• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.823-828
• /
• 2006

In this paper, we addressed the computer interfacing method using the physical component in our living environment especially, a structure that has plane shape. A beamforming is the one of method for spatial location estimate, when appling it to the structure that has plane shapes, it estimates the event of impings location. and this impings event of specific location can be used for input unit of computing system. we expected, this result will contribute to human-computer interfacing research in home network environment.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.6
• /
• pp.89-95
• /
• 2000

The engine idle speed mode becomes worse as one drives a vehicle for several years. This is due to ageing of engine and power-train parts. In this case, unstable idle conditions such as engine stall and droop are frequently experienced when the engine gets heavy torque loads due to power steering pump and air conditioning compressor. The objective of this paper is to study on the idle speed control using PID controller under load disturbances. The input of the PID controller is an error of rpm. The output of the PID controller is an ISCV duty cycle. The dSPACE Controller Boards are used to interface with engine. The on-vehicle test is realized using by SIMULINK and BLOCKSETS tools. The real time interface control panel supplied by Control Desk S/W is designed to have good results in engine idle speed control.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.05a
• /
• pp.319-324
• /
• 2005

The interface between host processor and the ShortStack Micro Server may be a Serial Communication Interface(SCI). The LonWorks control module with a high performance is developed, which is composed of the 8 bit PIC Microprocessor for host processor and the smart neuron chip for the ShoretStack Micro Server. This intelligent control board is verified as proceeding the various function tests from experimental system with an boost pump and inverter driving systems. It is also confirmed that the developed control module provides stably 0-10VDC linear signal to the input signal of inverter driving system for varying the induction motor speed. Thus, the experimental results show that the fabricating intelligent board carried out very well the various functions in the wide operating ranges of boost pump system. This developed control module expect to apply to industrial fields to require the comparatively exact control and monitoring such as multi-motor driving system with inverter, variable air volume system and the boost pump water supply systems.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2000.11a
• /
• pp.136-139
• /
• 2000

본 연구는 디지털 TV의 다채널화와 관련하여 최근 사용편의성 문제가 중요하게 대두되고 있는 EPG(Electronc Program Guide)와 조작장치를 대상으로 사용자의 요구사항을 분석하고 그에 대한 해결 방안을 제시하고자 하였다. 디지털 방송이 국내에서는 아직 보편화되어 있지 않아 일본 동경 지역 SkyPerfecTV 가입자를 대상으로 다채널 TV 환경에서 디지털 STB(Set Top Box)의 사용실태를 조사하고 분석하였다. 그 결과 간편한 채널 이동 과 EPG 네비게이션 방식, 일대일 TV 환경도래와 개인별 선호 패턴의 극화 현상에 대응한 개인화된 시청환경, 광범위한 정보공간에 대해 제압감을 증강시킬 수 있는 정보표시 방법, 조작수를 줄이며 직접 조작감을 향상시킬 수 있는 입력장치 등에 대한 사용자 요구를 파악할 수 있었다. 이러한 조사결과를 바탕으로 본 연구에서는 “퍼스널 TV”라는 근미래형 인터랙션 스타일을 상정하고 가상 디지털 방송국(D/TV 시뮬레이터)을 기반으로 “퍼스널 컨트롤”과 “스마트 EPG”의 사용자 인터페이스를 개발하였다.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.5 no.10
• /
• pp.1770-1782
• /
• 2011

A brain-computer interface (BCI) is a communication system that translates brain activity into commands for computers or other devices. In other words, BCIs create a new communication channel between the brain and an output device by bypassing conventional motor output pathways consisting of nerves and muscles. This is particularly useful for facilitating communication for people suffering from paralysis. Due to the low bit rate, it takes much more time to translate brain activity into commands. Especially it takes much time to input characters by using BCI-based typewriters. In this paper, we propose a brain-operated typewriter which is accelerated by a language prediction model. The proposed system uses three kinds of strategies to improve the entry speed: word completion, next-syllable prediction, and next word prediction. We found that the entry speed of BCI-based typewriter improved about twice as much through our demonstration which utilized the language prediction model.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.30 no.3
• /
• pp.135-141
• /
• 1994

