• 한국기계가공학회지
• /
• 제19권5호
• /
• pp.91-97
• /
• 2020

A split-die design for the cold forging of symmetric parts such as those having a hexagonal cross-section is presented in this paper. Parts with a hexagonal cross-section, such as bolt heads and nuts, should be forged with a die that has a hexagonal-shaped hole. A split type die is required to mitigate the buildup of stress concentrations located at the corners of the hexagonal hole. Generally, the insert of a hexagonal die is made by cutting each corner of a cylinder using a hexagonal hole and then combined with the die and shrink-fitted. However, split dies face problems when extruding material at the corners of the hexagonal split die. To address this problem, two types of split dies were evaluated: rounded hexagonal dies and angular hexagonal dies. The effects of the pre-stress ring on the dies were compared and analyzed and results show that using the angular split hexagonal die can extend the lifetime of forging dies.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제1권3호
• /
• pp.158-166
• /
• 2001

Based on uniform hot carrier injection (optically assisted electron injection) across the $Si-SiO_2$ interface into the gate insulator of n-channel IGFETs, the threshold voltage shifts associated with electron injection of $1.25{\times}l0^{16}{\;}e/\textrm{cm}^2 between 0.5 and 7 MV/cm were found to decrease from positive to negative values, indicating both a decrease in trap cross section ($E_{ox}{\geq}1.5 MV/cm$) and the generation of FPC $E_{ox}{\geq}5{\;}MV/cm$). It was also found that FNC and large cross section NETs were generated for $E_{ox}{\geq}5{\;}MV/cm$. Continuous, uniform low-field (1MV/cm) electron injection up to $l0^{19}{\;}e/\textrm{cm}^2 is accompanied by a monatomic increase in threshold voltage. It was found that the data could be modeled more effectively by assuming that most of the threshold voltage shift could be ascribed to generated bulk defects which are generated and filled, or more likely, generated in a charged state. The injection method and conditions used in terms of injection fluence, injection density, and temperature, can have a dramatic impact on what is measured, and may have important implications on accelerated lifetime measurements.

• 대한수학회보
• /
• 제24권1호
• /
• pp.23-26
• /
• 1987

The aim of this note is to study some properties of Schrodinger operators, the magnetic case, $H_{0}$ (a)=1/2(-i.del.-a)$^{2}$; H(a)= $H_{0}$ (a)+V, where a=( $a_{1}$,.., $a_{n}$ ).mem. $L^{2}$$_{loc}$ and V is a potential energy. Also, we are interested in solutions, .psi., of H(a).psi.=E.psi. in the sense that (.psi., $e^{-tH}$(a).PSI.)= $e^{-tE}$(.psi.,.PSI.) for all .PSI..mem. $C_{0}$ $^{\infty}$( $R^{n}$ ) (see B. Simon [1]). In section 2, under some conditions, we find that a semibounded quadratic form of H9a) exists and that the Schrodinger operator H(a) with Re V.geq.0 is accretive on a form domain Q( $H_{0}$ (a)). But, it is well-known that the Schrodinger operator H=1/2.DELTA.+V with Re V.geq.0 is accretive on $C_{0}$ $^{\infty}$( $R^{n}$ ) in N Okazawa [4]. In section 3, we want to discuss $L^{p}$ estimates of Schrodinger semigroups.ups.

• 대한기계학회논문집A
• /
• 제38권5호
• /
• pp.527-534
• /
• 2014

본 논문에서는 이미지 기반 전산 모형을 이용하여 섬유강화 복합재료의 기공 탄성 해석을 수행하였다. 먼저 다공성 기지에 대한 단면 이미지를 분석하여 기공도, 기공 개수, 기공 분포 등을 확인하였다. 이미지의 해상도, 위치, 크기에 따른 전산 모형화 및 유한요소 해석을 수행하였으며, 주요 결과로써 유효 탄성 계수, 기공 탄성 인자, 변형 에너지 밀도를 정량적으로 산출하였다. 기공 탄성 인자는 유효 탄성 계수와 기공 압력에 의한 팽창 변형도를 기준으로 계산하였다. 또한 이미지 기반 전산 모형을 이용한 기공 탄성 해석 결과의 신뢰성 확인을 위해, 기공의 형상 및 배열을 단순화시킨 대표 체적 요소 모형의 해석 결과와 비교하였다.

• 한국강구조학회 논문집
• /
• 제11권2호통권39호
• /
• pp.131-142
• /
• 1999

뒤틀림 효과를 고려한 곡선보의 일반적 거동은 Vlasov에 의해 제시된 미분 방정식으로 표시된다. 일반적으로 거더의 단면을 결정하는데 가장 큰 영향을 미치는 요인은 휨모멘트이다. 곡선 교량 계획시 곡선격자형교의 단면을 쉽게 가정하기 위해서 본 논문에서는 직선거더와 곡선거더의 휨모멘트비를 제시하였다. 이 비는 중심각 ${\theta}(L/R)$를 변수로 하여 근사식으로 나타내었다. 이 휨모멘트 근사식과 제시된 영향선은 3경간 곡선격자형교를 보다 쉽게 설계하는데 이용될 수 있다.

