• Journal of the Earthquake Engineering Society of Korea
• /
• v.23 no.2
• /
• pp.89-99
• /
• 2019

In order to increase the seismic safety of nuclear power plant (NPP) structures, a technique to reduce the seismic load transmitted to the NPP structure by using a seismic isolation device such as a lead-rubber bearing has recently been actively researched. In seismic design of NPP structures, three directional (two horizontal and one vertical directions) artificial synthetic earthquakes (G0 group) corresponding to the standard design spectrum are generally used. In this study, seismic analysis was performed by using three directional artificial synthetic earthquakes (M0 group) corresponding to the maximum-minimum spectrum reflecting uncertainty of incident direction of earthquake load. The design basis earthquake (DBE) and the beyond design basis earthquakes (BDBEs are equal to 150%, 167%, and 200% DBE) of G0 and M0 earthquake groups were respectively generated for 30 sets and used for the seismic analysis. The purpose of this study is to compare seismic responses and seismic fragility curves of seismically isolated NPP structures subjected to DBE and BDBE. From the seismic fragility curves, the probability of failure of the seismic isolation system when the peak ground acceleration (PGA) is 0.5 g is about 5% for the M0 earthquake group and about 3% for the G0 earthquake group.

• Journal of the Korea Concrete Institute
• /
• v.15 no.5
• /
• pp.689-696
• /
• 2003

Recently, Appendix A of ACI 318∼02 Code introduced the Strut-and-Tie Model(STM) procedure in shear design of deep flexural members. The STM procedure is widely used in the design of concrete regions where the distribution of longitudinal strains is significantly nonlinear, such as deep beams, beams with large openings, corbels, and dapped-end beams. Experimental study included five high-strength reinforced concrete deep beams with different detailing schemes for the horizontal and vertical reinforcement. The specimens were designed as simply supported beams subjected to concentrated loads on the top face and supported on the bottom face. At failure, all specimen exhibited primary diagonal crack running from the support region to the point load. Specimens which had mechanical anchorages(terminators) gives better representation of the load-carrying mechanism than the specimen had standard 90-degree anchorage at failure in deep flexural members. Based on the test results, shear design procedures contained in the ACI 318-99 Code, Appendix A of the ACI 318-02 Code, CSA A23.3-94 Code and CIRIA Guide-2 were evaluated. The Shear design of ACI 318-99 Code, Appendix A of the ACI 318-02 Code and CIRIA Guide-2 shown to be conservative predictions from 10% to 36% in the shear strength of the single-span deep beam which was tested. ACI 318-99 Code was the lowest standard deviation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.12
• /
• pp.7403-7415
• /
• 2014

This study points out a problem that the vehicle rotation area provided in a dead-end parking lot for apartment blocks is misused as unreasonable parking places but accordingly, the edge parking spaces are rarely used for parking. Therefore, this study aims to establish a parking design standard to improve the parking convenience and land-use efficiency by investigating the real parking behaviors and problems identified in the study area, multiple apartment blocks in Haeundae-gu, Busan. This study calculated two simple linear regression models for two mutually exclusive factors, such as the parking convenience and land-use efficiency, respectively, and specified a trade-off point that optimizes both factors. The study results found that parking convenience and land-use efficiency can be improved by not only changing the misused vehicle rotation area to normal parking spaces depending on the usage pattern, but also by increasing the width of the edge parking spaces from 2.3m to 2.6m. Finally, this study suggests two parking design cases for more realistic design applications by considering the parking environment in the dead-end parking lot for apartment blocks.

• Journal of the Korean Society of Safety
• /
• v.22 no.4
• /
• pp.96-101
• /
• 2007

Usually pictograms embedded in safety signs are such final means to transmit hazard information that the importance of them cannot be emphasized too much. Nevertheless, in Korea, few people are interested in safety signs and their functions so that evaluation of safety signs are seldom committed nor safety signs draw workers' attention to fulfill their functions. Therefore this research aimed to standardize the procedure for developing safety signs in order not only to give practical help to industrial workers but to match them international standards, and to develop a few examples through the suggested standard procedure. As results, a procedure for developing industrial safety signs was developed by combining both ANSI Z535.3 and ISO 9186 with a special emphasis on action inducibility as the former emphasized as well as comprehensibility as the latter suggested. According to test results with undergraduate students as well as industrial workers on a few signs developed through the suggested procedure, action inducibility was higher whereas confusion rate was lower than expected on one hand, and it could be concluded that the procedure would supply results that can be satisfied on the other hand.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.168.2-168.2
• /
• 2010

The growing market for geothermal heat pump system requires great consideration of quality control and assurance in design and construction. The borehole heat exchanger of GHP system should be sustainable, economical and ecological. Thermal Response Test (TRT) is a useful method for site investigation to obtain reliable data for a optimal system design from the technical and economical aspect. Intensive researches combined with exchange of experiences on an international level within the IEA ECES Annex 21 improved the technology. Major subjects on the interpretation of TRT are development of improved evaluation models, evaluation of the TRT with respect to geological layers and investigation of the influence of ground water. Current status of TRT in South Korea, as well as a new version of the Korean TRT standard test procedure was presented. TRT is mostly used for governmental supported projects with corresponds to more than 100 GCHP systems per year. More than 200 tests are applied, mostly on single U-tube heat exchangers (about 95%). Bentonite is the most common grouting to be used. KIGAM (Korea Institute of Geoscience & Mineral Resources) is also keeping a GIS geological and geothermal database. In the institute also laboratory measurements of rock properties are carried out. About 90% of the laboratory measurements of the rock heat conductivity shows higher values than the in-situ TRT.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.6
• /
• pp.403-410
• /
• 2006

