• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.1
• /
• pp.20-27
• /
• 2010

This paper describes a design of 5-stage pipelined de-blocking filter with power reduction scheme and proposes a efficient memory architecture and filter order for high performance H.264/AVC Decoder. Generally the de-blocking filter removes block boundary artifacts and enhances image quality. Nevertheless filter has a few disadvantage that it requires a number of memory access and iterated operations because of filter operation for 4 time to one edge. So this paper proposes a optimized filter ordering and efficient hardware architecture for the reduction of memory access and total filter cycles. In proposed filter parallel processing is available because of structured 5-stage pipeline consisted of memory read, threshold decider, pre-calculation, filter operation and write back. Also it can reduce power consumption because it uses a clock gating scheme which disable unnecessary clock switching. Besides total number of filtering cycle is decreased by new filter order. The proposed filter is designed with Verilog-HDL and functionally verified with the whole H.264/AVC decoder using the Modelsim 6.2g simulator. Input vectors are QCIF images generated by JM9.4 standard encoder software. As a result of experiment, it shows that the filter can make about 20% total filter cycles reduction and it requires small transposition buffer size.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.7
• /
• pp.68-73
• /
• 2009

This paper describes design and implementation of a spread spectrum clock generator (SSCG) for the DisplayPort. The proposed architecture generates the spread spectrum clock using a sigma-delta fractional-N PLL. The SSCG uses a digital End order MASH 1-1 sigma-delta modulator and a 9bit Up/Dn counter. By using MASH 1-1 sigma-delta modulator, complexity of circuit and chip area can be reduced. The advantage of sigma-delta modulator is the better control over modulation frequency and spread ratio. The SSCG generates dual clock rates which are 270MHz and 162MHz with 0.25% down-spreading and triangular waveform frequency modulation of 33kHz. The peak power reduction is 11.1dBm at 270MHz. The circuit has been designed and fabricated using in 0.18$\mu$m CMOS technology. The chip occupies 0.620mm$\times$0.780mm. The measurement results show that the fabricated chip satisfies the DispalyPort standard.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.10
• /
• pp.82-90
• /
• 2011

Because of the development of Smart phone devices, the demands of high performance FPU(Floating-point Unit) becomes increasing. Therefore, we propose the high-speed single-/double-precision FPU design that includes an elementary add/sub unit and improved multiplier and compare and convert units. The most commonly used add/sub unit is optimized by the parallel rounding unit. The matrix operation is used in complex calculation something like a graphic calculation. We designed the Multiply-Add Fused(MAF) instead of multiplier to calculate the matrix more quickly. The branch instruction that is decided by the compare operation is very frequently used in various programs. We bypassed the result of the compare operation before all the pipeline processes ended to decrease the total execution time. And we included additional convert operations that are added in IEEE754-2008 standard. To verify our RTL designs, we chose four hundred thousand test vectors by weighted random method and simulated each unit. The FPU that was synthesized by Samsung's 45-nm low-power process satisfied the 600-MHz operation frequency. And we confirm a reduction in area by comparing the improved FPU with the existing FPU.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.05a
• /
• pp.667-671
• /
• 2001

The Instant Messenger(IM) is the most popular personal communication tool today. IM is a tool that can substitute E-mail for a person, and can secure the user for a company. Further, it is claimed as it has a limitless potential. However, there has been several reports on security issues. It has known that the transmitting message is not secured for the attacks, and hacking tools has been developed. In addition, several reports has been made regards to the vulnerability. In other words, anyone can been through and manipulate the messages that are sent or received via IM. This is a barrier for the IM to be developed as a corporate's strategic tool, and furthermore, it will create serious personal privacy issue. IETF IMPP Working Group is preparing a standard mutual relationship between IM. However, it is complicated due to the American On-Lines's absence, whom has ensured the most number of IM users. There was a discussion only about the form of the transmitting data, but it is insufficient state to discuss the security service for general. In this paper, I design and implement the Secure Instant Messaging System, to solve the IM's vulnerability and the security issue presented above.

