• 전력전자학회논문지
• /
• 제15권2호
• /
• pp.150-158
• /
• 2010

본 논문은 입력단 전압과 출력단 부하전압의 상대적 크기에 따라 동작모드가 다르게 구성되며, 열전에너지 수확이 가능한 새로운 공진형 DC/DC 컨버터의 동작 특성을 해석한다. 공진형 DC/DC 컨버터는, 직류 입력전원에 연결 되는 LC 공진회로와, 공진회로의 캐패시터 전압이 최대일 때 부하측으로 에너지를 전달하는 펄스형 공진 컨버터로 구성되어있다. 입력단 LC 공진회로의 캐패시터는 전압의 최대값이 입력전압의 최대값의 2배가 되는 Voltage Doubler의 특성을 갖는다. 제안한 컨버터는 공진 캐패시터 전압의 최대값과 부하전압의 상대적 크기에 따라서 승압형 연결, 혼합형 연결, 직접연결의 3가지 동작특성을 가진다. 승압형 연결은 공진 캐패시터 전압의 최대값이 부하전압보다 작은 경우이다. 혼합형 연결은 공진 캐패시터 전압의 최대값이 부하전압보다 큰 경우이며, 스위칭 주기에 직접연결과 승압형 연결이 연속하여 나타난다. 직접연결은 입력단 전압의 크기가 부하전압보다 큰 경우이며, 입력단 에너지가 부하측으로 컨버터의 스위칭 동작 없이 직접 전달된다. 공진형 DC/DC 컨버터 회로의 동작원리를 설명하고, PSPICE 시뮬레이션 및 실험을 통하여 검증하였으며, 열전에너지 수확분야에 활용 가능성을 제시하였다.

• 대한전자공학회논문지SD
• /
• 제46권6호
• /
• pp.16-24
• /
• 2009

본 논문에서는 인덕터와 커패시터를 집적화한 DC-DC 벅 변환기를 설계하였다. 출력전압의 리플크기를 줄이기 위해 stacked interleaved 방식을 이용하였고 변환기의 제어부는 전압모드 방식의 제어방법을 사용하여 설계하였다. 설계한 DC-DC 벅 변환기는 표준 $0.5{\mu}m$ CMOS 공정으로 제작 중이며 전체면적은 $9mm^2$이다. 설계된 회로는 $3V{\sim}5V$의 입력전압에서 동작하며 LC 필터의 크기를 줄이기 위해 50MHz의 주파수로 동작하였다. 최대 250mA의 부하전류 구동이 가능하며 최대 71%의 전력변환 효율을 가졌다.

• 전기학회논문지
• /
• 제64권11호
• /
• pp.1543-1550
• /
• 2015

Ferroresonance is a non-linear vibrational phenomenon that is generated by the electrical interaction of the inductance component with the capacitor component of a certain capacitance as the device of the inductance component such as a transformer is saturated due to the degradation, the waveform distortion of current and voltage, and the oscillation of overcurrent and overvoltage in a system. Recently, ferroresonance was generated from the waveform distortion of current and voltage, or the overvoltage or undervoltage phenomenon caused by the nature of an electrical power system and design technology of the transformer in the three phase transformer system. Hence, in general, ferroresonance analyzed by converting to the LC equivalent circuit. However, in general, the aforementioned analytical method only applies to the resonance phenomenon that is generated by the interaction of the capacitance of bussbar and grounding, and switching as the capacitor component with PT and the transformer as the inductance component in a system. Subsequently, the condition where ferroresonance was generated since overvoltage was supplied as line voltage to the phase voltage and thus the iron core is saturated due to the interconnection between grounded and ungrounded systems could not be analyzed when single phase PT was connected in a ${\Delta}$/Y connection system. In this study, voltage swell in the configuration of grounded circuit of a step-up transformer with the ${\Delta}-{\Delta}$ connection linked to PT for control power and the ferroresonance generated by overvoltage when the line voltage of the ${\Delta}-{\Delta}$ connection was connected to the phase voltage of the grounded Y-Y connection were analyzed using PSCAD / EMTDC through the failure case of the transformer caused by ferroresonance in the system with the ${\Delta}-{\Delta}$/Y-Y connection, and subsequently, the preventive measure of ferroresonance was proposed.

• Transactions on Electrical and Electronic Materials
• /
• 제12권6호
• /
• pp.262-266
• /
• 2011

A simulation study of a current-mode direct current (DC)-DC boost converter is presented in this paper. This converter, with a fully-integrated power module, is implemented by using bipolar complementary metal-oxide semiconductor (BiCMOS) technology. The current-sensing circuit has an op-amp to achieve high accuracy. With the sense metal-oxide semiconductor field-effect transistor (MOSFET) in the current sensor, the sensed inductor current with the internal ramp signal can be used for feedback control. In addition, BiCMOS technology is applied to the converter, for accurate current sensing and low power consumption. The DC-DC converter is designed with a standard 0.35 ${\mu}m$ BiCMOS process. The off-chip inductor-capacitor (LC) filter is operated with an inductance of 1 mH and a capacitance of 12.5 nF. Simulation results show the high performance of the current-sensing circuit and the validity of the BiCMOS converter. The output voltage is found to be 4.1 V with a ripple ratio of 1.5% at the duty ratio of 0.3. The sensing current is measured to be within 1 mA and follows to fit the order of the aspect ratio, between sensing and power FET.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2007년도 추계학술대회 논문집
• /
• pp.337-340
• /
• 2007

