• Korean Journal of Poultry Science
• /
• v.45 no.4
• /
• pp.285-290
• /
• 2018

This study was aimed to evaluate the possibility of application to the KS A ISO 2859-1 Easy test, an international standards sampling inspection, to replace a sampling method of the current grading standard of chicken meats for the first time. As a result of screening capability to check for defective products, the current sampling was 0.61 and the KS A ISO 2859-1 Normal test was 0.70, suggesting that the latter inspection method was more accurate. If the KS A ISO 2859-1 conversion principle is applied, 40,530 won per day is saved for a 50-lot inspection. The current sampling and the KS A ISO 2859-1 Easy test did not exceed the reject limit for the number of defective products to satisfy the grade $1^+$ on chicken carcass size numbers 12, 9 and 8. Freshness was not significantly different between the current sampling and the KS A ISO 2859-1 Easy test. It is expected that using the KS A ISO 2859-1 Easy test with a smaller sample volume will have the same level of quality evaluation as the current sampling method while reducing costs.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.7 no.2 s.25
• /
• pp.7-12
• /
• 2007

This study has been conducted to present reform recommendations for Standardization of Construction Materials, based on a study on the Investigation of Demander's Consciousness for Construction Materials Quality and Information Standardization in Korea. Upon investigation, it was found that the quality of Korea Industrial Standards (KS) was given 67 points (out of 100) by respondents. In addition, 38% of the respondents showed that they had problems with a lack of Standardized Information. Good examples were found to be non-standardized materials, e.g. admixtures, waterproof agents, reinforcing fibers, concrete, aggregates, adhesives, wood, temporary materials, thermal-insulating materials, etc. Upon results from the investigation of demander's consciousness for infrastructure of standardization of information, 71.2% of respondents thought that it is necessary to informatize construction materials. They made following demands on the informatization to be, in order: Quality, Standard, Price (Cost), Operation, Drawing, Law, and Information.

• Journal of the Korean Society for Railway
• /
• v.16 no.4
• /
• pp.246-252
• /
• 2013

The vibration characteristics of railway vehicles are very complex because they are not only dependent on vehicle and track conditions but also on operating conditions. Vibration can cause the failure of rolling stock equipment. To verify that the quality of rolling stock equipment is acceptable, it should be able to withstand vibration tests of reasonable magnitude and duration. There are many standards for vibration and shock tests of equipment in Korea. In this paper, we have reviewed and compared the standards (KS R 9144, R 9146 and IEC 61373) for vibration and shock tests.

• Journal of Sericultural and Entomological Science
• /
• v.27 no.2
• /
• pp.54-63
• /
• 1985

This studies has been carried out how to effect on electrostafic propensity of synthetic fabrics by coating with 0.5% acrylic polymer solution which was previously developed by the author to improve anticrease nature of silk. The work conditions are: (A) Applied synthetic polymer was acrylic polymer 525, developed by the author. (B) Electrostatic voltage for various fabrics were carried out by Korea standard abrasion partner with Korea standard (KS K 0905) cotton, nylon, polyester and the self sample fabric. (C) Applied fabrics for the investigations were carried out by using abrasion partner with Korea standard (KS K 0905) cotton, nylon, polyester and the self sample fabric. (D) Electrostatic propensity investigations were carried out by use of sample as silk, nylon, polyester and acrylic fabrics, seperating before finish or after finish. (E) Washing after the finish or the original fabric was carried out by Korea standard method, KS K 0465. Through the investigations, he happened to find many interesting matters and the obtained results are as followings. 1. Electrostatic voltage for the finished fabrics increased more than their original silk, nylon, acrylic fabrics except polyester fabric. (See Table 5) 2. Electrostatic voltage for the finished polyester against K.S. polyester decreased remarkably than the original fabric test. 3. In spite of no problem on electrostatic propensity of silk, it showed high electrostatic voltage between the same nature fabric abrasion, because silk is very weak against abrasion and because the test method had been developed to be useful for only synthetic fabrics. 4. Electrostatic voltage increased more in case of abrasion between different nature of fabrics than the same nature of fabrics. 5. Electrostatic voltage of each fabric increased by repeat of wash. 6. Many investigation data were followed with Contact Electrification Series Principle, another word, the farther each other located fabric on the series abrasion was, the higher electrostatic voltage. (See Fig. 6) 7. Such investigation gives warning of use on the mix fiber spinning service as far as concern with electrification. 8. It may also call attention for such increase of electrification in case any finishing of silk textile.

• Journal of Korean Society of Steel Construction
• /
• v.24 no.1
• /
• pp.129-136
• /
• 2012

This study seeks to evaluate the welding characteristics of SHN400 steel, which is suitable for the steel material used in building structures in KS. For this purpose, the Y-groove weld crack test and hardness, tensile, bending, cross tensile, and charpy V notch tests at the welding point were conducted with specimens taken from the highest, the thickest and the commonly used H-beams for girder or beam members. Each test was conducted under the KS test conditions. All tests results satisfied the requirements of KS and the welding requirements for the proper inelastic behavior of structure, indicating that SHN400 can be used for the building structure as a structural material.