• 한국환경생태학회지
• /
• 제16권4호
• /
• pp.433-440
• /
• 2003

백두대간 정령치~고기리 구간에 대해 해발고별 식생변화를 살펴보기 위하여 해발고 l00m마다 10m X 10m(l00$m^2$)의 조사구 5개씩 총 45개 조사구를 9개 지점에 설치하여 조사하였다. 군락의 분리를 위해 TWINSPAN과 DCA기법을 이용하였으며, 그 결과 정령치-고기리 구간은 교목층에서 신갈나무가 우점종인것.으로 밝혀졌으나 해발 900m를 기점으로 아교목층 및 관목층의 부수종을 중심으로 식생구조에 차이가 있는 것으로 밝혀졌다. 유사도지수에서도 유사한 결과를 나타내었으나 종다양도 분석에서는 해발고간 차이가 없었다.

• 대한조선학회지
• /
• 제16권2호
• /
• pp.9-14
• /
• 1979

Havelock was considered the wave resistance of a post extending vertically downwards through the water from the surface, its section by a horizontal plane being the same at all depths and having its breath small compared with its length. This enables us to elucidate certain points of interest in ship resistance. However, the ship has not infinte draft. So, the problem which is investigated in detail in this paper is the wave resistance of a mathematical quadratic model in a uniform stream. The author wishes to study the effect of viriation of draft. The form of the water-plane is varied while keeping in length and the cross sectional area constant. As a numerical example, we calculated the wave resistance for mathematical quadratic ship models. The results are compared with a post having infinite depth. The results are as follows; The models with finer ends have smaller wave resistance up to $V/\sqrt{L}=1.1{\sim}1.2$ than its mate with blunter ends, but above this speed the models with blunter ends have less wave resistance. According to the decrease of draft, the wave resistance gap between the models with blunter ends the models with finer ends decrease at high speed. In this case of T/L=0.025, the models with finer ends have less wave resistance than the models with blunter ends at high speed.

• The Korean Journal of Physiology and Pharmacology
• /
• 제16권3호
• /
• pp.219-224
• /
• 2012

Understanding how the b-wave of the electroretinogram (ERG) is generated by full-field light stimulation is still a challenge in visual neuroscience. To understand more about the origin of the b-wave, we studied the contributions of gap junctions to the ERG b-wave. Many types of retinal neurons are connected to similar and different neighboring neurons through gap junctions. The photopic (cone-dominated) ERG, stimulated by a small light beam, was recorded from goldfish (Carassius auratus) using a corneal electrode. Data were obtained before and after intravitreal injection of agents into the eye under a photopic illumination level. Several agents were used to affect gap junctions, such as dopamine D1 and D2 receptor agonists and antagonists, a nitric oxide (NO) donor, a nitric oxide synthase (NOS) inhibitor, the gap junction blocker meclofenamic acid (MFA), and mixtures of these agents. The ERG b-waves, which were enhanced by MFA, sodium nitroprusside (SNP), SKF 38393, and sulpiride, remained following application of a further injection of a mixture with MFA. The ERG b-waves decreased following $N^G$-nitro-L-arginine methyl ester (L-NAME), SCH 23390, and quinpirole administration but were enhanced by further injection of a mixture with MFA. These results indicate that gap junction activity influences b-waves of the ERG related to NO and dopamine actions.

• 소성∙가공
• /
• 제24권3호
• /
• pp.187-193
• /
• 2015

The objective of the current study is to determine cross-sectional profile of intermediate dies in order to improve the plastic strain homogeneity which directly affects not only the dimensional accuracy but also the mechanical properties of final product by redesigning the intermediate dies using the conventional electric field analysis (EFA) method. Initially, the multi-pass shape wire drawing was designed by using the equivalent potential lines from EFA. The area reduction ratio was calculated from the number of passes in multi-pass shape wire drawing but constrained by the capacity of the drawing machine and the drawing force. In order to compensate for a concentration of strain in a region of the cross section of the wire, the process for multi pass wire drawing from initial round material to an intermediate die was redesigned again using the electric field analysis. Both drawing process designs were simulated by the finite element method in which the strain distribution and standard deviation plastic strain of the cross section of drawn wires were examined.

• 식물분류학회지
• /
• 제48권3호
• /
• pp.153-162
• /
• 2018

Lespedeza maximowiczii C. K. Schneid. (Fabaceae) is a deciduous shrub which is known to be distributed in the temperate forests of China, Korea and on Tsushima Island of Japan. Due to severe morphological variations within species, numerous examinations have been conducted for Korean L. maximowiczii. However, the morphology of Chinese plants has not been studied as thoroughly, despite doubts about their taxonomy. To clarify this taxonomic issue, we investigated morphological characters and undertook a Bayesian clustering analysis with microsatellite markers. The morphological and genetic traits of Chinese individuals varied considerably from those of typical L. maximowiczii growing in Korea. For example, petals of the former had a different shape and bore long claws, while the calyx lobes were diverged above the middle and the upper surface of the leaflet was pubescent. Their terete buds and spirally arranged bud scales were distinct from those within the series/section Heterolespedeza, which includes L. maximowiczii. Our Bayesian clustering analysis additionally included L. buergeri as an outgroup. Those results indicated that the Chinese samples clustered into a lineage separated from L. maximowiczii (optimum cluster, K = 2), despite the fact that the latter is grouped into the same lineage with L. buergeri. Therefore, we treat those Chinese plants as a new species with the name L. pseudomaximowiczii.