• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.18 no.1
• /
• pp.19-26
• /
• 2010

To expand the application area of global navigation satellite systems, precision landing is one of the most critical area to be solved. For the development and validation of the precision landing system, many aspects need to be analyzed including the system architecture, signal characteristics, atmospheric delay, communication delay, accuracy, integrity, and availability. Among them, the signal characteristics analysis requires the processing of measurements collected by real-flight experiments. This paper presents the processing results of the real measurements collected by a flight and landing experiment. To process and analyze the data, double differencing position-domain hatch filter is utilized. Accuracy of the proposed filter is evaluated utilizing reference trajectory generated by commercial software. Finally, by comparing with conventional range domain characteristics of position domain filter is analyzed.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.15 no.4
• /
• pp.33-37
• /
• 2007

In this paper, a dynamic analysis of a helicopter landing gear with considering flexible structural modes has been investigated. The main body of the helicopter has been modeled as a flexible body using FEM code, then a few selected vibration modes of the helicopter main body have been used as basis for the dynamic analysis of the helicopter landing gear. The simulation of dynamic analysis was carried out on the base of ADAMS aircraft module. It has been found by a series of simulation that the flexible structural modes has a significant effect on the dynamic characteristics of helicopter landing gear as the flexibility of the main body is increased.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.25 no.3
• /
• pp.61-67
• /
• 2017

The Nose Landing Gear(NLG) of Rotary Wing Aircraft is an essential equipment in Landing System for pilot to perform a flight mission. It supports the fuselage at ground and absorbs the impact from the ground when landing, thereby, these functions sustain operational capability for pilot and crew. However, the A aircraft caused stick-slip behavior when it was stationed on the ground. Therefore, this paper summarizes pilot comment in operation which are classified by cause of occurrence and the troubleshooting process about each comment. It also describes design improvements which was derived from troubleshooting and suggests verification results of flight test.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.8
• /
• pp.647-661
• /
• 2017

This paper presents a robust method for autonomously landing on small bodies. Autonomous landing is accomplished by generating and following reference position and attitude profiles. The position and attitude tracking controllers are based on discrete sliding mode control, which explicitly treats the discrete and impulsive natures of thruster operation. Vision-based inertial navigation is used for autonomous navigation for landing. Numerical simulation is carried out to evaluate the performance of the proposed method in a realistic situation with environmental uncertainties.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.363-366
• /
• 1996

A Reclaimer is used to dig raw material from a pile and transfer it to the blast furnaces. In this paper, we propose the method for trajectory landing position of bucket of reclaimer to fully automate the reclaimer. We use 3-dimensional range finder to detect the shape of a pile. From the image which was detected by 3-dimensional range finder, we extract the outline paths which has same height, and then determine digging height. Finally, we compute the landing point from the outline path. We can prevent overload which can occur on the bucket wheel and guarantee maximum production rate by using the algorithm for determining the landing position on the piles.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1928-1933
• /
• 2005

This Paper is about landing control of legged robot. Body stiffness and damping is used as landing strategy of a legged robot. First, we only used stiffness control method to control legged robot landing. Second control method,sliding mode controller and feedback linearization controller is applied to enhance position control performance. Through these control algorithm, body center of gravity behaves like mass with spring & damping in vertical direction on contact regime.

• Journal of International Academy of Physical Therapy Research
• /
• v.2 no.1
• /
• pp.222-228
• /
• 2011

With comparison of maximum vertical reaction force and lower limb on drop landing between normal and flat foot group, this study is to provide fundamental data of the prevention of injury and the treatment of exercise which are frequently occurred on flat foot group's drop landing. The surface electrodes were sticked on lateral gastrocnemius muscle, medial gastrocnemius muscle, tibialis anterior and the drop landing on a force plate of 40cm was performed with a normal group who had no musculoskeletal disease and a flat foot group of 9 people who had feet examinations. Vertical reaction force were significantly statistically different between two groups(p<.001). Muscle activity of lower limbs in all three parts were not statistically different but showed high tendency on average in the flat foot group. The flat foot group had difficulties in diversification of impact burden and high muscle activity. Therefore, it was suggested that muscular strengthening of knee joints and plantar flexions of foot joints which were highly affected in impact absorption will be required.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.508-511
• /
• 2008

The most landing gear use oleo-pneumatic shock strut to absorb the impact energy during touchdown. The shock strut is composed of the oil damper and the gas spring, especially the oil damper provides resistance force which is proportional to the square of landing speed. In case of high landing speed, the abnormal peak load can be occurred and transferred to the airframe structure. To prevent this, the pressure-relief valve is used to limit the damping force under the specific level. In this paper, it is presented the design process to find optimal damping and analysis results using pressure-relief valve.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.60-68
• /
• 1997

The motion of an aircraft landing gear over rough runway at variable speed is nonstationary. In this paper a method for the computation of nonstationary response variance is presented which uses a state space form for the combination of landing gear and runway excitation. The dynamic characteristics of the landing gear under nonstationary random excitations has also been analyzed using the proposed method. The formulation is for linear systems of arbitrary order and allows any deterministic velocity history. It has been found by a series of simulation that correlation parameter, damping coefficients of landing gear and tire, and velocity profiles plays a prominent role on the dynamic characteristics.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.23 no.1
• /
• pp.56-61
• /
• 2015

Because of kinematic complexities, nonlinear behavior, etc, the performance of oleo-pneumatic landing gear is predicted by qualified commercial softwares. While commercial softwares predict more exactly, it takes a long time to construct or modify a model. At initial design stage, design parameters can be determined quickly and exactly enough with simple 2 degree of freedom model of mass, spring and damping. 2 degree of freedom model can be easily applied to optimization and reliability analysis which takes repetitive computation. In this paper, oleo-pneumatic landing gear is modeled as a nonlinear 2 degree of freedom model. The analysis are compared with landing gear drop test. To determine design parameter, optimization problem is solved with genetic algorithm and 2 degree of freedom model.