• The Journal of the Korea institute of electronic communication sciences
• /
• v.5 no.3
• /
• pp.327-331
• /
• 2010

The 21.4-22.0GHz frequency band is used to broadcast satellite services in Region 1 and Region 3 in frequency distribution area. The use of this frequency band is according to the provision of the resolution 525 of WRC-03, this frequency band broadcasting service system transmits broadband radio-frequency signals. The trend of the Satellite launching plans for an using this frequency band is growing in worldwide. This frequency band requires fairly more transmit power than the Ku-band because of the rain attenuation of this frequency band is very extreme. An appropriable sharing criteria is required for this broadcast service to be operational.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.5
• /
• pp.971-978
• /
• 2018

This paper deals with the design and implementation of a limiter, which is a key component of the Ku-band radar system. The limiter design with the multi-pin diode switch was complemented by wideband signal attenuation, and realized the physical implementation. In the test result of implemented limiter, when the pin diode switch is all off, it is possible to transmit the incoming signal without distortion. Also when the pin diode switch is turned on sequentially, the input signal is attenuated about 20dB or more step by step. Finally when all of them were turned on, attenuation about 50dB or more were measured for a wide bandwidth(1000MHz) in Ku-band.

• Korean Journal of Remote Sensing
• /
• v.29 no.6
• /
• pp.631-644
• /
• 2013

Significant Wave Height (SWH) data measured by satellite altimeters (Topex/Poseidon, Jason-1, Envisat, and Jason-2) were validated in the seas around Korea by comparison with wave height measurements from marine meteorological buoy stations of Korea Meteorological Administration (KMA). A total of 1,070 collocation matchups between Ku-band satellite altimeter data and buoy data were obtained for the periods of the four satellites from 1992 to the present. In the case of C-band and S-band observations, 1,086 matchups were obtained and used to assess the accuracy of satellite SWH. Root-Mean-Square (RMS) errors of satellite SWH measured with Ku-band were evaluated to roughly 0.2_2.1 m. Comparisons of the RMS errors and bias errors between different frequency bands revealed that SWH observed with Ku-band was much more accurate than other frequencies, such as C-band or S-band. The differences between satellite SWH and buoy wave height, satellite minus buoy, revealed some dependence on the magnitude of the wave height. Satellite SWH tended to be overestimated at a range of low wave height of less than 1 m, and underestimated for high wave height of greater than 2 m. Such regional characteristics imply that satellite SWH should be carefully used when employed for diverse purposes such as validating wave model results or data assimilation procedures. Thus, this study confirmed that satellite SWH products should be continuously validated for regional applications.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.853-861
• /
• 2009

In this paper, we propose the architecture of a multi-band receiver which can receive X-band, Ku-band, K-band and Ka-band signals. For implementing this architecture, we designed a wideband and high power VCO with a buffer stage. In order that a buffer does not affect the characteristic of a oscillation in steady state condition, output impedance of a oscillation part and input impedance of a buffer are orthogonally crossed. The fabricated VCO meets the performance parameter of the multi-band receiver which has a $14.00{\sim}15.20\;GHz$ bandwidth with respect to the tuning voltage, $0.0{\sim}8.0\;V$, and output power of $12{\sim}13\;dBm$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.3
• /
• pp.318-325
• /
• 2019

As satellite communication technology with high efficiency and spatiality evolves, demands of customer for efficient and effective satellite broadcasting services are increasing due to interval reduction of the between satellites, and the limited radio-frequency spectrum resources. Recently, research on antenna that it possible to simultaneously receive multiple signal from various satellites while holding maintain the same number of previous reception channels by using the single reflector has been ongoing. It is necessary to be able to simultaneously receive signals from various satellites in order to maintain the same number of previous reception channels. We suggest a multiband antenna which can be simultaneously and independently receiving Ku band and Ka band satellite broadcasting signals transmitted by three adjacent satellites. We have designed and simulated using commercial design tools TICRA CHAMP and CST MWS to meet the target specifications. It appears that the antenna has -10 dB return loss, and more than 40 dBi directivity gain in Ku band and Ka band respectively.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.3
• /
• pp.33-40
• /
• 1992

In this paper, We designed a 2-stage amplifier for transponder of satellite with dual GaAs FETs NE13783, and performed the worst-case analysis for circuit qualification in the space environment. The bandwidth of amplifier was chosen 11.7-12.2 GHz which is the down link frequency band for domestic Ku-band satellite communication, and the alumina substrate with 25 mil of thickness. The design and optimization of amplifier was achieved by the commercial CAD program TOUCHSTONE and the measurement was performed through the automatic network analyzer.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.2
• /
• pp.33-39
• /
• 2013

In this paper, X/Ku band waveguide diplexers with H-plane T-junction for satellite communication systems is proposed and its characteristics is cinfirmed. Two frequency bands such as X(7.25 ~ 8.4 GHz) and Ku(12.25 ~ 14.5 GHz) can be separated by the proposed waveguide diplexers. A diplexers is normally including low pass filter, high pass filter and junction waveguide. To simplify the structure of the proposed diplexers, the proposed waveguide diplexers is using impedance matching technique on H-plane of the high pass filter without low pass filter. To use vertical and horizontal polarization, the proposed diplexers with orthomode transducer(OMT) characteristics is also designed. Therefore, it is confirmed that the proposed waveguide diplexers can be used as dual-band and dual-polarization diplexers for satellite communication feed systems.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.6
• /
• pp.646-652
• /
• 2014

This paper presents a design and fabrication of Ku-band power amplifier using Gallium Nitride High Electron Mobility Transistor (GaN HEMT) die. In order to fabricate the low-cost Ku-band power amplifier, a Printed Circuit Board(PCB) was used for input/output matching circuits instead of manufacturing process to use an expensive substrate. The measured output power is 42.6 dBm, the drain efficiency is 37.7 % and the linear gain is 7.9 dB under pulse operation at the frequency of 14.8 GHz. Under the continuous wave(CW) test, the output power is 39.8 dBm, the drain efficiency is 24.1 % and the linear gain is 7.2 dB.

• 한국ITS학회:학술대회논문집
• /
• v.2007 no.10
• /
• pp.131-135
• /
• 2007

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.162-166
• /
• 2000

본 논문에서는 Ku-band용 전압제어 유전체 공진 발진기를 위상잡음 특성을 고려하여 설계하였다. 유전체의 높은 Q값은 좋은 위상잡음특성에 영향을 주나 전압제어를 위해 바렉터 다이오드의 연결된 튜닝 마이크로스트립라인의 길이에 따라 Q값의 변화하고 이로 인해 위상잡음 특성이 변화하am로 이를 고려하여 최적의 튜닝 마이크로스트립라인 길이를 시뮬레이션 견과를 통해 얻은 후 전압제어 유진체 발진기를 설계 하였다.