• International Journal of Highway Engineering
• /
• v.19 no.2
• /
• pp.17-24
• /
• 2017

PURPOSES : This study aims to develop a sealant for use in the installation of Weigh-In-Motion (WIM) sensor for asphalt concrete or cement concrete pavements. METHODS : In order to investigate the properties of various sealants that were mixed with latex and carbon fiber, various test methods were adopted, such as bituminous bond strength test, softening point test, and cone penetration test. To evaluate moisture susceptibility, the BBS test was conducted under moist condition. The bond strength ratio (BSR) was calculated based on tensile strength ratio method. RESULTS : The sealant's properties significantly varied according to the amount of latex or carbon fiber. The usage of latex marginally enhanced the cone penetration test result, notwithstanding reduced asphalt content. This implies that the sealant will be proper cold temperature reason. Moreover, the addition of latex and carbon fiber evidently increased the softening point. This indicates that the tendency of the material to flow at elevated temperatures is encountered during service. With the addition of latex and carbon fiber, the moisture susceptibility measured with BSR improved marginally, while the bond strength under dry condition decreased marginally. Sealant F displays the highest bond strength and BSR under limited test conditions. CONCLUSIONS : According to the proportion of latex and carbon fiber mixed, properties of sealant, such as softening point, cone penetration, and BSR varied marginally. This indicates that the sealant has to be applied considering the environmental condition, to improve service life.

• Parasites, Hosts and Diseases
• /
• v.27 no.3
• /
• pp.171-176
• /
• 1989

Total 2,829 persons consisted of 1,019 general patients and 1,030 asthma- suspected patients who visited Kangnam 51. Mary's Hospital and 780 general patients who visited Cheju Medical Center were examined for the antibody titers of Toxo- plasma by indirect latex agglutination(ILA) test. Nineteen out of 1,019(1.86%) cases in general patients group, 11 out of 1,030 (1.07%) cases in asthma patients group, and 45 out of 780(5.77%) cases in Cheju patients group showed positive ILA titers. Concerned with the age and ILA positive cases, general and asthma patients ex- pressed more cases at thirties to sixties while Cheju patients showed high incidence at children and adolescents in addition to the above mentioned ages. Frequencies of ILA positive titers were highest in 1 : 32 and 1 : 64, and some cases showed 1 : 2,048 or higher titers.

• Korean Journal of Food Science and Technology
• /
• v.29 no.3
• /
• pp.509-515
• /
• 1997

Crude papain was extracted from papaya latex under various conditions. Extraction conditions of crude papain were optimized by the response surface methodology (RSM). Extraction yield of papain was affected by concentration of $NaHSO_3$, extraction time and pH. Three independent factors were chosen to determine their effects on the various responses and the function was expressed in terms of a quadratic polynomial equation, which measures the linear, quadratic and interaction effects. According to the results of RSM, the stationary point for quantitatively dependent variable was found to be the maximum point for extraction yield. Optimum conditions of papain extraction were 4% of $NaHSO_3$, 120 min of extraction time and pH 7.6. Under these conditions, 793.16 mg of papain per g latex was extracted from papaya latex.

• Journal of the Korean Society of Physical Medicine
• /
• v.16 no.4
• /
• pp.117-124
• /
• 2021

PURPOSE: This study examined the effect of muscle thickness of the deep cervical flexor muscle, muscle tonicity, and muscle fatigue of the superficial cervical flexor muscle by applying a functional latex pillow to patients with chronic cervical pain. METHODS: An experimental group using a functional latex pillow and a control group using a general pillow were assigned randomly to 30 people. Each pillow was applied in a comfortable lying position in the experimental group and control group. The deep cervical flexor muscle thickness was measured in the longus colli and longus capitus using ultrasonography. The muscle tonicity and muscle fatigue of the superficial cervical flexor muscle were measured separately in the sternocleidomastoid muscle using a myotonometer and electromyography. RESULTS: In the experimental group(functional latex pillow), the muscle tonicity of the superficial cervical flexor muscle like the sternocleidomastoid muscle was significantly lower than that of the control group (general pillow)(p < .01). CONCLUSION: This study suggests that the functional latex pillow may effectively reduce the muscle tonicity of the sternocleidomastoid muscle, which is the superficial cervical muscle, in patients with chronic cervical pain. On the other hand, it was not effective on the muscle thickness of the deep cervical flexor muscle and muscle fatigue of the superficial cervical flexor muscles.

