• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.310-310
• /
• 2012

확률강우량 산정은 수공구조물의 설계에 있어서 중요한 과정이다. 확률강우량을 산정함에 있어 지난 수십년간 모멘트법, 최우도법, 확률가중모멘트법, 그리고 L-모멘트법 등의 매개변수적 방법이 발달되어 적용되어 왔다. 매개변수적 빈도해석 방법은 그 적용성이 여러 연구를 통해 검정되었지만 가정한 확률분포와 매개변수 추정방법에 따라 확률강우량이 달라지며 강우지속시간과 기후변화 등에 따른 분포의 변동성을 고려해야 하는 단점이 있다. 매개변수적 빈도해석 방법의 단점을 극복하기 위하여 최근에 핵밀도함수 등을 포함한 다양한 비매개변수적 빈도해석 방법이 제안되고 있다. 본 연구에서는 서울기상관측소의 지난 50년간 지속시간 24시간 강우량을 바탕으로 수자원 분야에서 다양하게 적용된 바가 있는 인공신경망 기법과 대표적인 매개변수적 빈도해석 방법인 L-모멘트법을 이용하여 확률강우량을 산정하고 비교하였다. 그 결과 인공신경망 기법은 전통적인 매개변수방법의 하나인 L-모멘트법 보다 확률강우량 산정에 있어서 높은 정확도를 가지는 것으로 나타났다.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.42 no.3
• /
• pp.45-55
• /
• 2000

This study was carried out to derive optimal design low flows bythe Weibull-3 and Wakeby distributions for the partial consecutive duration series at seven watersheds along Han. nagdong, Geum Yeongsan and Seomjin river systems. L-coefficient of variation L-skewness and L-kurtosis were calculated by the L-moment ratio respectively. Parameters were estimated by the method of L-Moments with consecutive duration. Design low flows obtained by method of L-Moments using with consecutive duration, Design low flows obtained by method of L-Moments using different methods for plotting positions formulas in the Weibull-3 and Wakeby distributions were compared by the Root Mean Square Errors(RMSE). It has shown that design low flows derived by the method of L-moments using Weivull plotting position formula in Wakeby distribution were much closer to those of the observed data in comparison with those obtained by the methods of L-moments with the different formulas for plotting positions in Weibull-3 distribution from the viewpoint of Root Mean Square Errors.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.7 no.4
• /
• pp.91-97
• /
• 2003

The maximum moment may occur at interior supports of continuous bridges. If the bigger moment is applied on them, a local yielding at interior supports may occur. They may show plastic behaviors, and the moment will be redistributed. The strength design, L.F.D., redistributes 10% of the negative moment which is obtained from the elastic analysis. However, A.L.F.D method computes the moment which is redistributed. This moment is called automoment. The moment-rotation curve is needed to find automoment. In this paper moment-rotation curve for compact sections suggested from AASHTO Guide Specifications is used to find automoment. Based on A.L.F.D. limit states specification method, a three-span continuous bridge is designed.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.40 no.4
• /
• pp.45-57
• /
• 1998

This study was conducted to derive optimal design floods by Generalized Extreme Value (GEV) distribution for the annual maximum series at ten watersheds along Han, Nagdong, Geum, Yeongsan and Seomjin river systems. Adequacy for the analysis of flood data used in this study was established by the tests of Independence, Homogeneity, detection of Outliers. L-coefficient of variation, L-skewness and L-kurtosis were calculated by L-moment ratio respectively. Parameters were estimated by the Methods of Moments and L-Moments. Design floods obtained by Methods of Moments and L-Moments using different methods for plotting positions in GEV distribution were compared by the Relative Mean Errors(RME) and Relative Absolute Errors(RAE). The results were analyzed and summarized as follows. 1. Adequacy for the analysis of flood data was acknowledged by the tests of Independence, Homogeneity and detection of Outliers. 2. GEV distribution used in this study was found to be more suitable one than Pearson type 3 distribution by the goodness of fit test using Kolmogorov-Smirnov test and L-Moment ratios diagram in the applied watersheds. 3. Parameters for GEV distribution were estimated using Methods of Moments and L-Moments. 4. Design floods were calculated by Methods of Moments and L-Moments in GEV distribution. 5. It was found that design floods derived by the method of L-Moments using Weibull plotting position formula in GEV distribution are much closer to those of the observed data in comparison with those obtained by method of moments using different formulas for plotting positions from the viewpoint of Relative Mean Errors and Relative Absolute Errors.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.42 no.6
• /
• pp.63-71
• /
• 2000

The purpose of this study is to derive optimal design floods by the Wakeby distribution model using the probability weighted moments. Parameters for the Wakeby distribution were estimated by the probability weighted moments for the annual flood flows of the applied watersheds. Design floods obtained by the Wakeby and GEV distributions were compared by the relative mean errors, relative absolute errors and root mean square errors. In general, it has shown that the design floods by the Wakeby distribution using the methods of the probability weighted moments are closer to those of the observed data in comparison with those obtained by the GEV distribution.

