• Journal of Bio-Environment Control
• /
• v.19 no.4
• /
• pp.360-365
• /
• 2010

The effects of precooling treatments on the storability of chicon were investigated during modified atmosphere (MA) storage. The forced air cooling showed faster precooling rate that reduced the internal temperature of chicon to $2{\pm}1^{\circ}C$, and the precooling time of forced air cooling was 1/6 of room cooling. The half cooling time was 3 hr 21 min in room cooling and 1 hr 17 min in forced air cooling. Weight loss was less than 0.5% in all treatments both $5^{\circ}C$ and $10^{\circ}C$ MA storage and maintained higher in forced air cooling treatment. The concentration of carbon dioxide, oxygen, and ethylene of $50{\mu}m$ ceramic film packages were observed higher at $10^{\circ}C$ than $5^{\circ}C$. The precooling effect on respiration reduction was not shown at $5^{\circ}C$, but appeared that the gas concentration of precooling treatments showed less carbon dioxide and higher oxygen than non precooling treatment by 9 days after $10^{\circ}C$ storage. Ethylene concentration of precooling treatments showed lower than non precooling treatment until 3 days both $5^{\circ}C$ and $10^{\circ}C$ MA storage. Precooling showed the effect on maintaining visual quality of chicon both $5^{\circ}C$ and $10^{\circ}C$ MA storage. However, the forced air cooling that showed faster precooling rate did not appeared more precooling effect on the visual quality than room cooling because the fast air flow (6.0 m/sec) of forced air cooling hit directly on chicon outer leaves and might cause physical damage to chicon. Although the forced air cooling showed the effect on maintaining quality of chicon, but additional studies should be needed that investigated proper air flow rate and cooling box structure can prevent physical damage by air flow.

• Journal of Bio-Environment Control
• /
• v.18 no.3
• /
• pp.291-296
• /
• 2009

This study was conducted to compare the storability of 6 chicory cultivars for producing chicon; 'Vintor', 'Focus', 'Metafora', 'Kibora', 'Nobus', and 'Redoria Red' grown in 2 regions: Chuncheon (plain region) and Pyeongchang (high land region). Chicons were produced from chicory roots that grown for 120days and then stored for over 120days at $2^{\circ}C$ and 90% of RH conditions. To produce chicon, chicory root was forced at $18^{\circ}C$ for 22days with suppling the nutrient solution ($KNO_30.54g{\cdot}L^{-1}$, $Ca(NO_3)_2\;1.02g{\cdot}L^{-1}$, $MgSO_4\;0.36g{\cdot}L^{-1}$, $KH_2PO_4\;0.21g{\cdot}L^{-1}$, $K_2SO_4\;0.10g{\cdot}L^{-1}$, pH 7.0). Chicons produced from 6 different chicory cultivars packed with $25{\mu}m$ ceramic film and stored for 25days at $8^{\circ}C$. The fresh weight of chicon in MAP was maintained to 99.5% of pre-storage weight. The fresh weight of 'Redoria Red' was lowest in all cultivars, and that of Chuncheon region cultivated treatment was lower than Pyeongchang treatment. The $CO_2$ and $O_2$ concentration in chicon MAP were 2% and $10{\sim}17%$. There were not significantly different among cultivars and between regions, although 'Redoria Red' cultivar showed highest $CO_2$ and lowest $O_2$ concentrations. The ethylene concentration in chicon MAP was $1.0{\mu}{\iota}{\cdot}{\iota}^{-1}$ and also didn't show any significant difference among all treatments. Chicon detoriorated visual quality with appearing russet spotting that result from ethylene gas. The visual quality of 'Redoria Red' cultivar decreased faster than the other cultivars. 'Metafora', 'Focus', and 'Kibora' maintained higher firmness of their leaf than the others, and the firmness was higher grown in Pyeongchang region cultivated treatments than in Chuncheon region.

