• Journal of Fisheries and Marine Sciences Education
• /
• v.23 no.2
• /
• pp.210-220
• /
• 2011

The Keyongin Inland waterway will connect with Han-River and the Northen part of the Incheon-seaway and this way will be opened at the early of October this year. In this regard, the Incheon container terminal is under constructing for 1,000 TEU & 550 TEU container vessels at the place of leftside of the Seohae lockgate. However the terminal length is not still fixed due to at a great expenses of construction and dosposal matter of the dredged soil. So this paper will suggest the optimum berth length by using the full mission shiphandling simulator for berthing and unberthing shipmaneuvering. And also evaluates the design standard of harbor construction rules and analysis optimum berth length against ship's length for safe shiphandling at terminals in accordance with the customary practices of the major ports in Korea.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.10 no.3
• /
• pp.62-70
• /
• 2007

Most design temperature of environmental test in korea is based on the standard of Department of Defense. There are few studies to establish temperature standard. Besides the representative environmental test guide 'MIL-STD-810F' encourage to tailor to generate the most relevant test data possible and to test to make a match of test environment with operational environment. Under these circumstances, it is irrational to comply with baseless daily cycle. Thus the study about design method of test temperature is essential. So, the daily cycles to be appropriate to the Korean peninsula was presented in this study. And this research shows how to derive two main element, frequency-of-occurrence and daily maximum (minimum) temperature in daily cycles, in case we can not find the daily cycle.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.5 no.2
• /
• pp.27-33
• /
• 1968

The resistance decreasing effects of a bulbous bow have been investigated with the model test results of the Korean standard type 10,000GT cargo vessel equipped with several different sized bulbous bows. The best bulbous bow for the design is 3.66% bulb which decrease the residual resitance 5%. The new hull combined with a bulbous bow have to be designed in other to get more effects.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2008.04a
• /
• pp.288-293
• /
• 2008

The standard prestressed concrete I-girder bridge (PSC I-girder bridge) is one of the most prevalent types for small and medium bridges in Korea. When determining the member forces in a section to assess the safety of girder in this type of bridge, the general practice is to use the simplified practical equations or the live load distribution factors proposed in design standards rather than the precise analysis through the finite element method or so. Meanwhile, the live load distribution factors currently used in Korean design practice are just a reflection of overseas research results or design standards without alterations. Therefore, it is necessary to develop an equation of the live load distribution factors fit for the design conditions of Korea, considering the standardized section of standard PSC I-girder bridges and the design strength of concrete. In this study, to develop an equation of the live load distribution factors, a parametric analysis and sensitivity analysis were carried out on the parameters such as width of bridge, span length, girder spacing, width of traffic lane, etc. Then, an equation of live load distribution factors was developed through the multiple linear regression analysis on the results of parametric analysis. When the actual practice engineers design a bridge with the equation of live load distribution factors developed here, they will determine the design of member forces ensuring the appropriate safety rate more easily. Moreover, in the preliminary design, this model is expected to save much time for the repetitive design to improve the structural efficiency of PSC I-girder bridges.

• Journal of information and communication convergence engineering
• /
• v.14 no.4
• /
• pp.268-271
• /
• 2016

An efficient inductive switching noise suppression technique for mixed-signal integrated circuits (ICs) using standard CMOS digital technology is proposed. The proposed design technique uses a parallel RC circuit, which provides a damping path for the switching noise. The proposed design technique is used for designing a mixed-signal circuit composed of a ring oscillator, a digital output buffer, and an analog noise sensor node for $0.13-{\mu}m$ CMOS digital IC technology. Simulation results show a 47% reduction in the on-chip inductive switching noise coupling from the noisy digital to the analog blocks in the same substrate without an additional propagation delay. The increased power consumption due to the damping resistor is only 67% of that of the conventional source damping technique. This design can be widely used for any kind of analog and high frequency digital mixed-signal circuits in CMOS technology

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.10a
• /
• pp.262-267
• /
• 2008

The long-term wind data are reconstructed from the short-term meteorological data to design the 4 MW offshore wind park which will be constructed at Woljeong-ri, Jeju island, Korea. Using two MCP (Measure-Correlate-Predict) models, the relative deviation of wind speed and direction from two neighboring reference weather stations can be regressed at each azimuth sector. The validation of the present method is checked about linear and matrix MCP models for the sets of measured data, and the characteristic wind turbulence is estimated from the ninety-percent percentile of standard deviation in the probability distribution. Using the Gumbel's model, the extreme wind speed of fifty-year return period is predicted by the reconstructed long-term data. The predicted results of this analysis concerning turbulence intensity and extreme wind speed are used for the calculation of fatigue life and extreme load in the design procedure of wind turbine structures at offshore wind farms.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.05a
• /
• pp.346-348
• /
• 2005

This paper presented problems occurred in design and construction of LPS(Lightning Protection System) based on the new KS(Korea Standard), and proposed various solution for those. Imperfect KS, poor data on lightning characters in Korea lack of train for engineer, immature SPD engineering and absence of LPS design sample for various buildings are main problems. We suggested that comprehensive measures attending every persons and organizations relevant LPS are needed to solve the problems.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10b
• /
• pp.803-808
• /
• 1998

As carbon fiber is a light-weight materials, high tensile strength and durability compared with rebar, the retrofitting method for RC structures using carbon fiber sheet (CFS) must be use widely. In this paper, the tensile strength test for carbon fiber sheet variable of CF's weight and elastic modulus to evaluate the design tensile strength of carbon fiber sheet which is needed for the strengthening design of CFS and the calculation of strengthening effect. As a result, the design tensile strength of CFS can be calculate using the effect coefficient of strengthening(α) of CFS, the average tensile strength of CFS and the standard deviation of CFS(equation 5)

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.23 no.56
• /
• pp.55-64
• /
• 2000

There is more than a single quality characteristic and they are often of varying or mixed target types. The purpose of this paper is to develop general strategies for solving the multiple response robust design problem. The desirability function provides an important tool to solve problems that have different types of target since the desirability values all the range between zero and one. Several combinations of arithmetic averages, geometric averages, and standard deviations are used in the various strategies to find the best design point.

• Journal of the Korea Safety Management & Science
• /
• v.2 no.2
• /
• pp.139-153
• /
• 2000

To develope a domestic machinery industry, international competition through reducing cost by increasing productivity is as important as evolving technology and increasing quality. In this study, we have studied in application of GT technology. GT is a skill that acquires high productivity using part's resemblance for multi part and small size production like mass production. We have classified group, such as design, layout and the others, to be applied systematically. The design group includes retrieval for drawings and study for GT design. The layout group includes GT layout, analysis of production process and study for composition method. And others include scheduling, standardization and standard process.