• Journal of the Korean Institute of Educational Facilities
• /
• v.22 no.1
• /
• pp.37-45
• /
• 2015

Over the years, great attention has been shown to the function of the campus facilities that should be well-equipped, operated and maintained to better support university's two main goals: providing education and supporting research. Properly managing campus facilities is the initial step to be prepared to meet the rapidly changing global educational standard. However, so far, no definitive answer has been given to the question of what service level/scope is appropriate for the effective campus facility management (FM) in Korea. Therefore, at the outset, it is imperative to establish the framework for the standardized campus FM services. The main focus of this research is to provide comprehensive understanding on the campus FM by establishing the framework in the form of FM performance indicator (PI). As the first step, FM standards set by Korean Agency for Technology and Standards (KATS) has been thoroughly reviewed and analyzed to establish the framework for FM standards applicable to campus facility management. Secondly, extensive literature review on the development of performance indicator (PI) for the educational facilities has been conducted to classify PI types and complement FM_KS. Finally, specific guideline and PIs developed by APPA which is globally well-known association in the field of FM for higher education facilities has been added to the combined PI which is the mixed form of FM_KS and PIs from the previous literature. This research provides campus facility managers and FM outsourcing service providers with framework in the form of PI to support future directions of effective campus FM services.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.407-408
• /
• 2010

This study investigated fire resistance performance for ultra-high-strength concrete columns reinforced with various fibers such as polypropylene, nylon, and steel fibers. 24 small size column specimens were tested with standard heating curve of KS F 2257-1 for 3 hours. The main parameters were the aggregate types, the length of polypropylene fibers, and the content ratios of each fiber.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.14 no.3
• /
• pp.3-11
• /
• 2008

As the elderly population is growing rapidly, guidelines for planning and designing of the elderly housing are required for improving housing environment of the elderly. The purpose of this study is making the basic dimensional standardization of residential spaces for the elderly. The dimensional standard of spaces suggested in this guideline considers characteristics of both aged and the general users. The spaces studied in this research include bedroom, living room, bathroom, kitchen and other circulation spaces in the elderly housing. The design guidelines of furniture, equipment for the aged with sizing of the areas are provided. Finally, applicability of the output is reexamined by implementing this guidelines to the sample planning and design of the elderly housing.

• Journal of Korean Society for Quality Management
• /
• v.47 no.2
• /
• pp.315-325
• /
• 2019

Purpose: The purpose of this study was to propose useful standards evaluation method using standards networks by analyzing the relationship between normative references citation information list. Methods: The collected data through the survey were analyzed using social network analysis. The measurement tools used for this study were divided into three dimensions such as certificate standard, normative reference and degree centrality. Results: The results of this study are as follows; regarding the influence of standard information, It is meaningful that the research using normative reference item among the bibliography information that the standard itself possesses. The analysis of social network analysis data of population standard, normative reference and the correlation analysis with sales, a variable representing actual utilization performance, suggested the importance of the standard and how to evaluate it. Conclusion: In prioritizing standard maintenance, more efficient management will be possible if centrality figures of standard network information are analyzed and used for standard maintenance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.55-55
• /
• 2009

In this paper, we introduce the status of certificate test on crystalline silicon photovoltaic, module in Korea. Up to 5. 2009, about 200 models have passed certificate test under KS C IEC61215 standard. Most products are from Korea, Japan, China. And some are from USA, German and Taiwan. A few environmental test items' results and standard test methods will be discussed. The detail discussion will be shown in the following paper.

• KIEAE Journal
• /
• v.13 no.2
• /
• pp.107-112
• /
• 2013

The purpose of this study is to analyze an insulation property and to establish a design standard for the underground space in architecture. Insulation materials for this study are 12 kinds of Insulation which qualified KS standards(3 classes of EPS type 1, 3 classes of EPS type 2(Neopor), 3 classes of XPS and 3 classes of PU Boards). For insulation materials of underground space, insulating and water tightening property are desired. So conductivity for insulating and water absorption for water tightening are measured in this study. Temperature, insulation is exposed to in the underground space, is different from temperature above the ground. Conductivity is measured in a temperature of $17^{\circ}C$, $20^{\circ}C$, $23^{\circ}C$ and $26^{\circ}C$. In KS standards, water absorption are measure after 24 hours, but insulation is exposed to water for a long time in the underground. So after 110 days, water absorption are measured. As time goes by, increasing of water absorption means decreasing of water tightening and insulating. So after water absorption had measured for 110 days, conductivity has measured again. As a result, XPS is selected as optimized insulation for underground. And Conductivity of XPS insulation with water should be added by 20%.