• Journal of Bio-Environment Control
• /
• v.23 no.2
• /
• pp.109-115
• /
• 2014

This study examined the uplift bearing capacity of spiral steel pegs according to the degree of soil compaction and embedded depth in a small-scaled lab test. As a result, their uplift bearing capacity increased according to the degree of soil compaction and embedded depth. The uplift bearing capacity under the ground condition of 85% compaction rate especially recorded 48.9 kgf, 57.9 kgf, 86.2 kgf and 116.6 kgf at embedded depth of 25 cm, 30 cm, 35 cm and 40 cm, respectively, being considerably higher than under other ground conditions. There were huge differences in the uplift bearing capacity of spiral steel pegs according to the compaction conditions of ground. Their maximum uplift bearing capacity was 116.6 kgf under the ground condition of 85% compaction rate and at embedded depth of 40 cm, and it is very high considering the data of spiral steel pegs. It is thus estimated that wind damage can be effectively reduced by careful maintenance of ground condition surrounding spiral steel pegs. In addition, spiral steel pegs will be able to make a contribution to greenhouse structural stability if proper installation methods are provided including the number and interval according to the types of greenhouse as well as fixation of plastic film. The findings of the study indicate that the optimal effects of spiral steel pegs for greenhouse can be achieved at embedded depth of more than 35cm and compaction degree of more than 85%. The relative density of the model ground in the test was 67% at compaction rate of 85%.

• Research in Plant Disease
• /
• v.22 no.1
• /
• pp.18-24
• /
• 2016

This study was conducted to elucidate the cultural and pathogenic characteristics of Cladosporium cucumerinum PT1 and resistance of 81 commercial cucumbers (Cucumis sativus). Cucumber leaves and fruits appeared as scab were collected from a plastic film house located in Pyeongtaek, Gyeonggi-province, Korea in late March, 2015. A casual fungus was isolated from the diseased fruits on potato dextrose agar and it was identified as C. cucumerinum PT1 based on the morphological characteristics. To find out the effect of wounding and fruit size on the development of cucumber scab, small (<10 cm long), medium (10 to 20 cm long), and large (>20 cm long, commercially mature fruit) size cucumber fruits were harvested, C. cucumerinum PT1 pathogens were inoculated with a single droplet of suspension ($1{\times}10^5$ spores/ml) on wounded or unwounded cucumber fruits. Small fruits were completely damaged with showing severe water-soaking symptoms and fast pathogen growth regardless of wounded or unwounded. Meanwhile slight water-soaking symptoms on medium and large size fruits occurred and disease development into plant tissues was observed only on wounded fruits. Disease resistance of 81 commercial cucumber cultivars was evaluated on third-stage seedlings and small fruits by inoculating suspension ($1{\times}10^5$ spores/ml) of C. cucumerinum PT1. As a result, mini and pickling cultivar groups were resistant, 'Cheoeumcheoreom' cultivar was symptomless and the other cultivars were resistant to medium resistant. On the other hand, most of cucumber cultivars belonging to the other groups were susceptible. Disease resistance of cucumber against cucumber scab was significantly different among cultivars and a few cucumber cultivars showed different disease resistant responses to two bioassay methods using seedlings and small fruits. Therefore, to screen scab resistance in cucumber, a test using both fruits and seedlings is advisable. We think that the selected resistant cultivars can be used to control cucumber scab effectively under the farmhouse condition.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.1379-1385
• /
• 2007

In domestic transitional zone design, there is regulation to prevent generation of irregular substructure behaviors that negatively influence in prevention of plasticity settlement on approach section and contact section as well as relieve overall track rigidity by reducing sectional foundation and track stiffness difference, but design guideline that considers dynamic behavior of transitional track in actual service line is very insignificant. Therefore in this study, characteristics of transitional track dynamic behaviors by substructure stiffness are researched and measured dynamic response of transitional track by substructure stiffness in order to prove correlation between substructure and track and calculate elasticity(stiffness) and track load of transitional track by using measurement and formula to provide basic information for developing design guideline considering dynamic behavior of service line transitional track.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.517-528
• /
• 2007