In order to investigate remotely the behavior and distribution of fishes, the telesounder system which was composed of two parts with a buoy station at sea and a base station on land was manufactured trial. The buoy station at sea consists of fishfinder, transmission interface and transceiver. On the other hand, the base station on land consist of transceiver, receiving interface, trigger/signal separator and color display monitor. The system simulation for the performance of telesounder was carried out by use of echo simulator which could input echo signal into fishfinder. The received power (dBm) of transceiver at 29.4MHz decreased almost in proportion to distance between transmitter and receiver, and the electric field intensity was 12.12mV/m at 100 meters distance from transmitter. The image of color display monitor at the base station on land was very well coincident with the records of fishfinder from the buoy station located at sea. Therefore, it is concluded that the telesounder system is very useful in the analysis of the information on the behavior and the distribution of fishes detected from sea.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.7 s.184
• /
• pp.76-83
• /
• 2006

In this paper, an analysis on a new robot manipulator developed for the side buffing of the shoes is presented. The robot manipulator is composed of five degrees of freedom. An analysis on the forward and inverse kinematics was performed. Through the analysis, an analytic solution was derived for the joint angles corresponding to the position and orientation of the tool in the Cartesian coordinates. The hardware system of the robot composed of the control system, input/output interface system, and related electronic system was developed. The communication system was also developed to interact the robot with the related surrounding systems. A graphic user interface(GUI) program including the forward/inverse kinematics, control algorithm, and communication program was developed using visual C++ language.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.3
• /
• pp.190-197
• /
• 2000

A graphic vehicle modeling pre-processing program and a visualization post-processing program have been developed for AutoDyn7, which is a special program for vehicle dynamics. The Rapid-App for GUI(Graphic User Interface) builder and the Open Inventor for 3D graphic library have been employed to develop these programs in Silicon Graphics workstation. A Graphic User Interface program integrates vehicle modeling pre-processor, AutoDyn7 analysis processor, and visualization post-processor. In vehicle modeling pre-processor, vehicle hard point data for a suspension model are automatically converted into multibody vehicle system data. An interactive graphics capabilities provides suspension modeling aides to verify user input data interactively. In visualization post-processor, vehicle virtual test simulation results are animated with virtual testing environments.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.11A
• /
• pp.1803-1811
• /
• 2001

In this paper, Forward Error Correction(FEC) that is satisfied with ITU-T Recommendation J.83, Annex B(North American Data Over Cable Service Interface Specifications(DOCSIS) for Multimedia Cable Network System(MCNS)) is analyzed. The FEC consist of Reed-Solomon(RS) layer, interleaving layer, randomization layer, and trellis coded modulation(TCM) layer. The effects of quantization of input symbol and of trace-back depth in the Viterbi decoder are simulated over AWGN channels.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.639-643
• /
• 2002

The main purpose of this study was to investigate the formation mechanisms of imperfections such as irregular humps, outer cavity and inner cavity in the laser fusion zone of diamond saw blade. Laser beam welding was conducted to join two parts of blade; mild steel shank and Fe-Co-Ni sintered tip. The variables were beam power and travel speed. The microstructure and elements distributions of specimens were analyzed with SEM, AES, EPMA and so on. It was found that these imperfections were responded to heat input. Irregular humps were reduced in 10.4∼17.6kJ/m heat input range. However there were no clear evidences, which could explain the relations between humps formation and heat input. The number of outer cavity and inner cavity decreased as heat input was increased. Considering both possible defects formations mechanisms, it could be thought that outer cavity was caused by insufficient refill of keyhole, which was from rapid solidification of molten metal and fast molten metal flow to the rear keyhole wall at low heat input. More inner cavities were found near the interface of the fusion zone and sintered segment and in the bottom of the fusion zone. Inner cavity was mainly formed in the upper fusion zone at high heat input whereas was in the bottom at low heat input. Inner cavity was from trapping of coarsened preexist pores in the sintered tip and metal vapor due to rapid solidification of molten metal before the bubbles escaped.