In the dissertation, a power conversion system for fuel cell is composed of a PWM inverter with LC filter in order to convert fuel cell voltage to a single phase 220[V], In addition, new insulated DC-DC converters are proposed in order that fuel cell voltage is boosted to 380[V]. In this paper, it requires smaller components than existing converters, which makes easy control. The proposed DC-DC converter controls output power by the adjustment of phase-shift width using switch S5 and S6 in the secondary switch, which provides 93-97[%] efficiency in the wide range of output voltage. Fuel cell simulator is implemented to show similar output characteristics to actual fuel cell. Appropriate dead time td enables soft switching to the range where the peak value of excitation current in a high frequency transformer is in accordance with current in the primary circuit. Moreover, appropriate setting to serial inductance La reduces communication loss arisen at light-load generator and serge voltage arisen at a secondary switch and serial diode. Finally, TMS320C31 board and EPLD using PWM switching technique to act a single phase full-bridge inverter which is planed to make alternating current suitable for household.

• Journal of Power Electronics
• /
• 제14권2호
• /
• pp.226-236
• /
• 2014

A new active LED driver with high power factor (PF) and low total harmonic distortion (THD) compatible with a rapid-start ballast is proposed. An LC input filter is attached to the ballast to increase PF and reduce THD. A boost converter is then installed to regulate the LED current, where an unstable operating region has been newly identified. The unstable region is successfully stabilized by feedback control with two zeroes. The extremely high overall system of the 10th order is completely analyzed by the newly introduced phasor transformed circuits in static and dynamic analyses. Although a small DC capacitor is utilized, the flicker percentage of the LED is drastically mitigated to 1% by the fast controller. The proposed LED driver that employs a simple controller with a start-up circuit is verified by extensive experiments whose results are in good agreement with the design.

• Journal of Electrical Engineering and Technology
• /
• 제13권6호
• /
• pp.2441-2446
• /
• 2018

This paper presents a radio frequency-to-direct current (RF-to-DC) converter for special RF power harvesting application at 915 MHz. The major featured components of the proposed RF-to-DC converter is the combination of a cross-coupled rectifier and an active diode: first, the cross-coupled rectifier boosts the input voltage to desired level, and an active diode blocks the reverse current, respectively. A prototype was implemented using $0.18{\mu}m$ CMOS technology, and the performance was proven from the fact that the targeted RF harvesting system's full-operation with higher power efficiency; even if the system's input power gets lower (e.g., from nominal 0 to min. -12 dBm), the proposed RF-to-DC converter constantly provides 1.47 V, which is exactly the voltage level to drive follow up system components like DC-to-DC converter and so on. And, maximum power conversion efficiency is 82 % calculated from the 0 dBm input power, 2.3 mA load current.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.295-298
• /
• 2003

Reflective mode liquid crystal on silicon (LCoS) microdisplay is the major technology that can produce extremely high-resolution displays. A very large number of pixels can be packed onto the CMOS circuit with integrated drivers that can be projected to any size screen. Large size direct-view thin film transistor (TFT) LCDs becomes very difficult to make and to drive as the information content increases. However, the existing LC alignment technology for the LCoS cell fabrication is still the mechanical rubbing method, which is prone to have minor defects that are not visible normally but can be detrimental if projected to a large screen. In this paper, application of photo-alignment to LCoS fabrication is presented. The alignment is done by three-step exposure process. A MTN $90^{\circ}$ mode is chose as to evaluate the performance of this technique. The comparison with rubbing mode shows the performance of photo-alignment is comparable and even better in some aspect, such as sharper RVC curve and higher contrast ratio.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2000년도 종합학술발표회 논문집 Vol.10 No.1
• /
• pp.150-153
• /
• 2000

In this paper, we have designed a 2 stage MMIC power amplifier which has flat gains of in-band and reasonable out-band cutoff characteristics using 0.5$\mu\textrm{m}$ MESFET libra교 of ETRI. For the 1st stave, we obtaind P$_{1dB}$ of 9.2 dBm and gain 10.8 dB using 6 finger D-MESFET and P$_{1dB}$ of 18.4 dBm and gain of 10.8 dB using 14 finger D-MESFET for the 2nd stage, which is power matched using LIBRA's embedded TUNER. Also in-band gain flatness and out-band cutoff characteristics are obtained by attaching LC tank in the output matching circuit. The designed 2 stage MMIC power amplifier has bandwidth of 0.95～2.8 GHz, gain of 20 dB and P$_{1dB}$of 17.2 dBm. Especially gain flatness of $\pm$0.8dB was obtained in 1.8～2.5 GHz frequency ranges. And chip size is 1.4$\times$1.4 mm..4 mm.

• 천문학회보
• /
• 제37권1호
• /
• pp.66.1-66.1
• /
• 2012

We have developed superconducting mixer receivers for 129 GHz VLBI observation in Korean VLBI Network(KVN). The developed mixer has a radial waveguide probe with simple transmission line LC transformer as a tuning circuit to its 5 series-connected junctions, which can have 125-165 GHz as operation RF frequency. For IF signal path a high impedance quarter-wavelength line connects the probe to one end of symmetric RF chokes. DSB receiver noise of the mixer was about 40 K over 4-6 GHz IF band whereas we achieved about uncorrected SSB noise temperature of 70 K and better than 10 dB IRR in 2SB configuration with 8-10 GHz IF band. Insert-type receiver cartridges using the mixers have been assembled for all three KVN stations. On-site performance summary in commissioning phase is presented.