes a pixel-patterning method for organic light-emitting diodes (OLEDs) based on thermal transfer. An infrared lamp was introduced as a heat source, and glass type donor element, which absorbs infrared and generates heat and then transfers the organic layer to the substrate, was designed to selectively sublimate the organic material. A 200 nm-thick layer of molybdenum (Mo) was used as the lightto-heat conversion (LTHC) layer, and a 300 nm-thick layer of patterned silicon dioxide (SiO₂), featuring a low heat-transfer coefficient, was formed on top of the LTHC layer to selectively block heat transfer. To prevent the thermal oxidation and diffusion of the LTHC material, a 100 nm-thick layer of silicon nitride (SiN_x) was coated on the material. The fabricated donor glass exhibited appropriate temperature-increment property until 249 ℃, which is enough to evaporate the organic materials. The alpha-step thickness profiler and X-ray reflection (XRR) analysis revealed that the thickness of the transferred film decreased with increase in film density. In the patterning test, we achieved a 100 ㎛-long line and dot pattern with a high transfer accuracy and a mean deviation of ± 4.49 ㎛. By using the thermal-transfer process, we also fabricated a red phosphorescent device to confirm that the emissive layer was transferred well without the separation of the host and the dopant owing to a difference in their evaporation temperatures. Consequently, its efficiency suffered a minor decline owing to the oxidation of the material caused by the poor vacuum pressure of the process chamber; however, it exhibited an identical color property.

• Textile Coloration and Finishing
• /
• v.28 no.3
• /
• pp.208-218
• /
• 2016

This study investigated the effects of the working mechanisms of proteins, mordants, and dyes, as well as the mordanting order, on dye uptake by silk fabric pre-treated with proteins and dyed with freeze-dried sappan wood water extract. Soybean protein and sodium caseinate were used as the proteins. 1. When Al mordants were not used, the dyeability of the fabrics increased upon protein pre-treatment as compared to the case without treatment. 2. Dyeing with protein pre-treatment, followed by mordanting, led to the highest dye uptake, and the optimal protein concentration was 5%. 3. The K/S values slightly decreased with an increase in the dyeing temperature, and the fabric turned dark red in color when dyeing was carried out at increasing temperature. Fabrics showed the highest dye uptake at $40^{\circ}C$. 4. Regarding the effect of time, the K/S values of the fabrics with and without protein treatment showed almost no increase after the initial dyeing time of 10min; further, there was hardly any difference in the cases with and without protein pre-treatment. 5. In case of protein pre-treatment fabrics, the washing fastness was level 2. The dry cleaning fastness showed very excellent result with level 4-5. The rubbing fastness was better in dry rubbing than in wet rubbing of the fabrics. For the light fastness, all dyed fabrics showed low fastness.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.6
• /
• pp.463-470
• /
• 2022

Intravenous injection is widely used for patient treatment, including injection drugs, fluids, parenteral nutrition, and blood products, and is the most frequently performed invasive treatment for inpatients, including blood collection, peripheral catheter insertion, and other IV therapy, and more than 1 billion cases per year. Intravenous injection is one of the difficult procedures performed only by experienced nurses who have been trained in intravenous injection, and failure can lead to thrombosis and hematoma or nerve damage to the vein. Nurses who frequently perform intravenous injections may also make mistakes because it is not easy to detect veins due to factors such as obesity, skin color, and age. Accordingly, studies on auxiliary equipment capable of visualizing the venous structure of the back of the hand or arm have been published to reduce mistakes during intravenous injection. This paper is about the development of venous detection equipment that visualizes venous structure during intravenous injection, and the optimal combination was selected by comparing the brightness of acquired images according to the combination of near-infrared (NIR) LED and Filter with different wavelength bands. In addition, an image processing algorithm was derived to threshehold and making blood vessel part to green through grayscale conversion, histogram equilzation, and sharpening filters for clarity of vein images obtained through the implemented venous detection experimental module.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.4-4
• /
• 2008

