• Proceedings of the Materials Research Society of Korea Conference
• /
• 2008.11a
• /
• pp.21.1-21.1
• /
• 2008

• Journal of Marine Bioscience and Biotechnology
• /
• v.8 no.1
• /
• pp.24-29
• /
• 2016

Microalgae are considered as superior biodiesel producers, because they could effectively produce high amount of lipid with fast growth rate. In this study, Chlorella vulgaris was exposed to various light wavelengths (${\lambda}_{max}$ 470 nm, ${\lambda}_{max}$ 525 nm, and ${\lambda}_{max}$ 660 nm) using light emitting diodes (LEDs) to examine effect of light quality on their growth and fatty acid production in 0.4-L bubble column photobioreactors. Fluorescent lamps were also used as polychromatic light sources (control). From the results, biomass productivity was varied by light wavelength from 0.05 g/L/day to 0.30 g/L/day. Maximum biomass productivity was obtained from red LED among tested ones. We also observed that contents of oleic acid and linolenic acid, which affect biodiesel properties, were significantly changed depending on supplied wavelength. These results indicated that production of algal biomass, and fatty acid content and productivity could be improved or controlled by supplying specific light wavelength.

• Journal of Biomedical Engineering Research
• /
• v.35 no.5
• /
• pp.125-131
• /
• 2014

The purpose of this study is to verify the utility of reflected photoplethysmography sensor using two green light emitting diodes that influenced by ambient light. Recently it has been studied that green light emitting diode is suitable for light source of reflected photoplethysmography sensor at low temperature and high temperature. Another study showed that, green light is better for monitoring heart rate during motion than led light. However, it has a bad characteristic about ambient light noise. To verify the utility of reflected photoplethysmography sensor using green light emitting diode, this study measures the photoplethysmography signal that is distorted by ambient light and will propose a solution. This study has two parts of research method. One is measurement system that composed sensor and board. The sensor is made up PE-foam and Non-woven fabric for flexible sensor. The photoplethysmography signal is measured by measurement board that composed high-pass filter, low-pass filter and amplifier. Ambient light source is light bulb and white light emitting diode that has three steps brightness. Photoplethysmography signal is measured with lead II electrocardiography signal at the same time and it is measured at the finger and radial artery for 1 minute, 1000 Hz sampling rate. The lead II electrocardiography signal is a standard signal for heart rate and photoplethysmography signal that measured at the finger is a standard signal for waveform. The test is repeated 3 times using three sensor. The data is processed by MATLAB to verify the utility by comparing the correlation coefficient score and heart rate. The photoplethysmography sensor using two green light emitting diodes is shown better utility than using one green light emitting diode and red light emitting diode at the ambient light. The waveform and heart rate that measured by two green light emitting diodes are more identical than others. The amount of electricity used is less than red light emitting diode and error peak detectability factor is the lowest.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.4
• /
• pp.548-561
• /
• 2020

Paecilomyces japonica is widely cultured to produce mycelium for medicinal and health food use. Illumination is an important factor in the growth and production of mycelium in submerged culture. The effects of different light-emitting diode (LED) combinations on the growth and cordycepin content as bioactive substances of mycelium were investigated. The results showed that the mycelium dry weights were lower under dark condition and red LED treatments. Dark condition, fluorescent light, and ultraviolet-A failed to increase the cordycepin content. Blue light was necessary to increase the cordycepin content, and a red-to-blue ratio of 3:7 induced the highest cordycepin content. The cordycepin contents of mycelium in submerged culture were significantly higher in a 12 h/day illumination time under red and blue (red-to-blue ratio of 3:7) LED treatments, showing an increase of up to 38% compared with those under the fluorescent-light control condition. The results demonstrated the roles of light with different wavelengths on the biosynthesis of cordycepin as bioactive substances. The low-heat release and replacement of traditional fluorescent lights with low-energy-consuming LEDs could increase the contents of bioactive substances. After optimization of the cordycepin production using response surface methodology (Box-Behnken design) to its canonical form, the optimum combination was found to be as follows: illumination time = 17.7 h/day, sugar content in the medium = 9.7 g/50 mL, and incubation time = 61.2 h. The model predicted a maximum response of 3779.2 ㎍/mL cordycepin yield.

