• Journal of Information Display
• /
• v.11 no.2
• /
• pp.39-44
• /
• 2010

The time dependences of the luminance properties of 55-inch CCFL and LED backlights and 32-inch FFL backlights with LCD panels were investigated during the warm-up time from the cold start. The long-term luminance maintenance curve of a standard CCFL was examined in a time window up to 5000 hours. These two time dependences are important characteristics from the viewpoint of initial picture quality and lifetime reliability, respectively. Empirical equations were suggested for the analysis of the time dependence of these luminance data. These approaches are expected to be helpful in predicting the luminance properties of backlights based on the luminance data obtained in a limited time window.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1211-1213
• /
• 2004

CCFL(cold cathode fluorescent lamp) are used to backlight of LCD(liquid crystal display). CCFL dimming methods are used to pulse frequency modulation(PFM) or pulse width modulation(PWM). In this paper, design of CCFL driving and control circuit by half-bridge type series and parallel resonant inverter that variable frequency modulation method to control the output voltage current. Inverter switching frequency is higher than resonant frequency for stable operating, and it is possible dimming control. On the basis of equivalent circuit, the validity of this study is confirmed by the comparison of simulation and experimental result.

• Journal of Information Display
• /
• v.10 no.1
• /
• pp.28-32
• /
• 2009

The correlation between the optical performance of the reflective polarizer, which is a key optical component for the brightness enhancement of the liquid crystal display (LCD), and the configuration of optical sheets was investigated in a direct-lit CCFL (cold-cathode fluorescent lamp) backlight. The optical gain of the reflective polarizer, the polarization state of the light emitted from each film, and the loss factor for the polarization conversion process occurring in the lower part of the backlight were determined using a phenomenological approach for the polarization recycling process. The present study suggests that the correlation between the optical performance of the brightness enhancement films and the backlight configuration should be carefully considered in the optimization of the backlight structure.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.1
• /
• pp.61-65
• /
• 2011

Recently, LCD (liquid crystal display) industry is needed to goods of high reliability and wide range temperature condition and it is interested in products for extremely cold condition without failure of light-up. In this experiment, we made the LED backlight unit for Automotive-navigation under the extremely cold condition. And for making this backlight unit, we used to eight side emitting type white LEDs with 3W high power LED. We could know that this backlight unit releases to 18,000 nit in 24W power consumption and start up voltage time is under the 1ms in the ambient temperature at -40.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.146-149
• /
• 2005

In applying LCD to TV application, one of the most significant factors to be improved is image sticking on the moving picture. LCD is different from CRT in the sense that it's continuous passive device, whichholds images in entire frame period, while impulsetype device generate image in very short time. We realized articulate image generation similar to CRT by CCFL blinking drive and TN-LCD overdriving. As a result, reduced image sticking phenomenon was validated by naked eye and response time measureme.

• Korean Journal of Materials Research
• /
• v.19 no.1
• /
• pp.7-12
• /
• 2009

TFT-LCD is the most popular type of flat display panel in the information technology field. The back light unit is a main part of the structure of a TFT-LCD panel. Occasionally, studies have shown that failures of the CCFL of the BLU occur due to the poor weld characteristics of these materials. The aim of this study was to prepare some technical data and to characterize a microjoined electrode for the CCFL. Microstructure examinations, microhardness measurements, resistance measurements and microtensile tests of the microjoined electrode were carried out. The result indicates that a large amount of grain coarsening exists in the heat-affected zone (HAZ) of the weld between the cup and the pin. This grain coarsening of the HAZ between the cup and pin is caused by the welding cycle, which may have an influence on the lowest microhardness values. Fracturing of the microjoined electrode also occurred at the HAZ close to the cup between the weld holding the cup and the pin. Additionally, no specific changes of the electrical resistance among the cup, pin, and lead wire themselves or in the microjoined electrode were observed.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.746-749
• /
• 2005

LCD 디스플레이의 대형화에 따라 백라이트용 냉음극 방전램프(Cold Cathode Fluorescent Lamp)는 길어지고 있으며, 하나의 램프를 이용한 백라이트는 휘도의 한계가 있어 대형 디스플레이에서는 램프를 병렬로 사용하여 필요한 휘도를 만들고 있다. 본 논문에서는 냉음극 방전램프 16개를 사용하는 37인치 LCD TV용 대형 백라이트 구동을 위한 인버터를 각각의 램프들이 입력조건에 대해 동일한 출력을 갖도록 설계하였다. 기존의 냉음극 방전램프의 구동방식인 하이-로우(H-L) 방식에서의 문제점을 보완하여 하이-하이(H-H) 방식을 채택하므로서 램프간의 휘도편차를 개선하였고 향후에 상용화가 가능함을 보였다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1058-1061
• /
• 2004

Recently, According to companies of TFT LCD are making large sized products more and more. In the vortex of Products with a monitor and LCD TV is applied in a technique of a high viewing angle(FFS, IPS, VA). Also, as a high luminance, high speed response time, high degree of a color purity, and so on are continuing to develop a high performance, it is necessary to improve a specific character of high luminance that apply to LCD TV as a LCD BLU. Because a LCD panel for TV usually has a lower resolution that compare to a monitor, the structure of present backlight system can't put out its power even though it has a merit in transmission. Therefore, the examination of improvement about the high luminance direct typed BLU for LCD TV that presupposes several uses of CCFL(Cold Cathode Fluorescent Lamp) or EEFL(External Electrode Fluorescent Lamp)is actively being progressed. Although it is necessary to increase the number of lamps for applying high performance by the direct type, in this case, because we can design the character of luminance for adoption of high performance. We can satisfy with a level of luminance for LCD TV. Accordingly, we analyzed a change of the number of CCFL, mechanical and optical character to produce the direct typed backlight in 32inches spec. Consequently, we achieved luminance of 6597nit,which was including polarization film, and secured the standard for LCD TV.

• 한국정보통신설비학회:학술대회논문집
• /
• 2009.08a
• /
• pp.86-87
• /
• 2009

LED backlight for LCD TV is a great alternative to CCFL backlight due to its low power consumption and flexible arrangement. Various LED backlight configurations are being used to control the backlight locally in order to achieve both power efficiency and high contrast. However, the relatively small spatial resolution of the backlight system results in showing artifacts of backlight control that is acknowledgeable to human vision. Moreover, such artifacts get worse between temporal frames. In this paper we present a method of decreasing such temporal artifacts with a Human Visual System(HVS) approach to minimize distortion caused by local backlight dimming.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.5
• /
• pp.215-217
• /
• 2007

Recently, color reproduction properties have attracted lots of attention with mass production of LCD especially corresponding to TV application and achievement of color reproduction properties such as CRT have been considered one of technical goals for high quality display. However, revision of the color reproduction properties only with CF(color filter) have fundamental limitations and resultant decrease in the transmittance of panel causes demand on high brightness of BL(Back Light). In this paper, we present such a method in which by optimization of original light spectrum from the BL source will improves the color reproduction properties corresponding to them of the CRT. When the intensity of RED and Green-Blue from ramp is revised densely, the characteristics different from CCFL(Cold Cathode Fluorescent Lamp) used before become added so that about 11 % of the color reproduction properties is improved compare to the existing LCD panel.