• Journal of Korean Society of Forest Science
• /
• v.46 no.1
• /
• pp.1-9
• /
• 1980

This study was carried out to examine the substitution possibility into fiber pot instead of Jiffy pot for the good transplanting. Fiber pot was made of fiber, wood waste particle, and bark powder (10% of the particle weight) and also latex was added into the furnish as a binder. The pots were sprayed with just enough urea solution to prevent nitrogen deficiency of pot media coming from the breakdown of wood fiber in the pot wan during the plant growing. The utility of fiber pot was compared with that of Jiffy pot in the service test of two tree species under a green-house condition. The results obtained can be summarized as follows ; 1. Fiber pot made of 30% wood fiber+70% particle including 10% of bark powder, and 3%-latex has shown a good results like that of Jiffy pot in the sp. gr., tear factor and burst factor. For water absorption, fiber pot made of 50% fiber+50% particle, and 3%-latex got the best result. In the consideration of the above physical and mechanical properties of the fiber pot for good root penetration through the pot wall and facile handling, fiber pot made of 30% fiber+70% particle, and 3%-latex may be seemed to be good. 2. There were no harms in sapling growth in fiber pot as well as in Jiffy pot. The root penetration ability through the fiber pot was slightly inferior to that of Jiffy pot, and yet the pot damage through transportation seemed to be slighter in fiber pot than in Jiffy pot.

• Korean Chemical Engineering Research
• /
• v.50 no.5
• /
• pp.789-794
• /
• 2012

For the purpose of development of the latex suitable for polymer cement mortar, experiments on the preparation of carboxylated styrene butadiene latex by the method of the two-step emulsion polymerization were performed. Methyl methacrylate, methacrylic acid and acrylic acid were selected as carboxylic co-monomer, styrene and butadiene as monomer, sodium dodecylbenzene sulfonate and sodium salt of lauryl sulfonate as anionic emulsifiers, and nonylphenoxy poly (ethyleneoxy) ethanol (n=10, 20, 40) as latex stabilizer. Potassium persulfate and sodium bisulfite were also used as redox initiator, and sodium monohydrogen phosphate and potassium carbonate as electrolytes. The effects of categories and concentration of carboxylic co-monomer, molecular weight control agent, crosslinking agent, and styrene/butadiene monomer ratio on the characteristics of latex were investigated. Polymerization recipes for preparation of polymer cement mortar could be proposed. The prepared latexes were tested for the physical properties such as compressive and flexural strength when latexes were mixed with cement mortar. The results showed that the latex could be adapted to polymer cement mortar. Also, it was recognized that the compressive and flexural strength were exhibited 25.4% and 45.3% respectively higher improvement than the quality standards at 28 days curing time.

• International Journal of Highway Engineering
• /
• v.4 no.2 s.12
• /
• pp.1-8
• /
• 2002

Latex modified concrete(LMC) became to be applied as a new material for newly constructed bridge deck overlays in Korea due to its excellent bond strength, flexural strength and impermeability against water and chloride. However, it could not be adopted at repair job site because of its long curing time required. Thus, a research on latex modified concrete with rapid-setting cement(RSLMC) is necessary if it could develope the sufficient strength for early opening to traffic. This study focused on the durability of latex modified concrete with rapid-setting cement mainly on water permeable resistance and freeze-thaw resistance. The main experimental variables were latex contents(0, 5, 10, 15 and 20%) and antifoamer contents (0, 1.6, 3.2, 4.8 and 6.4%). Test results show that the permeability of RSLMC is very low indicating below 100 coulombs at 15% of latex contents at all antifoamer contents. The freeze-thaw resistance of RSLMC maintains above 90% of relative dynamic modulus at 3.2% of antifoamer content until 300 freezing-thawing cycles.

• Pediatric Infection and Vaccine
• /
• v.13 no.2
• /
• pp.99-105
• /
• 2006

Purpose : The serotyping results of the Quellung reaction was compared with the newly developed multiplex latex assay and the sensitivity of the Quellung reaction was compared. Methods : We checked the serotypes of 35 samples obtained from patients treated at Yonsei University Medical Center using the multiplex latex bead method and compared the results with the serotypes previously obtained via the Quellung reaction. Results : A decrease in the mean fluorescence was detected in the samples tested with the multiplex assay. Seventeen samples out of the 27 samples agreed to the results of the Quellung assay. We were only able to confirm the concordance of 11 serotypes out of 14 serotypes available. Conclusion : The Quellung reaction is time consuming procedure and prone to errors even with expertise in the procedure, and other alternate methods in serotyping have been investigated to overcome these problems. The newly developed multiplex latex bead assay can test more samples at the same time and has a higher degree of sensitivity. A large scale trial is required to test the sensitivity of the new assay across various serotypes along with efforts to increase the sensitivity of the Quellung assay. The preliminary data suggests that this method may be widely used.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2011.10a
• /
• pp.39-41
• /
• 2011