• The korean journal of orthodontics
• /
• v.30 no.4 s.81
• /
• pp.467-473
• /
• 2000

As a rectangular wire Is inserted into edgewise brackets the wire exerts a force system three-dimensionally. The force system may include bending force in first and second orders and a torsional force in third order Analytical and experimental studies on bending force have been Introduced, but information about torsion is still lack. The purpose of this study was to estimate the torsional moment in the force system of rectangular arch wires through theoretical and experimental studies. Wires most frequently used for third order control were selected as study materials. Cross sections of 0.016x0.022, 0.017x0.025, 0.019x0.025 inch rectangular wires in foot different materials such as stainless steel(Ormco), TMA(Ormco), NiTi(Ormco), and braided stainless steel (DentaFlex, Dentaurum) were used. The torque/twist rate of each test material was calculated using the torsion formula. Torque/twist rate, yield torsional moment, and ultimate torsional moment were measured with a torque gauge. The torsion formula assesses that the torque/twist rate (T/$\theta$) is proportional to the characteristics of material (G) and cross section (J), and is inversely proportional to the length of wire (L). Most experimental results corresponded with the formula. The relative stiffness was calculated for reference to a logical sequence of wire changes.

• Journal of Korean Society of Steel Construction
• /
• v.11 no.2 s.39
• /
• pp.131-142
• /
• 1999

The general behavior of the curved girder including the warping effects can be presented as the series of differential equations developed by Vlasov. Generally, bending moment is the most important factor for engineer to decide the section of the girder. In order to accommodate easiness of the structural analysis for the curved girder bridge, this paper suggest the ratios of bending moment of curved gilder to that of straight girder. These ratios are presented by an approximate formula setting central angle ${\theta}(L/R)$ as a variable. The approximate formula of the maximum bending moment ratios and influence lines of all stress resultants can be used to design the three-span curved girder bridges.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2004.05b
• /
• pp.1132-1136
• /
• 2004

본 논문은 지금까지의 지점빈도해석의 약점을 보완하기 위하여 지역화의 개념을 사용한 지역빈도해석의 방법에 관한 연구이다. 지점빈도해석은 수문자료의 관측기간이 짧은 경우 정확도에 문제를 발생시킬 수 있으므로, 지점 내 충분한 수의 자료 확보가 선행되어야 한다. 반면 지역빈도해석의 경우 우리나라와 같이 자료의 수가 부족한 경우에도 효율적이고 안정적인 확률수문량을 산정할 수 있다. 본 연구에서는 한강유역의 강우자료 선별을 통해 신뢰성 있는 자료를 구축한 훈, L-모멘트기법과 Netmax법을 사용한 지역빈도해석을 각각 실시하여 기존의 방법으로 산정한 수문량과 비교${\cdot}$분석하였다. 지역빈도해석의 결과 남한강 유역은 이질성 척도가 큰 것으로 판명되어 남한강 유역의 경우 지역적인 세분화가 필요한 것으로 나타났다. Netmax를 이용하여 산정된 수문량은 L-모멘트법과 지점빈도해석 그리고 확률강우량도에 의해 산정된 값에 비하여 과소추정 되었다 지역적 특수성을 고려하지 않고 형성된 네트워크는 지역적으로 세분화가 필요한 지역에 대하여서 좋지 않은 결과를 보여주는 것으로 나타났다.

• The Journal of the Korea Contents Association
• /
• v.8 no.3
• /
• pp.252-263
• /
• 2008

This study was conducted to derive the optimal regionalization of the precipitation data which can be classified on the basis of climatologically and geographically homogeneous regions all over the regions except Cheju and Ulreung islands in Korea. A total of 65 rain gauges were used to regional analysis of precipitation. Annual maximum series for the consecutive durations of 1, 3, 6, 12, 24, 36, 48 and 72hr were used for various statistical analyses. K-means clustering mettled is used to identify homogeneous regions all over the regions. Five homogeneous regions for the precipitation were classified by the K-means clustering. Using the L-moment ratios and Kolmogorov-Smirnov test, the underlying regional probability distribution was identified to be the generalized extreme value (GEV) distribution among applied distributions. The regional and at-site parameters of the generalized extreme value distribution were estimated by the linear combination of the probability weighted moments, L-moment. The regional and at-site analysis for the design rainfall were tested by Monte Carlo simulation. Relative root-mean-square error (RRMSE), relative bias (RBIAS) and relative reduction (RR) in RRMSE were computed and compared with those resulting from at-site Monte Carlo simulation. All show that the regional analysis procedure can substantially reduce the RRMSE, RBIAS and RR in RRMSE in the prediction of design rainfall. Consequently, optimal design rainfalls following the regions and consecutive durations were derived by the regional frequency analysis.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.3C
• /
• pp.105-111
• /
• 2012

Bucket foundations, which are used in the foundations of offshore wind turbines, should be able to withstand large amounts of horizontal and moment loads. Tripod bucket foundation, which combines three single buckets, has been used to increase horizontal and moment capacities. This study performed numerical analysis using ABAQUS (2010), to analyze the group effect and the bearing capacity of a tripod bucket in clay. Parametric studies were performed varying the bucket spacing ratio S/D (S=spacing between the centers of the bucket and the tower; D=diameter of the bucket) and depth ratio L/D (L=embedded length of skirt). The applied constitutive models were a linear elastic perfectly plastic model with Tresca yield criteria for normally consolidated clay and an elastic model for buckets. Loading in the vertical, horizontal, and moment directions was simulated with an increase in each movement at a reference point. The bearing behavior and the capacities of a single and a tripod bucket were compared. Capacity evaluation method of the tripod bucket was suggested using the capacity of a single bucket.