• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.12
• /
• pp.1185-1191
• /
• 2011

The kinematic characteristics of cutting device significantly affects cutting performance in 2-dimensional elliptical vibration cutting(EVC) where the cutting tool cuts workpiece, traversing a micro-scale elliptical trajectory in a trochoidal motion. In this study, kinematical characteristics of EVC device constructed with two parallel stacked piezoelectric actuators were analytically modeled and compared with the experimental results. The EVC device was subjected to step and low-frequency(0.1 Hz) sinusoidal inputs to reveal only its kinematical displacement characteristics. Hysteresis in the motion of the device was observed in the thrust direction and distinctive skew of the major axis of the elliptical trajectory of the cutting tool was also noticed. Discrepancy in the voltage-to-displacement characteristics of the piezoelectric actuators was found to largely contribute to the skew of the major axis of the elliptical trajectory of the cutting tool. Analytical kinematical model predicted the cutting direction displacement within 10 % error in magnitude with no phase error, but in estimating the thrust direction displacement, it showed a $27^{\circ}$ of phase-lag compared with the measured displacement with no magnitude error.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.9
• /
• pp.896-902
• /
• 2007

This paper proposes a vision-based kinematic control method for mobile robots with camera-on-board. In the previous literature on the control of mobile robots using camera vision information, the forward velocity is set to be a constant, and only the rotational velocity of the robot is controlled. More efficient motion, however, is needed by controlling the forward velocity, depending on the position in the corridor. Thus, both forward and rotational velocities are controlled in the proposed method such that the mobile robots can move faster when the comer of the corridor is far away, and it slows down as it approaches the dead end of the corridor. In this way, the smooth turning motion along the corridor is possible. To this end, visual information using the camera is used to obtain the perspective lines and the distance from the current robot position to the dead end. Then, the vanishing point and the pseudo desired position are obtained, and the forward and rotational velocities are controlled by the LOS(Line Of Sight) guidance law. Both numerical and experimental results are included to demonstrate the validity of the proposed method.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.288-297
• /
• 1994

The sewing machine is one of the oldest machine that has ever used, which is related with clothes' life. Modern sewing machines are divided into three groups by the sititch character, which are the lock stitch sewing machine group, the over lock sewing machine group and the specical sewing machine group. The lock stitch sewing machine have being used more than any others, which is also good model to study. This work is part of the improvement of an industrial lock stitch(ILS) sewing machine's design. The research objectives are the kinematic analysis and evaluations of stitch performance. The feed dog and the needle extreme's motion, which are important two part's motion in the sewing machine, are characterized by the stitch process and the needle trace. The needle trace is formulated as the stitch spacing, the stitch spacing's ratio(the static characteristic), and the stitch's phase difference(the dynamic characteristic). The tested ILS sewing machine is evaluated as a good static characteristic and a bad dynamic characteristic. Namely, a stitch spacing's ratio is 0.01~0.063(mm/mm) and a stitch's phase difference ratio is 0.06~0.13(mm/mm).

• Journal of Korean Physical Therapy Science
• /
• v.15 no.3
• /
• pp.55-63
• /
• 2008

Background : The Purposes of this study were to understand difference between free walking and obstacle over walking through the naked eye and motion analysis device, and to review merits of obstacle walking training as item of functional assessment in clinical situations. Methods : All participants were male and performed 3 types of walking methods: free walking, obstacle over walking with low block(height=10cm, width=8cm), and obstacle over walking with high block(height=20cm, width=8cm). All walking were performed 3 trials respectively. Results : In the naked eye, initial contact with toes occurred more than heel strike in obstacle over walking, and the flexion angle of hip and knee were increased in obstacle over walking. On interpretations though motion analysis device, cadence, gait speed and weight accept were significant statistically(p<.05). Cadence and gait speed were decreased, and weight accept duration was increased in obstacle over walking. Rotation among three pelvic motions was significant statistically(p<.05), flexion among three hip motions was significant statistically(p<.05) and flexion among three ankle motions was significant statistically(p<.05). Rotation and flexion among three ankle motions was significant statistically(p<.05). Conclusion : Both the naked eye and interpretations of the device presented many difference between free walking and obstacle over walking. In overcrossing obstacles, many participants appeared walking strategy by perform initial contact with toes. Knee flexion was most significant statistically(p<.05) in obstacle over walking with 20cm block.

• The Journal of Korea Robotics Society
• /
• v.15 no.3
• /
• pp.212-220
• /
• 2020

This paper deals with a strategy of gain optimization for the kinematic control algorithm of a wire-driven surgical robot. The proposed controller consists of the closed-loop inverse kinematics with the back-calculation method. The closed-loop inverse kinematics has 18 PID control gains, and the back-calculation method has 6 gains. An efficient strategy is designed to optimize 18 values first and then the remaining 6 values. The optimal gain sets are searched under the step input with performance indices. In this gain optimization, the objective function is defined as the minimum value of signal-to-noise ratio of the performance indices for 6 DoF (Degree-of-Freedom) motion that is based on the Taguchi method, and the constraints are applied to obtain stable responses for each motion evenly. The gain sets obtained are verified by simulations using the test trajectories. In comparative results, the optimal gain value based on the performance index combined with ISE (integral of square error) and settling time showed the best control performance.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.5
• /
• pp.543-547
• /
• 2009

This paper describes the design, simulation, development, and experiment of a six degree-of-freedom micropositioning parallel manipulator. A movable stage was supported with six links, each of which extends with a dc-servo micropositioning actuator. In case of parallel manipulator, while the solution of the inverse kinematics is easily found by the vectors of the links which are composed of the joint coordinates in base and platform, but forward kinematic is not easily solved because of the nonlinearity and complexity of the parallel manipulator's kinematic output equation with the multi-solutions. The movable range of the prototype was ${\pm}25mm$ in the x- and y-directions and ${\pm}12.5mm$ in the z-direction. The minimum incremental motion of the prototype was $1{\mu}m$ in the x- and y-directions and $0.5{\mu}m$ in the z-direction. The repeatability of the prototype was ${\pm}2{\mu}m$ in the x- and y-directions and ${\pm}1{\mu}m$ in the z-direction. The motion performance was also evaluated by not only the computer simulation of CAD model but also the experiment using a capacitive sensor system.