The recycling rate of recovered paper in Korea is the highest in the world, 92%, but remanufacturing yield is low due to the extremely poor quality of the paper. The poor quality, in turn, influences to the reject amount in deinking process. To increase the yield of old newspaper recycling process, hydrophobic degree of inorganic pigments of deinking stock must be reduced. To determine the hydrophobicity, Pitch Potential Deposit Tester (PDT) was newly designed and applied with respect to the SB latex property of various quality used in Korea; its hydrophobic degree according to Tg, gel content, charge and particle size of latex and optimum designing condition of SB latex. And below are the conclusions: 1. The reason of excessive reject from old newspaper deinking process for total amount of printed ink is loss of inorganic pigments. When lipase, a biochemical catalyst, was applied with the purpose of preventing inorganic pigments loss about more than 70% of total reject weight and promoting hydration of pulp for deinking, deinking process yield of pre flotation secondary stage increased remarkably without any changes of deinking efficiency. 2. Lipase improved deinking stock by cutting ester linkage on surface of hydrophobic materials to promote its hydration. From this, it reached the conclusion that hydration degree of stock exercises significant effect on flotation deinking process yield. 3. Inorganic alkali promotes hydration of deinking stock. But there have been needs for more fundamental measures other than inorganic alkali of promoting hydration for yield improvement. For this, this study intended to find out reasons of chemical properties change on surface of hydrophobic material by change of pH. 4. Pitch Deposit Test (PDT) was performed for understanding principle of why surface of coating flake from OMG is hydrophobic and why it becomes hydrophilic when pH of stock is alkaline. As a result of this test, it is determined that swelling property by change of pH of latex film, which were used as coating adhesive is the reason for hydrophobic change. 5. Hydrophilicity of coating flake increased with hydrophilic pigments. And as more of SB Latex adhesive was used and higher of calcium hardness of stock became, its hydrophilicity decreased. SB Latex adhesive film is reformed by mechanical friction. For having hydrophilicity under neutral pH, strong bruising action such as kneading is required. 6. Because swelling of adhesive film decreases as Tg of SB latex gets lower and mean diameter gets smaller, it shows hydrophobicity under neutral pH. This lowers hydrophilicity of coating flake, which leads to easy elimination with flotation reject on DIP process. Therefore, for improving future flotation yield, it is necessary to develop to use eco-friendly clean SB latex by raising Tg and increasing mean diameter for recycling, and as a result, to reduce excessive loss of coating flake as a reject from deinking process.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.5
• /
• pp.18-38
• /
• 2002

A previous study on the model coatings based on latex-bound plastic pigment coatings (1) has been extended to latex-bound No. 1 clay, ultra-fine ground calcium carbonate (UFGCC), and clay-carbonate pigment mixture coatings, which are being widely used in the paper industry. The latex binder used was a good film-forming, monodisperse S/B latex or 0.15$\mu\textrm{m}$. No. 1 clay was representative of plate-like pigment particles, whereas UFGCC was of somewhat rounded rhombohedral pigment particlel. Both of them had negatively skewed triangular particle size distributions having the mean particle suet of 0.7${\mu}{\textrm}{m}$ and 0.6$\mu\textrm{m}$, respectively. Their packing volumes were found to be 62.5% and 657%, respectively. while their critical pigment volume concentrations (CPVC's) were determined to be 52.7% and 50.5% ( average of 45% caused by the incompatibility and 55.9% extrapolated) by coating porosity, respectively. Each pigment/latex coating system has shown its unique relationship between coating properties and pigment concentrations, especially above its CPVC. Notably, the clay/latex coating system hat shown higher coating porosity than the UFGCC/latex system at high pigment concentrations above their respective CPVC's. It was also found that their coating porosity and gloss were inter-related to each other above the CPVC's, as predicted by the theory. More interestingly, the blends of these two pigments have shown unique rheological and coating properties which may explain why such pigment blends are widely used in the industry. These findings have suggested that the unique structure of clay coatings and the unique high-shear rheology of ground calcium carbonate coatings can be judiciously combined to achieve superior coatings. Importantly, the low-shear viscosity of the blends was indicative of their unique packing and coating structure, whereas their high-shear rheology was represented by a common mixing rule, i.e., a viscosity-averaging. Transmission and scanning electron and atomic force microscopes were used to probe the state of pigment / latex dispersions, coating surfaces, freeze fractured coating cross-sections, and coating surface topography. These microscopic studies complemented the above observations. In addition, the ratio, R, of CPVC/(Pigment Packing Volume) has been proposed as a measure of the binder efficiency for a given pigment or pigment mixtures or as a measure of binder-pigment interactions. Also, a mathematical model has been proposed to estimate the packing volumes of clay and ground calcium carbonate pigments with their respective particle size distributions. As well known in the particle packing, the narrower the particle size distributions, the lower the packing volumes and the greater the coating porosity, regardless of particle shapes.