• Journal of the Korean Chemical Society
• /
• v.45 no.2
• /
• pp.156-161
• /
• 2001

Various oxidation states of Polyaniline(PANI) were chemically synthesized, and characterized by FT-IR, UV-Vis, GPC, TG-DTA, Single layer light emitting diodes(LED) were perpared by spin coating of LEB-PANI solutions which have various oxidation states onto an ITO substrate and subsequent vacuum deposition of aluminum top electrode and then current-voltage characteristics. EL spectrum was investigated It was found that ${\pi}$-${\pi}$* transition were shifled to longer wavelength and molecular excition transition were decreased in the UV-Vis spectra and the intensity of EL and PL were increased as the contents of fully reduced form LEB increased. The turn-on voltage of ITO/LEB/AI structured LED was 5 V. It was found that the white light was emitted only from the phase with reduced epeat unit.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.97-98
• /
• 2008

n-ZnO/p-Si heterostructure is a good candidate for ZnO-based heterojunction light emitting diodes(LED) because of its competitive price and lower driving voltage. However, the conventional LED shows much lower extraction efficiency, because it has small top contact and large backside contact. In this structure, the injected current from the top contact enters the active region underneath the top contact. Thus, the emitted light is hindered by the opaque top contact. This problem can be solved by using a current-blocking layer(CBL) that prevents the current injection into the active region below the top contact.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.41 no.6
• /
• pp.511-517
• /
• 2008

The radiation characteristics and economic efficiency of high - luminance light - emitting diodes (LEDs), a metal halide lamp, and a halogen lamp were studied to evaluate their potential as an energy-saving light source for fishing lamps. The wavelengths at which irradiance was maximum were 709, 613, 473, 501, 525, 465, 578, and 973 nm for red, orange, blue, peacock blue, green, and white LEDs, the metal halide lamp, and the halogen lamp, respectively. If the irradiance characteristics at 300-1,100 nm wavelengths are set as 100%, the irradiance rates at 381-780 nm were 99-78%, 82%, and 24% for the LEDs, metal halide lamp, and halogen lamp, respectively. The economic efficiency was superior in the order metal halide lamp, halogen lamp, peacock blue LED, and blue LED at 381-780 nm and metal halide lamp, peacock blue LED, blue LED, and halogen lamp at 480-520 nm. Based on the radiation characteristics and economic efficiency evaluated at 480-520 nm, the blue and peacock blue LED light sources can be used as energy-saving light sources for fishing lamps.

• Korean Journal of Optics and Photonics
• /
• v.25 no.5
• /
• pp.254-261
• /
• 2014

Two types of white light-emitting diodes (LEDs) with different phosphor structures were fabricated and compared in terms of their optical characteristics. Their spectroscopic properties were analyzed as a function of temperature, from room temperature to $80^{\circ}C$. The temperature dependence of the luminance and the color coordinates showed that the decrease in luminance and change in the color coordinates of the remote-phosphor type LED were much smaller compared to the conventional white LED. These improvements were attributed to the decrease in phosphor temperature, due to the distance between the LED chip and the phosphor layer, as well as to the reduced absorption by the LED chip of the light emitted from the phosphor layer.

• Journal of Ceramic Processing Research
• /
• v.13 no.spc1
• /
• pp.75-77
• /
• 2012

The AlGaN-based vertical light-emitting diodes (LEDs) on thick GaN epilayer were fabricated by a hydride vapor phase epitaxy with multi sliding boat system. The optical and electrical characteristics of AlGaN-based vertical LEDs were evaluated using a scanning electron microscopy, electroluminescence and I-V measurements. The AlGaN-based vertical LEDs structure has hexagonal symmetry, 500 ㎛ in diameter and above 67 ㎛ in growth thickness. At the room-temperature, the broaded strong peak and relatively high intensity peak were gradually measured at 405 nm with increasing injection current. And a forward operator voltage was measured to be about 7.5 V.

• The korean journal of orthodontics
• /
• v.46 no.6
• /
• pp.364-371
• /
• 2016

Objective: With the introduction of third-generation light-emitting diodes (LEDs) in dental practice, it is necessary to compare their bracket-bonding effects, safety, and efficacy with those of the second-generation units. Methods: In this study, 80 extracted human premolars were randomly divided into eight groups of 10 samples each. Metal or polycrystalline ceramic brackets were bonded on the teeth using second- or third-generation LED light-curing units (LCUs), according to the manufacturers' instructions. The shear bond strengths were measured using the universal testing machine, and the adhesive remnant index (ARI) was scored by assessing the residual resin on the surfaces of debonded teeth using a scanning electron microscope. In addition, curing times were also measured. Results: The shear bond strengths in all experimental groups were higher than the acceptable clinical shear bond strengths, regardless of the curing unit used. In both LED LCU groups, all ceramic bracket groups showed significantly higher shear bond strengths than did the metal bracket groups except the plasma emulation group which showed no significant difference. When comparing units within the same bracket type, no differences in shear bond strength were observed between the second- and third-generation unit groups. Additionally, no significant differences were observed among the groups for the ARI. Conclusions: The bracket-bonding effects and ARIs of second- and third-generation LED LCUs showed few differences, and most were without statistical significance; however, the curing time was shorter for the second-generation unit.