Domestic or international existing researches regarding rail damage factors are focused on laying, vehicle conditions, driving speed and driving habits and overlook characteristics of track structure (elasticity, maintenance etc). Also in ballast track, as there is no special lateral spring stiffness of track also called as ballast lateral resistance in concrete track, generally, existing study shows concrete track has 2 time shorter life cycle for rail replacement than ballast track due to abrasion. As a result of domestic concrete track design and operation performance review, concrete track elasticity is lower than track elasticity of ballast track resulting higher damage on rail and tracks. Generally, concrete track has advantage in track elasticity adjustment than ballast track and in case of Europe, in concrete track design, it is recommended to have same or higher performance range of vertical elastic stiffness of ballast track but domestically or internationally review on lateral spring stiffness of track is very minimal. Therefore, through analysis of service line track on site measurement and analysis on performance of maintenance, in this research, dynamic characteristic behaviors of commonly used ballast and concrete track are studied to infer elasticity of service line track and experimentally prove effects of track lateral spring stiffness that influence curved rail damage as well as correlation between track elasticity by track system and rail damage to propose importance of appropriate elastic stiffness level for concrete and ballast track.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.551-557
• /
• 2007

This paper describes a study on the permeability reduction of the riverbed ground during urban railway tunnel construction. The research is mainly concentrated on the study of the grouting or injection methods among permeability reduction methods which can be adapted in the riverbed ground. Firstly, the various grouting methods are theoretically reviewed and compared based on the previous research papers and case study results. It is also evaluated the grouting methods in view of a safe construction of the river crossing railway tunnel. Baced on the literature review and previous construction data, the design technology of grouting methods considering the long term hydro-geological behaviour in the riverbed, is suggested. Two injection methods namely, Natural Durable Stabilizer(N.D.S) and Space-Multi Injaction Grouting(S.M.I) methods, are introduced as new approach methods which can be adopted to modify the riverbed ground. In order to evaluate the ground that grouted and modified by the N.D.S and S.M.I method, the pilot test programmes including the field and laboratory permeability tests, are carried out in the river crossing tunnel construction sites. The results obtained from pilot test programme, are also reviewed. In conclusion, the grouting efficiency of the S.M.I method using the non-alcalimeter silica sol is better than that of NDS method using cement. In addition, it hopes that the research results are contributed to develop the grouting design technology.

• Radiation Oncology Journal
• /
• v.20 no.2
• /
• pp.165-171
• /
• 2002

Purpose : In order to perform craniospinal irradiation (CSI) in the supine position on patients who are unable to lie in the prone position, a new simulation technique using a CT simulator was developed and its availability was evaluated. Materials and Method : A CT simulator and a 3-D conformal treatment planning system were used to develop CSI in the supine position. The head and neck were immobilized with a thermoplastic mask in the supine position and the entire body was immobilized with a Vac-Loc. A volumetrie image was then obtained using the CT simulator. In order to improve the reproducibility of the patients' setup, datum lines and points were marked on the head and the body. Virtual fluoroscopy was peformed with the removal of visual obstacles such as the treatment table or the immobilization devices. After the virtual simulation, the treatment isocenters of each field were marked on the body and the immobilization devices at the conventional simulation room. Each treatment field was confirmed by comparing the fluoroscopy images with the digitally reconstructed radiography (DRR)/digitally composite radiography (DCR) images from the virtual simulation. The port verification films from the first treatment were also compared with the DRR/DCR images for a geometrical verification. Results : CSI in the supine position was successfully peformed in 9 patients. It required less than 20 minutes to construct the immobilization device and to obtain the whole body volumetric images. This made it possible to not only reduce the patients' inconvenience, but also to eliminate the position change variables during the long conventional simulation process. In addition, by obtaining the CT volumetric image, critical organs, such as the eyeballs and spinal cord, were better defined, and the accuracy of the port designs and shielding was improved. The differences between the DRRs and the portal films were less than 3 mm in the vertebral contour. Conclusion : CSI in the supine position is feasible in patients who cannot lie on prone position, such as pediatric patienta under the age of 4 years, patients with a poor general condition, or patients with a tracheostomy.