The progress in flat panel displays over the last two decades has been astonishing. In just 20 years, the LCD-TV grew up from a 2-inch curiosity, to an industry that will sell about 120 million flat panel TV's this year, with viewing area up to 4000 times larger. That success is based on continuous innovation, especially in manufacturing processes. For the next decade to bring another doubling of the business, progress will need to continue in four major areas: Human factors, ecological impact, visual quality, and of course continued drive towards affordability. This talk will detail the technology advances that can allow this industry to meet those challenges. Human factors. Today, we adapt our lifestyle to our technology. People organize their offices, and their homes, around displays. We pass around mobile phones to share images, rather than experiencing them as a group. Billions of newspapers continue to be sold daily. Advances in flexible displays can lead to large portable displays. "New era projection" includes the handheld Pico Projectors that are already on the market, and will ultimately appear integrated in mobile phones the same way cameras do today. "Eco" impact. Today TV's are one of the top energy consumers in a U.S. home, and the fastest growing. Watching a large flat panel TV can cost twice as much as running a large refrigerator. With today's concern about energy consumption, regulations are starting to emerge worldwide to limit TV electrical use. Fortunately, good solutions exist in using light management films to eliminate bulbs, saving power without increasing cost. Going forward, LED backlights will drive another step downward. OLED displays might be the ultimate solution. Visual quality. The color of an LCD-TV is still often considered inferior to a far less expensive CRT. And almost all displays suffer from representing a three-dimensional world on a two dimensional surface. The technology to improve color is available today, and will likely move from premium sets into the mainstream as costs come down. 3D is now arriving in movie theaters worldwide, and that will drive up the demand for similar realistic images in home theaters. And the technology is emerging today for 3D representation to move beyond specialized applications into everyday use, on screens large and small. Affordability. The world takes cost-down miracles for granted in consumer electronics. Each of these other advances will be balanced with a drive for affordability, especially as the market grows in emerging countries. The other three challenges must be met without increasing cost. Putting this all together, the next few years will emphasize "eco friendly" designs, and enhanced images such as 3D. By 2013 we will start to see serious penetration by emissive technologies (OLED, high efficiency plasma, or other), with the "ultimate display" likely not in the market for a decade. Lots of opportunities for innovation remain ahead of us.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.327-327
• /
• 2009

ZnO with a large band gap (~3.37 eV) and exciton binding energy (~60 meV), is suitable for optoelectronic applications such as ultraviolet (UV) light emitting diodes (LEDs) and detectors. However, the ZnO-based p-n homojunction is not readily available because it is difficult to fabricate reproducible p-type ZnO with high hall concentration and mobility. In order to solve this problem, there have been numerous attempts to develop p-n heterojunction LEDs with ZnO as the n-type layer. The n-ZnO/p-GaN heterostructure is a good candidate for ZnO-based heterojunction LEDs because of their similar physical properties and the reproducible availability of p-type GaN. Especially, the reduced lattice mismatch (~1.8 %) and similar crystal structure result in the advantage of acquiring high performance LED devices. In particular, a number of ZnO films show UV band-edge emission with visible deep-level emission, which is originated from point defects such as oxygen vacancy, oxygen interstitial, zinc interstitial[1]. Thus, defect-related peak positions can be controlled by variation of growth or annealing conditions. In this work, the undoped ZnO film was grown on the p-GaN:Mg film using RF magnetron sputtering method. The undoped ZnO/p-GaN:Mg heterojunctions were annealed in a horizontal tube furnace. The annealing process was performed at $800^{\circ}C$ during 30 to 90 min in air ambient to observe the variation of the defect states in the ZnO film. Photoluminescence measurements were performed in order to confirm the deep-level position of the ZnO film. As a result, the deep-level emission showed orange-red color in the as-deposited film, while the defect-related peak positions of annealed films were shifted to greenish side as increasing annealing time. Furthermore, the electrical resistivity of the ZnO film was decreased after annealing process. The I-V characteristic of the LEDs showed nonlinear and rectifying behavior. The room-temperature electroluminescence (EL) was observed under forward bias. The EL showed a weak white and strong yellowish emission colors (~575 nm) in the undoped ZnO/p-GaN:Mg heterojunctions before and after annealing process, respectively.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2008.05a
• /
• pp.47-70
• /
• 2008

Cost efficiency is today the primary requirement in the paper and board industry. This has led therefore, to a greater preponderance of products with specifically designed functionality to take account of current industry needs. Continually increasing machine coating speeds together with these new coating colour components have put more emphasis on the importance of the correct rheology and water retention of the coating colours to achieve good runnability and end product quality. In the coating process, some penetration of the aqueous phase, to the base paper or board must occur to anchor the pre-coating to the base or the topcoat to the pre-coat. The aqueous phase acts as a vehicle not only for the binder, but also for the other components. If this water or material penetration is not controlled, there will be excessive material shift from the coating colour to the base, before immobilization of the coating colour will stop this migration. This can result in poor machine runnability, unstable system and uneven coating layer, impacting print quality. The performance of rheology modifiers or thickeners on the coating color have tended to be evaluated by the term, "water retention". This simple term is not sufficient to explain their performance changes during coating. In this paper we are introducing a new concept of "material retention", which takes note of the total composition of the coating colour material and therefore goes beyond the concept of only water retention. Controlled material retention leads to a more uniform z-directional distribution of coating colour components. The changes that can be made to z-directional uniformity will have positive effects on print quality as measured by surface strength, ink setting properties, print gloss, mottling tendency. Optical properties, such as light scattering, whiteness and light fastness delivery should also be improved. Additionally, controlled material retention minimizes changes to the coating colour with time in re-circulation giving less fluctuation in quality in the machine direction since it more closely resembles fresh coating for longer periods. Use of the material retention concept enables paper and board producers to have more stable runnability (i.e. lower process costs), improved end product quality (i.e. better performance of used chemicals) and/or optimized use of coating colour components (i.e. lower total formulation cost)