• Journal of the Korea Institute of Building Construction
• /
• v.13 no.1
• /
• pp.29-37
• /
• 2013

In this study, a zero-cement brick is manufactured by replacing cement with recycled aggregates and blast furnace slag powder. Experimental tests were conducted with standard sized samples of $190{\times}57{\times}90mm$ (KS F 4004), and this manufacturing technique was simulated in practice. Results showed that the zero-cement brick with 0.35 W/B had the highest compressive strength, but the lowest absorption ratio. This absorption ratio of zero-cement brick with 0.35 W/B was lower than the required level determined by KS F 4004. Hence, to increase the absorption ratio, crushed fine aggregate (CA) and emulsified waste vegetable oil (EWO) were used in combination in the zero-cement brick. It was found that the zero-cement brick with CA of 20% and EWO of 1% had the optimum combination, in terms of having the optimum strength development (12 MPa) and the optimum absorption ratio (8.4%) that satisfies the level required by KS. In addition, it is demonstrated that for the manufacturing of zero-cement brick of 1000, this technique reduces the manufacturing cost by 5% compared with conventional cement brick.

• Journal of the Korean Institute of Gas
• /
• v.12 no.3
• /
• pp.81-84
• /
• 2008

In this paper, the research was applied the mixture gas of Propane-DME (dimethyl ether) for being commercialization to residential gas ranges. In order to examine a correspondence between Korean Standard and thermal efficiency characteristics at each burner, experiments were performed with 100% Propane and the mixture gas of 80% Propane-20% DME. The experimental results were shown that the higher a mixture ratio of DME was used, the lower a thermal efficiency was gained. Those were due to low caloric value of DME. With 80% Propane-20% DME mixture gas, one of residential gas ranges was not satisfied the condition for the thermal efficiency value, 40%, Korean Standard. Consequently, the research needs about the standard for being commercialization to the mixture gas of Propane-DME.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.4
• /
• pp.457-465
• /
• 2021

This study analyzed the reality and problems of the defense standard classification system. This paper proposes a plan to perform standard management tasks efficiently through case analysis of domestic and foreign standard classification systems. To continuously solve the problem of military product quality in defense technical data, it is necessary to promptly reflect the civilian's excellent technology and benchmark the civilian standard system to manage high-quality defense standards. First, to analyze the reality, the NATO classification system was analyzed through the private KS of domestic and ICS codes, the US defense standard system of overseas. In the case of the Korean military, the reality of the defense standard classification system was grasped through the National Defense Standards Comprehensive System operated by the Defense Acquisition Program Administration. The classification of the ministry of defense's weapon system and force support system is the most suitable classification system for the Korean military, which is classified into eight weapon systems and six force support standard systems for all steps. Specifically, it was classified into 12 major categories, 66 categories, and 352 sub-categories. In this study, the establishment of the defense standard management system can improve the classification system of new defense standards by reflecting the superior technology of the private sector.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.4A
• /
• pp.475-485
• /
• 2008

This paper intends to enhance the reliability and performance of domestic elastomeric bearings through the proposal of directions for the improvement of their stiffness regard to the Korean industrial standard KS F 4420 relative to the evaluation of design/fabrication/quality. Therefore, comparative analysis of the compressive elastic modulus, stiffness measurement method and performance evaluation method of KS F 4420 with those of Eurocode, Japanese bearing manual, and ISO code was performed, and measurement tests on the compressive stiffness and shear stiffness of common elastomeric bearings produced in Korea were conducted. The experimental results reveal that differences of about 20% and 13% occurred respectively for the compressive stiffness and shear stiffness according to the definition adopted for the stiffness. The measured values for the stiffness of the domestic elastomeric bearings were also verified to exhibit large deviation from the formula proposed by KS F 4420. Elastomeric bearings that does not have appropriate compressive stiffness required at the design can result in uneven deflection at supports of bridges and excessive stress in girders. Accordingly, the establishment of compressive elastic modulus formula and performance evaluation criteria fitted to the domestic circumstances through the execution of performance evaluation of bearings presenting diversified shapes and shape factors appears to be necessary for the domestic bearings to meet the performance required in design.