• Journal of Bio-Environment Control
• /
• v.19 no.3
• /
• pp.159-164
• /
• 2010

This study was carried out to compare the storability of Salsola komarovi Iljin and Suaeda maritima L. Dum which stored at different storage temperatures in MA storage. These plants that had grown in greenhouse packed with $50\;{\mu}m$ ceramic film and then stored in $2^{\circ}C$, $10^{\circ}C$, and $25^{\circ}C$ temperature. The fresh weight loss both plants was less than 1% in all temperature treatments. The highest fresh weight loss showed at $25^{\circ}C$ among storage temperature treatments in Salsola komarovi Iljin between plants. The highest carbon dioxide contents in package showed at $25^{\circ}C$ among storage temperature treatments in Salsola komarovi Iljin between plants, and at $2^{\circ}C$ and $10^{\circ}C$ temperature treatments remained less than 1%. Oxygen contents in package both plants showed the highest level at $2^{\circ}C$ temperature treatment, but Salsola komarovi Iljin showed less oxygen contents than Suaeda maritima L. Dum. Although there was no significant difference ethylene contents in package between $2^{\circ}C$ and $10^{\circ}C$ temperature treatments, the higher showed in $10^{\circ}C$ than $2^{\circ}C$ temperature treatments. The ethylene contents in package both plants were roughly $20\;{\mu}L{\cdot}L^{-1}$ and the higher was in Suaeda maritima L. Dum than Salsola komarovi Iljin at $2^{\circ}C$. As increasing the storage temperature, the contents of carbon dioxide and ethylene in package also increased in both plants. The carbon dioxide and ethylene contents of Salsola komarovi Iljin showed a significant difference between $2^{\circ}C$ and $10^{\circ}C$ temperature treatments, but Suaeda maritima L. Dum did not show. The shelf life of Salsola komarovi Iljin based on visual quality was 14 days at $2^{\circ}C$ temperature treatment and 7.5 days at $10^{\circ}C$ temperature treatment. However, the shelf life of Suaeda maritima L. Dum did not show a significant difference between $2^{\circ}C$ temperature treatment that was 11 days, and $10^{\circ}C$ temperature treatment that was 9.5 days. Considering visual quality and gas contents in package, Suaeda maritima L. Dum might appear chilling injury at $2^{\circ}C$ temperature treatment.

• Journal of Nutrition and Health
• /
• v.3 no.3
• /
• pp.129-135
• /
• 1970

From the previous studies, F-P-4 formula was found to be comparable to full fat dry milk in its nutritive value and feeding performance. However, an attempt was made in order to make sure whether or not any possibility might exist, by which further improvement of nutritive quality and simultaneous reduction of product costs may be achieved. Using F-P-4 as a control, modifications were made in new formulas, F-P-5, F-P-6 and F-P-7 by reducing FPC, eliminating yeast from the mixture, and by enriching with methionine as needed. In particular, F-P-7 is completely free of FPC, hydrogenated oil and yeast. Yet, levels of total protein and fat were kept equal to those of F-P-4 in all formulas. An animal feeding test for all formulas using 10 female rats per group for 8 weeks and an infant feeding trial for F-P-5 and F-P-6 with 5 of each female infants under age of one for one month were conducted along with F-P-4 as a control. Almost the same results were obtained with F-P-4, 5 and 6, but F-P-7 showed the lowest body weight gain. FER of F-P-5 and 6 was 0.20 as was with F-P-4, while that of F-P-7 was 0.16. Acceptability to infants was excellent; growth, appearance and biochemical data were normal. As an example F-P-4 packed in 0.04mm polyethylene bags was used for storage study at $25^{\circ}C$ and relative humidity of $65{\sim}85%$ for 8 months. Although viable bacterial counts and vitamin C contents were reduced, peroxide and TBA values were increased gradually during such storage. Since there are also significant changes in color and organoleptic quality, the expected shelf life under the given conditions is considered to be about 2 months and thus further works are needed both on the product and packaging in order to improve the storage stability. Either elimination of yeast form F-P-4, that is F-P-5, or partial replacement of FPC with methionine, that is F-P-6 may well reduce material costs about 10%. Considering blending process of ingredients, F-P-5 is thus found to be the best formula developed. While F-P-7 free of FPC is inferior in its nutritive quality than that of others, but significantly superior than of rice. Furthermore, the material cost of the product can be reduced about 20% from that of F-P-4. And thus this vegetable blend is considered to be useful as a low cost supplementary food mixture for growing children.