• Journal of Practical Engineering Education
• /
• v.12 no.1
• /
• pp.117-125
• /
• 2020

According to the government's smart factory promotion project for small and medium-sized enterprises, more than 10,000 intelligent factories are scheduled or already built in the country and the government-led goal is to nurture 100,000 skilled workers by 2022. Smart Factory introduces numerous types of education and training courses from the supplier's point of view, such as training institutions belonging to local governments, some universities, and public organizations, in the form of an efficient resource management system and ICT technology convergence in the automated manufacturing equipment. The lack of linkage with the NCS, the standard for training, seems to have room for rethinking and direction. Results of survey is provided for the family companies of K-University in the metropolitan area and Chungnam area, and analyzes job demands by identifying whether or not they want to introduce smart factories. Defining the practitioners who will serve as a window for the introduction of smart factory technology within the company, setting up a training goal in consideration of the career path, and including the level of training required competency units, optional competency units, and training time suitable for introducing and operating smart factories. Author would like to present an NCS-based qualification design plan.

• International Journal of Highway Engineering
• /
• v.20 no.1
• /
• pp.47-58
• /
• 2018

PURPOSES : The purpose of this study is to evaluate the mechanical properties of a cold-recycling asphalt mixture used as a base layer and to determine the optimum emulsified-asphalt content for ensuring the mixture's performance. METHODS : The physical properties (storage stability, mixability, and workability) of three types of asphalt emulsion (CMS-1h, CSS-1h, and CSS-1hp) were evaluated using the rotational viscosity test. Asphalt emulsion residues, prepared according to the ASTM D 7497-09 standard, were evaluated for their rheological properties, including the $G*/sin{\delta}$and the dynamic shear modulus (${\mid}G*{\mid}$). In addition, the Marshall stability, indirect tensile strength, and tensile-strength ratio (TSR) were evaluated for the cold-recycling asphalt mixtures fabricated according to the type and contents of the emulsified asphalt. RESULTS : The CSS-1hp was found to be superior to the other two types in terms of storage stability, mixability, and workability, and its $G*/sin{\delta}$ value at high temperatures was higher than that of the other two types. From the dynamic shear modulus test, the CSS-1hp was also found to be superior to the other two types, with respect to low-temperature cracking and rutting resistance. The mixture test indicated that the indirect tensile strength and TSR increased with the increasing emulsified-asphalt content. However, the mixtures with one-percent emulsified-asphalt content did not meet the national specification in terms of the aggregate coverage (over 50%) and the indirect tensile strength (more than 0.4 MPa). CONCLUSIONS : The emulsified-asphalt performance varied greatly, depending on the type of base material and modifying additives; therefore, it is considered that this will have a great effect on the performance of the cold-recycling asphalt pavement. As the emulsified-asphalt content increased, the strength change was significant. Therefore, it is desirable to apply the strength properties as a factor for determining the optimum emulsified-asphalt content in the mix design. The 1% emulsified-asphalt content did not satisfy the strength and aggregate coverage criteria suggested by national standards. Therefore, the minimum emulsified-asphalt content should be specified to secure the performance.

• International Journal of Highway Engineering
• /
• v.12 no.2
• /
• pp.9-16
• /
• 2010

Roughness is the most important factor to maintain the road performance, and affects greatly on the design life in Jointed Plain Concrete pavements. Also, the factors the evaluate pavement‘s commonality is the three method such as functionality, safety and structural performance. In evaluating function of road, representative factors is the roughness, which has been used to determine maintenance time as key standard. As research for roughness is absence in pavement design. Applied roughness-model had a low-reliability in Korea. Therefore, it is needed to develop reliable model in road roughness. In this research, uniform specific is applied to distribute them after selecting the concrete pavements. Concrete pavement is divided by sections of 238. Total length of this sections has 281km and account for 16% of total road length in korean concrete pavements for selected sections. Considering the korean roughness-model, the evaluation of roughness is performed for the freezing index, average annual rainfall, condition for the base, the amount of traffic as well as spalling(%), cracking(%), age(year) at the selected section at the selected section. Also, additional sections is selected to evaluate various age which affects on the roughness. As a result of the analysis, it showed that spalling(%), cracking(%), age(year), and the condition of the base affected road roughness. When the correlation with the road roughness was analyzed, the reliable model for road roughness was proposed, and the ratio that can explain road roughness was R2-68.8% and P value-0 which is statistically meaningful.