• Journal of the Korean Solar Energy Society
• /
• v.40 no.1
• /
• pp.49-60
• /
• 2020

This study reviewed selected specific windows and reviewed the window performance certification criteria including KS F 2278 and KS L 9107 and analyzed the change in performance based on the change of area. This study also compared the heating and cooling loads of an apartment house applied with window performance reviewed in consideration of insulation and SHGC performance and actual size based on KS F 2278. The analyzed window was a double window composed of aluminum and PVC and the building was the apartment house model of 141 ㎡. The analysis results were as follows. First, as the window glass's thermal performance is superior to frame, the performance degraded in reduced area. In case of selected window, the 1 m × 1m window's thermal performance and SHGC decreased by 35% and 37% respectively compared to 2 m × 2 m window. Secondly, in the comparison of performance for increasing area with 2 m × 2 m and 3 m × 3 m windows, the 3 m × 3 m window's thermal performance and SHCG increased about 14%. Third, in the comparison of heating and cooling loads of the analyzed model considering the apartment house model applied with window performance derived from KS F 2278 and actual figures, the model's total heating and cooling loads increased by 33% with cooling decreasing by 36% and heating increasing by 77%. Above analysis results show that evaluation of window performance based on criteria such as KS F 2278 and KS L 9107 may lead to distortion of performances different from actual products. Thus, it is necessary to suggest new evaluation criteria.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.2
• /
• pp.19-27
• /
• 2007

Dry and wet test methods established by Korean industrial standards to estimate opening size of 3 types of geotextile which are widely used for filter of plastic drain board in Korea are performed to evaluate characteristics of the test methods and to compare the test results. Judging from test results, dry method is a relatively poor test, having lots of problems causing many errors but a simple-quick test. Wet method is a very specific test avoiding many of the problems of dry method such as electrostatic charges, trapping in the geotextiles and so on. However, one of wet test methods, KS K ISO 12956, takes long time to complete a test and is too strict to handle loss of granular material. Generally, opening size of a geotextile by wet test method is smaller than that of dry test method. Especially, opening size by KS F 2126 which is called hydrodynamic method but at present is not used anymore is similar to or smaller than that by KS K ISO 12956 method.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.5
• /
• pp.71-84
• /
• 2009

The communication between the center system and the local controller in the Traffic Signal Controller Specification has been specified by a communication line for the exclusive use and the analog modem serial protocol. Therefore, it can't be adapted in the ITS communication network of the TCP/IP protocol being constructed in the local city. The international and domestic ITS device's communication specification has adapted the DATEX-ASN data exchange technique based on the ethernet communication network. So, this study was performed by the purpose of developing the application communication protocol's standard draft based on the TCP/IP communication protocol for the traffic signal controller, to be able to constitute the traffic signal control system in the ITS communication network. The communication format for 23 items of control, status, and database request etc. which are specified in the standard traffic signal controller was developed by appling the DATEX-ASN data interface procedure and structure which are KS ISO X 14827 Part1, 2, ISO/ DIS 15784 Part-3. To test the developed protocol, the application program for the communication items was developed and according to the test result, the encoding and the decoding transection for all communication items was possible.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.4
• /
• pp.457-465
• /
• 2021

This study analyzed the reality and problems of the defense standard classification system. This paper proposes a plan to perform standard management tasks efficiently through case analysis of domestic and foreign standard classification systems. To continuously solve the problem of military product quality in defense technical data, it is necessary to promptly reflect the civilian's excellent technology and benchmark the civilian standard system to manage high-quality defense standards. First, to analyze the reality, the NATO classification system was analyzed through the private KS of domestic and ICS codes, the US defense standard system of overseas. In the case of the Korean military, the reality of the defense standard classification system was grasped through the National Defense Standards Comprehensive System operated by the Defense Acquisition Program Administration. The classification of the ministry of defense's weapon system and force support system is the most suitable classification system for the Korean military, which is classified into eight weapon systems and six force support standard systems for all steps. Specifically, it was classified into 12 major categories, 66 categories, and 352 sub-categories. In this study, the establishment of the defense standard management system can improve the classification system of new defense standards by reflecting the superior technology of the private sector.

• Journal of radiological science and technology
• /
• v.36 no.1
• /
• pp.1-10
• /
• 2013

IEC publications have applied in many countries all over the world such as Europe or Japan and these also have been published as in dustrial standards (KS) and notifications of Korea Food and Drug Administration (KFDA) in Korea. As the general standard of IEC 60601 series for medical electric (ME) equipment was revised as $3^{rd}$ edition in 2005, additional and particular standards have been revised or established newly. Under these circumstances, it is importance for manufacturing and assembling companies or authorized testing companies to understand the trend for revisions of IEC publications. Therefore in this study, the latest version of 3 IEC standards related to medical X-ray equipment : IEC 60601-2-44 for X-ray equipment for computed tomography (CT), IEC 60601-2-45 for mammographic X-ray equipment and IEC 60601-2-54 for X-ray equipment for radiography or radioscopy were covered and analyzed for trends and features accompanied by revision based on IEC 60601-1 $3^{rd}$ Ed. As KFDA notifications in force have referred to the particular standards based on 2nd edition of IEC 60601-1, those revised version of 3 particular standards were compared to KFDA notifications in force. The features of the latest standards applying IEC 60601-1 $3^{rd}$ Ed were shown as following: 1) Requirements for mechanical hazards, especially (motorized) moving parts were emphasized. 2) Indication and recording of patient dose were required. 3) Risk management process was introduced and enabled to monitor potential risks systematically. 4) DR system (digital radiography system) as well as analogue system (film-screen system) was included in the scope. Presently, KFDA will revise the notifications applying the particular standards based on IEC 60601-1 $3^{rd}$ Ed in a few years. Therefore the features of particular standards applying IEC 60601-1 $3^{rd}$ Ed was expected to help manufacturers, assemblers or testing companies of medical electric equipment understand IEC publications or KFDA notifications slated to be published.