• Korean Journal of Applied Biomechanics
• /
• v.24 no.4
• /
• pp.317-327
• /
• 2014

As a single subject study, it was purposed to investigate kinematic differences between Yang Hak Seon vault (i.e., handspring forward and salto forward straight with triple twist, Yang-1 vault hereafter) and Tsukahara $1260^{\circ}$ twist with salto forward straight (Yang-2 vault hereafter) in gymnastics. Yang Hak-Seon (23 years, 160 cm, and 52 kg) voluntarily participated in this study. Motion capture system, consisting of fourteen cameras, were used to measure Yang-2 vault with the sampling rate of 200 Hz. Twenty six reflective markers were placed on major anatomical points of 15 body segments. Successful two trials of Yang-2 vault were collected and analyzed for the comparison. Compared Yang-1 results were based on the previous study of Park and Song (2012). Results indicated superior linear kinematics of Yang-1 vault to those of Yang-2 vault before the touchdown of vault table. However, Yang-2 vault revealed superior angular kinematics to Yang 1 vault showing more trunk twist angle (a triple and a half twist) and its faster angular velocity during the airborne. The Yang 2 vault could has advantage of increasing angular motion than Yang 1 vault as a result of a half turn off the springboard onto the vault table and a sequential touchdown of the hands.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.3
• /
• pp.51-60
• /
• 2007

The purpose of this study was to kinematically analyze the differences between short(2.17 m) and long(10.94 m) putting stroke motions. Thirteen male professional golfers were participated in this study. Experiment was conducted on the artificial grass mat in the gymnasium. Kinematic data were collected by the 60 Hz Kwon3D motion analysis system. Differences were compared by SPSS paired t-test and one-way ANOVA. Duncan was used for post-hoc test and a=.05. The results were as follows: 1. Ground projected trajectory of the putter head were statistically straight during both short and long putts. 2. There was no consistent alignment tendency among shoulder, hip, and stance alignments. However stance alignment was consistent between short and long putts. Thus it is assumed that professional golfers align their body based on their stance alignment. 3. During putting, shoulder rotated not only up and down but also right and left. 4. Left and right elbow distance was maintained during all phases of the putts for both short and long putts. 5. Inter foot distance of long putting was longer than that of short putting.

• Physical Therapy Rehabilitation Science
• /
• v.10 no.2
• /
• pp.98-105
• /
• 2021

Objective: The purpose of this study was to examined the kinematic relationship and differences through the range of motion (ROM), muscle activity, and vertical ground reaction force (VGRF) during forward and backward lunge movements, which are effective in improving muscle strength and balance ability of the lower extremities, and to provide clinical information on more efficient lunge movements. Design: Cross-sectional study Methods: Fifteen adult males who met the selection criteria were tested for their dominant feet.Forward and backward lunges were then performed, and the ROM, muscle activity, and VGRF were measured for kinematic analysis during the lunge movement.The differences betweenthe forward lunge and backward lunge intervention were examined using a paired t-test. Results: A significant increase in the ROM of the knee and ankle was observed during the forward and backward lunges (p<0.05). In addition, in terms of the muscle activity, the peak values of the vastus medialis oblique (VMO) and VGRF also showed a significant increase in the forward lunge compared to the backward lunge (p<0.05). Conclusions: This study showed an increase in VGRF peak value, knee and ankle ROM, and VMO muscle activity during forward lunge. Based on these results, it is considered necessary to apply differently depending on the direction of progress in consideration of the musculoskeletal situation and physical ability during the lunge movement.

• Korean Journal of Applied Biomechanics
• /
• v.13 no.3
• /
• pp.277-291
• /
• 2003

This study was designed to examine the kinematic factors in the phase during the marche fente motion. For this study, the subjects were 5 elite male fencing players. The direct linear transformation (DLT) method was used in calculating 3-D coordinate of the digitized body parts. The cubic spline function was used for smoothing and the kinematic data for displacement, velocity, angle variables were calculated for Kwon3d ver 2.1. And the following conclusions were drawn; 1. It show that the marche phase appeared to longer time than the pante phase In the performance time. For the fast attack, it showed that the subjects should be moving in a short stride width. 2. For a fast and stable movement posture in the marche phase, the vertical change of COG must be maintain the same position as possible, but all subjects appeared to decrease the COG because of a excessive the knee flection. 3. In the COG velocity change, all the subjects showed to the same change in both the marche and the fente phase. However in the attack extremity velocity, it increased velocity in order of upper arm, fore arm, and hand in the marche phase, but it showed different velocity among each subjects at the moment of stabbing. So that in order to do effective stabbing, they have to extend their upper extremity max and do faster the distal segment than the proximal segment. 4. It showed to take a fast and stable movement, because some subjects showed the big anteroposterior angle of the trunk flexed max shoulder angle and elbow angle of their attack arm and the other upper extremity.