Eddy current testing (ECT) signals produced by a differential bobbin coil probe vary according to probe design parameters such as the number of turns, geometry and coil gap size. In the present study, the characteristics of a differential bobbin coil probe signals are investigated by numerical simulation in order to determine the optimum coil gap. For verification of numerical simulation accuracy, a specially designed bobbin probe of which the coil gap can be adjusted is fabricated and a series of experiments to acquire signals from two kinds of standard tubes with the variation in coil gap is performed. Then, the experimental signals are compared to the simulation results. Based on this investigation, a decision on the optimum range of coil gap is made. The theoretically predicted signals agree very well to the experimental signals. In fact, this excellent agreement demonstrates a high potential of the simulation as a design optimization tool for ECT bobbin probes.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.26 no.2
• /
• pp.39-47
• /
• 2020

Purpose: Clinical laboratory of hospital has been demanded to extension or relocation regarding with the test number increase and analyzer development. Space area criteria per test numbers, lab functions, hospital bed and lab staffs are needed for draft space programing. So, the purpose of this study is to provide the space area guideline of clinical laboratory for space calculation in planning and design the spatial environment. Methods: Literature review has been used in checking the standards and guidelines. And questionnaire surveys to laboratory supervisors in hospitals have been conducted for the data collection. 60 answers have been analysed statistically by MS Excel program. Results: The result of this study can be summarized into three way calculations. The first one shows that the basic standard workspace and distance is applied in lab design. The second one shows that average space area criteria resulted from case studies is applied by 19㎡ per one staff, 0.9~1.0㎡ per one bed, and lastly linear length calculation of workbenches and analyzers on the bench top and floor mount, is multiplying it by the sum of the counter depth plus aisle width. Implications: In updating the space area calculation guidelines, it is necessary to cooperate with medical staffs and designers.

• The Journal of Korea Robotics Society
• /
• v.10 no.3
• /
• pp.171-177
• /
• 2015

A telerobot offers a more engaging and enjoyable interaction with people at a distance by communicating via audio, video, expressive gestures, body pose and proxemics. To provide its potential benefits at a reasonable cost, this paper presents a telepresence robot system for video communication which can deliver speaker's head motion through its display stanchion. Head gestures such as nodding and head-shaking can give crucial information during conversation. We also can assume a speaker's eye-gaze, which is known as one of the key non-verbal signals for interaction, from his/her head pose. In order to develop an efficient head tracking method, a 3D cylinder-like head model is employed and the Harris corner detector is combined with the Lucas-Kanade optical flow that is known to be suitable for extracting 3D motion information of the model. Especially, a skin color-based face detection algorithm is proposed to achieve robust performance upon variant directions while maintaining reasonable computational cost. The performance of the proposed head tracking algorithm is verified through the experiments using BU's standard data sets. A design of robot platform is also described as well as the design of supporting systems such as video transmission and robot control interfaces.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.5 no.3
• /
• pp.37-48
• /
• 2003

'Pattern' is of very unique nature in each and every country around the world, and its aesthetic feeling of 'pattern' has been handed down according to its nationality and cultural development process. That is, 'pattern' is ornament to symbolize each country's aesthetic standard or choice through some shape, reflecting social consciousness or religion philosophy. Mostly based upon literature survey and case study, this survey paper analytically compares oriental botanical pattern with occidental botanical figure, which has been influenced by Buddhism-Confucianism and Christian religion respectively. The results show that some patterns are commonly used in both area, while meaning differently in some cases: lotus (life), pomegranate (wealth and prosperity in orient, resurrection in occident), grape (fecundity in orient, wealth in occident), dangcho (fecundity in orient, victory in occident). And the other patterns look uniquely used either just in orient or only in occident. For instance, oriental area had its own patterns such as peony (meaning wealth and honour), peach (longevity), ume flower (happiness), orchid (fecundity); while occidental area used lily (purity), olive (peace), palm (victory), and so on. Interestingly, the botanical patterns were used as main patterns in orient whereas as minor in occident.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.26 no.3
• /
• pp.328-336
• /
• 2017

The exit surface of a lens is designed using a three-dimensional free-form expression in order to easily modify a curved surface. This enables the design of numerical values and mathematical things using three-dimensional free-form expression, and enhances precision because it can be fine-tuned via numerical control. The standard of "Classification of Luminaire Light Distribution" for outdoor lighting fixtures by IESNA is adopted in order to examine the correlation between three-dimensional free-form surface expression and lighting performance. The variation of light distribution type and range is analyzed using the values of maximum light intensity and 50% light intensity. The actual tolerance occurs owing to parameters such as the thickness of the lens, the distance between LEDs, and the movement of the center of the incident surface; the effects of changes in these parameters on the performance are compared and analyzed.