• Journal of the Institute of Convergence Signal Processing
• /
• v.14 no.4
• /
• pp.261-269
• /
• 2013

This paper describes the design and development of VSI (VLBI standard interface) optical adapter for transmitting VLBI(Very long baseline interferometry) observation data with optical signal. VSI cable comprised of 80-line is being used for observed data transmission with maximum length of 5-meter between playbacks (Mark5B, VERA2000) and raw VLBI data buffer (RVDB), RVDB and VLBI correlation subsystem (VCS) in Daejeon correlator. It has a plan to conduct the data processing for 16-stations and introduce the 14 RVDB systems in near future. And data loss frequently occurred because of trouble of VSI cable MDR80 connector. By considering the data loss by connector error of VSI cable, RVDB system extension plan, effective space usage and long distance data transmission(e-VLBI), the VSI optical adapter was proposed and developed for effectively transmitting and receiving VLBI data through optical signal. In order to confirming the performance of developed VSI optical adapter, the experiments for data transmission was conducted between playback and RVDB system, and confirmed that data transmission was clearly done without any data loss.

• KIPS Transactions on Computer and Communication Systems
• /
• v.6 no.3
• /
• pp.105-112
• /
• 2017

PCI Express is a bus technology that connects the processor and the peripheral I/O devices that widely used as an industry standard because it has the characteristics of high-speed, low power. In addition, PCI Express is system interconnect technology such as Ethernet and Infiniband used in high-performance computing and computer cluster. PGAS(partitioned global address space) programming model is often used to implement the one-sided RDMA(remote direct memory access) from multi-host systems, such as computer clusters. In this paper, we design and implement a OpenSHMEM API based on PCI Express maintaining the existing features of OpenSHMEM to implement RDMA based on PCI Express. We perform experiment with implemented OpenSHMEM API through a matrix multiplication example from system which PCs connected with NTB(non-transparent bridge) technology of PCI Express. The PCI Express interconnection network is currently very expensive and is not yet widely available to the general public. Nevertheless, we actually implemented and evaluated a PCI Express based interconnection network on the RDK evaluation board. In addition, we have implemented the OpenSHMEM software stack, which is of great interest recently.

• Fire Science and Engineering
• /
• v.21 no.4
• /
• pp.1-11
• /
• 2007

This study aims to investigate, review, and summarize the definition, development, and applications of "percent agent in pipe", "percent of agent in pipe" which is used as a key factor in testing and evaluating the performance of gaseous fire extinguishing agents, including Halon 1301 and $CO_2$. This study also analyzes and compares the local and international standards on testing and evaluating the performance of gaseous fire extinguishing systems, as well as the results of system performance tests conducted as a part of performance evaluation and approval programs for gaseous fire extinguishing systems, especially, Korean Gaseous Fire Extinguishing System Performance Approval Program called KFI Approval. Percent agent in pipe was defined first in NFPA 12A, Standard on Halon 1301 Fire Extinguishing Systems, dating back to the 1970's. After the phaseout of Halon 1301 systems in 1994 in the developed countries, the percent agent in pipe has been widely used in Halon 1301 alternative clean agent fire extinguishing systems, both halocarbon clean agent systems and inert gas clean agent systems, as an essential criterion to assure the system design accuracy, determine the limitations and performance of a system, and to predict the system performance results accurately, especially, in association with their system flow calculations. Underwriters Laboratories has their own standards such as UL 2127 and 2166 applying percent agent in pipe in testing and evaluating the performance of clean agent fire extinguishing systems. As a part of a system performance test and approval program called KFI Approval System, Korea also has started to apply the percent agent in pipe as a key factor to test, evaluate, and approve the performance of gaseous fire extinguishing systems, including both high and low pressure $CO_2$ systems, from the early 2000's. This study outlines and summarizes the relevant UL and KFI standards and also describes the actual test resultant data, including the maximum percents of agent in pipe for gaseous fire extinguishing systems. As evidenced in lots of tests conducted as a part of the system performance test and approval programs like KFI Approval System, it has been proven that the percent agent in pipe may work as a key factor in testing, evaluating, and determining the limitations and performance of gaseous fire extinguishing systems, especially compared with the hydraulic flow calculations of computer design programs of gaseous fire extinguishing systems, and will remain as such in the future. As one thing to note, however, there are some difficulties in using the unified percent agent in pipe to determine the maximum lengths of pipe networks for gaseous fire extinguishing systems, because the varying definitions used by some of the flow calculations (not in accordance with NFPA 12A definition) make it impossible to do any direct comparison of pipe lengths based on percent agent in pipe.